Page 1 of 3
Text on page 2
POWERSHRED 465Ms
POWERSHRED 465Ms
LIMITED PRODUCT WARRANTY / GARANTÍA LIMITADA DEL PRODUCTO/ GARANTIE LIMITÉE DU PRODUIT
Limited Warranty: Fellowes, Inc. (“Fellowes”) warrants the parts of the machine to be free of defects in material and workmanship and provides service and support for 1 year from the date of purchase by the original consumer. Fellowes warrants the cutting blades of the machine to be free from defects in material and workmanship for 1 year from the date of purchase by the original consumer. If any part is found to be defective during the warranty period, your sole and exclusive remedy will be repair or replacement, at Fellowes’ option and expense, of the defective part. This warranty does not apply in cases of abuse, mishandling, failure to comply with product usage standards, shredder operation using an improper power supply (other than listed on the label), or unauthorized repair. Fellowes reserves the right to charge the consumers for any additional costs incurred by Fellowes to provide parts or services outside of the country
where the shredder is initially sold by an authorized reseller. ANY IMPLIED WARRANTY, INCLUDING THAT OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED IN DURATION TO THE APPROPRIATE WARRANTY PERIOD SET FORTH ABOVE. In no event shall Fellowes be liable for any consequential or incidental damages attributable to this product. This warranty gives you specific legal rights. The duration, terms, and conditions of this warranty are valid worldwide, except where different limitations, restrictions, or conditions may be required by local law. For more details or to obtain service under this warranty, please contact us or your dealer.
Factory Service
Questions or Concerns?
www.fellowes.com
Troubleshooting Registration Manuals
Customer Service & Support
Replacement parts General questions
Please read these instructions before use. Do not discard: keep for future reference.
©2015 Fellowes, Inc. Part No. 409344
Quality Office Products Since 1917
Page 2 of 3
Text on page 3
PAPER OR CD/CARD
Model 465Ms
BASIC SHREDDING OPERATION
ENGLISH
A. SafeSense ® Technology
B. CD entry
C. See safety instructions
D. Paper/card entry
E. Pull-out bin
F. Window
G. Casters
H. ON/OFF switch
1. OFF
2. ON
Continuous operation: Up to 12-minutes maximum NOTE: Shredder runs briefly after each pass to clear entry. Continuous operation beyond 12-minutes will trigger 25-minute cool down period.
KEY
I. Control Panel and LEDs
- Overheat (red)
- SafeSense ® indicator (yellow)
- ON/OFF (blue)
- Reverse
- Forward
Plug in and turn ON (I)
Feed paper/card straight into paper entry and release
When finished shredding set to OFF (O)
Hold CD at edge, feed into center of entry and release
ADVANCED PRODUCT FEATURES
SafeSense ® Technology Stops shredding immediately when hands touch the paper opening.
SilentShred™ Technology SilentShred™ noise quality shreds without noisy disruptions.
SAFESENSE ® TECHNOLOGY
Stops shredding immediately when hands touch the paper opening.
SET-UP AND TESTING
CAPABILITIES
Will shred: Paper, credit cards, CD/DVDs and staples
Will not shred: Adhesive labels, continous form paper, transparencies, newspaper, cardboard, laminates, paper clips, file folders, X-rays or plastic other than noted above
Paper shred size: Micro-Cut................................................................... 1/8 in. x 13/32 in. (3mm x 10mm)
Card/CD shred size: Strip-Cut.................................................................................................19/32 in. (15mm)
Turn the shredder ON (I) to activate SafeSense ®
Maximum: Sheets per pass............................................................................................................ 12* Cards/CDs per pass........................................................................................................ 1* Paper entry width............................................................................. 8-15/16 in. (227mm) CD entry width..................................................................................... 4-7/8 in. (124mm)
Touch test area and look for the SafeSense ® indicator to illuminate
SafeSense ® is active and working properly
For more information about all of Fellowes Advanced Product Features go to www.fellowes.com
PRODUCT MAINTENANCE
- 8.5 in. x11 in., 20lb., (75g) paper at 120V, 60 Hz, 5.8Amps; heavier paper, humidity or other than rated voltage may reduce capacity. Maximum recommended daily usage rates: 12 sheets per pass to avoid jams.
500 sheets per day; 25 credit cards; 10 CDs.
Fellowes SafeSense shredders are designed to be operated in home and office environments ranging between 50 – 80 degrees Fahrenheit (10 – 26 degrees Celsius) and 40 – 80% relative humidity.
