www.fellowes.com

DS-3

© 2010 Fellowes, Inc. Part No. 404124

ENGLISH

OPERATION

Model DS-3

See safety instructions below

SafeSense ® Technology (yellow)

PAPER

Safe Sense ® override switch

Auto-On ( ) Off Reverse (R)

Continuous operation: 4-5-minute maximum

Press Auto-On ( )

NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 4-5-minutes will trigger 20-minute cool down period.

Feed into paper entry and release

CARD

Press Auto-On ( )

Feed into paper entry and release

TROUBLESHOOTING

Shredder doesn’t start:

Paper jam: Set to Off (O), remove shredder head and empty bin. Replace shredder head, and follow any or all of the below procedures.

Yellow - SafeSense ® active

Yellow flashing - SafeSense ® not active

Make sure head is on basket correctly

Breakthrough Safety Technology! SafeSense ® stops shredding when hands are too close to the opening.

Wait 20 minutes for motor to cool down

— To Test SafeSense ® Technology

SET-UP

Place head on basket as shown: Disconnect power switch must be in ON ( I ) position to operate shredder.

Press Auto-On ( )

CAPABILITIES

Will shred: Paper, small paper clips, credit cards and staples

Will not shred: Continuous forms, adhesive labels, transparencies, newspaper, cardboard, large paper clips, laminates or plastic other than noted above

Paper shred size: Cross-Cut.......................................................................... 5/32” x 2” (3.9 x 50mm)

Maximum: Sheets per pass (Cross-Cut)..................................................................................10* Cards per pass........................................................................................................ 1 Passes per day................................................................................................ 10-20 Paper width.............................................................................................9”/229mm Continuous operation.............................................................................. 4-5 minutes

• 20 lb., 8.5”x11” paper at 120v, 60 Hz, 3.8Amps; heavier paper, humidity or other than rated voltage may reduce capacity.

Fellowes SafeSense ® shredders are designed to be operated in home and office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40

• 80% relative humidity.

IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!

• Keep away from children and pets. Keep hands away from paper entry. Always unplug when not in use.
• Never use aerosol, petroleum-based or other flammable products on or near shredder. Do not use canned air on shredder.
• Keep foreign objects – gloves, jewelry, clothing, hair, etc.– away from shredder openings. If object enters top opening, 15 press and hold Reverse (R) to back out object.
• Do not use if damaged or defective. Do not open shredder head. Do not place near or over heat or water source.
• 10 sheets per pass to avoid jams.
• Avoid touching exposed blades under Cross-Cut shredder head.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.

Press and hold Reverse (R) 2-3 seconds

Alternate slowly back and forth

Gently pull uncut paper from paper entry. Plug in.

Set to Off (O) and unplug

ATTENTION: If the SafeSense ® light remains on, you must engage the SafeSense ® feature. (See SafeSense ® instructions below.)

Remove and empty basket

Press and hold Reverse (R)

Override Switch in order to perform steps above. Once the jam is cleared, reset the

Sensor light illuminated–paper jammed

SafeSense ® paper jam: If the SafeSense ® feature activates (SafeSense ® light remains on) to cause the user to think the shredder has jammed when it has not, use the Override Switch to deactivate the SafeSense ® feature and clear the paper. Warning – when switch is in override position, the SafeSense ® light will flash and the SafeSense ® feature will NOT function. Once the paper is cleared, reset the SafeSense ® feature.

SafeSense ® override switch

MAINTENANCE

Run regularly in reverse for one minute

Oil when bin is full, or immediately, if:

• Capacity decreases
• Motor sounds different, or Shredder stops running

Follow oiling procedure below and repeat twice.

• Apply oil Press Auto-On ( ) Shred one sheet across entry
• Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250

Press and hold Reverse (R) 2-3 seconds

WARRANTY

LIMITED WARRANTY Fellowes, Inc. (“Fellowes”) warrants the cutting blades of the machine to be free from defects in material and workmanship for 3 years from the date of purchase by the original consumer. Fellowes warrants all other parts of the machine to be free of defects in material and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, or unauthorized repair. ANY IMPLIED

WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer.