Page 1 of 4
Text on page 2
WOW
Floor Swing Panels (694/695)
Hardware List
Top Cross Bar w/ deep holes
Middle Cross Bar w/ angle support
Bottom Cross Bar w/ shallow holes
Should you require assistance during assembly, please call our Customer Service Department Monday - Friday 8 a.m. - 5 p.m. Central Standard Time
Toll-Free Customer Service
Page 2 of 4
Text on page 3
Floor Swing Panels
Assembly Diagram
R EAD T HROUGH I NSTRUCTIONS FROM BEGINNING
TO END BEFORE STARTING TO ASSEMBLE UNIT .
- To Assemble:
Identify and Separate all the Parts and Hardware.
- Assemble Top Cross Bar with deep holes (P-2) with holes facing down on top of the Legs (P-1), and Middle Cross Bar with angle support (P-3) with holes facing up. Also assemble Bottom Cross bar with holes facing to the floor (P-4) between the 2- Legs (P-1) by using Socket Screws (A), and Interior Threaded Post (B) and tighten with Allen Wrench (D). See illustration # 1. If you have 20 panel unit, see additional instruction sheet with Cross Bars before you do any other step.
- Install Glides (C) one at the time, as shown in illustration # 2 and # 2a.
Missing Parts or UPS Damaged Parts For your convenience you can EMAIL us at
24 HOURS 7 DAYS A WEEK
Page 3 of 4
Text on page 4
- Remove the poly cover from both sides of the Acrylic Panels (P-7). Slide the White Poster Panel (P-6) or Hook & Loop boards (optional) in between the Acrylic Panels (P-7) and insert into the Panel Frame (P-5) as shown in illustration # 3. If you have 694U or 695U models you would not have Acrylic Panels (P-5).
- Insert one tab of Panel Spacer (E) in punched slot and, using your thumb, compress the Spacer (E) until the second tab inserts into the second slot. See illustration # 4 and # 4a. There are 2- Spacers (E) per each Panel Frame (P-5).
- Place the long stub coming out of the Panel Frame (P-5) into first hole underneath the Top Cross bar (P-2), push up as far as it goes into the hole and set the smaller stub on the bottom of the Panel frame (P-5). Line up with the first hole on the Bottom Cross bar (P-3) as shown in illustration # 5. Repeat the same step to place all your Panel Frames (P-5).
- Slide the U-Channel (P-8) on top of each Panel Frame (P-5). This step will secure all panels from falling off. See illustration # 6 and # 6a. To access the panels you must remove the U-Channel (P-8) to bring the Panel Frame (P-5) down.
Do not use unless all screws are tight. At least every six months, check all screws to be sure they are tight. If parts are missing, broken, damaged, or worn, stop use of the product until repairs are made by your dealer using factory authorized parts.
Page 4 of 4 · End of manual
Quick start
- Identify and separate all parts and hardware.
- Attach the Top Cross Bar (P-2, deep holes facing down), Middle Cross Bar with angle support (P-3, holes up) and Bottom Cross Bar (P-4, holes facing the floor) between the two legs (P-1) using socket screws (A) and interior threaded posts (B); tighten with the Allen wrench (D).
- Install the glides (C) one at a time.
- Remove the poly cover from the acrylic panels (P-7), slide the white poster panel (P-6) or optional hook-and-loop board between them and insert into the panel frame (P-5).
- Fit two panel spacers (E) per frame by inserting one tab and compressing the spacer until the second tab snaps into its slot.
- Push each frame's long top stub into the holes under the top cross bar and set the short bottom stub into the matching lower hole.
- Slide a U-channel (P-8) over the top of each panel frame to keep the panels from falling off.
Frequently asked questions
How do I get a panel out of the floor swing panel display?
Remove the U-Channel (P-8) from the top of the panel frame, then bring the frame down. See page 4.
Do the 694U and 695U models have acrylic panels?
No. The instructions note that the 694U and 695U models do not include acrylic panels. See page 4.
How often should I check the screws?
At least every six months. Do not use the unit unless all screws are tight. See page 4.