OILING SHREDDER
CLEANING AUTO-START INFRARED SENSORS
All micro-cut shredders require oil for peak performance. If not oiled, a machine may experience diminished sheet capacity, intrusive noise when shredding, and could ultimately stop running. To avoid these problems, we recommend you oil your shredder each time you empty your waste bin.
Paper detection sensors are designed for maintenance free operation. However, on rare occasions the sensors may become blocked by paper dust causing the motor to run even if there is no paper present. (Note: two paper detection sensors are located in the center of the paper entry) .
FOLLOW OILING PROCEDURE BELOW AND REPEAT TWICE
TO CLEAN THE SENSORS
IMPORTANT SAFETY INSTRUCTIONS — Read Before Using!
- Operation, maintenance, and service requirements are covered in the instruction manual. Read the entire instruction manual before operating shredders.
- Keep away from children and pets. Keep hands away from paper entry. Always set to off or unplug when not in use.
- Keep foreign objects – gloves, jewelry, clothing, hair, etc. – away from shredder openings. If object enters top opening, switch to Reverse ( ) to back out object.
- Never use aerosol products, petroleum based lubricants or other flammable products on or near shredder. Do not use canned air on shredder.
- Do not use if damaged or defective. Do not disassemble shredder.
Do not place near or over heat source or water.
- Apply oil across entry Press and hold forward ( ) 2-3 seconds
- This shredder has an ON/OFF Switch (H) that must be in the ON ( ) position to operate shredder. In case of emergency, move switch to OFF (O) position. This action will stop shredder immediately.
Turn OFF (O) and unplug shredder
Locate Auto-start infared sensor
Dip cotton swab in rubbing alcohol
Using cotton swab, wipe away any contamination from the paper sensors
- Only use a non-aerosol vegetable oil in long nozzle container such as Fellowes 35250
- Avoid touching exposed cutting blades under shredder head.
- Shredder must be plugged into a properly grounded wall outlet or socket of the voltage and amperage designated on the label. The grounded outlet or socket must be installed near the equipment and easily accessible. Energy converters, transformers, or extension cords should not be used with this product.
Go to Support Section at www.fellowes.com or see back page of manual for useful telephone numbers.
TROUBLESHOOTING
- FIRE HAZARD – Do NOT shred greeting cards with sound chips or batteries.
Overheat Indicator: When the Overheat Indicator is illuminated, the shredder has exceeded its maximum operating temperature and needs to cool down. This indicator will remain illuminated and the shredder will .not operate for the duration of the recovery time. See Basic Shredding Operation for more information about the continuous operation and recovery time for this shredder.
- For indoor use only.
- Unplug shredder before cleaning or servicing.
SafeSense ® Indicator: If hands are too close to the paper entry, the SafeSense ® indicator will illuminate and the shredder will stop shredding.
Page 3 of 3 · End of manual
Quick start
- Plug in and turn the ON/OFF switch to ON (I).
- Feed paper or a card straight into the paper/card entry and release (up to 12 sheets).
- Hold a CD at the edge and feed it into the center of the CD entry.
- Keep continuous runs to 12 minutes or less.
- Set to OFF (O) when finished.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Overheat light on and shredder won't run | Maximum operating temperature exceeded | Wait for the 25-minute recovery time. Page 3 |
| Shredder stops and SafeSense light is on | Hands too close to the paper entry | Move hands away from the entry. Page 3 |
| Motor runs with no paper in the entry | Auto-start sensors blocked by paper dust | Turn off and unplug, then wipe the two sensors in the center of the paper entry with a cotton swab dipped in rubbing alcohol. Page 3 |
| Reduced sheet capacity, extra noise, or shredder stops running | Cutters need oil | Set to Off, apply non-aerosol vegetable oil across the entry, run in Reverse for 2-3 seconds, and repeat twice. Page 3 |
Frequently asked questions
How many sheets can the Powershred 465Ms shred at once?
Up to 12 sheets of 20 lb, 8.5" x 11" paper per pass and 1 CD or card. Recommended daily use is 500 sheets, 25 credit cards and 10 CDs. See page 3.
What can it shred, and what should I keep out?
It shreds paper, credit cards, CDs/DVDs and staples. Do not shred adhesive labels, continuous form paper, transparencies, newspaper, cardboard, laminates, paper clips, file folders or X-rays.
How long can it run continuously?
Up to 12 minutes. Running longer triggers a 25-minute cool-down period. See page 3.
How often should I oil it?
Fellowes recommends oiling each time you empty the bin. Apply a non-aerosol vegetable oil (such as Fellowes 35250) across the entry, press and hold Forward for 2-3 seconds, and repeat twice.
How do I test SafeSense?
Turn the shredder ON, touch the test area and check that the yellow SafeSense indicator lights. See page 3.
