Page 1 of 5
Text on page 2
FD 215S Semi-Automatic Paper Creaser
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
OPERATOR MANUAL
FIRST EDITION
Page 2 of 5
Text on page 3
SPECIFICATIONS
Operation Panel
Guide Rail
FUNCTION:
The Formax FD 215S Semi-Automatic Paper Creaser is designed to prevent cracking in toner-based digital printouts. Creasing sheets prior to folding ensures a clean, professional finish and makes it easier for folding devices to fold with accuracy.
Maximum paper width:
Up to 18” (460mm)
Maximum paper thickness:
Width of crease:
Depth of crease:
Dimensions:
27.95” W x 21.25” D x 9” H (710 x 540 x 245mm)
Weight:
Power:
110V AC, 60Hz, 120 watt
UNPACKING
Check package for shipping damage. If there is shipping damage, do not discard the box.
When choosing a location for the creaser, avoid the following: direct sunlight, areas of high temperature or humidity, areas without proper ventilation, or surfaces that are unstable.
Open the box, and pull the bands to remove the machine. Remove all protective packaging.
SAFETY NOTES
To avoid personal injury and/or damage to the machine, DO NOT place hands, fingers or any objects other than the paper to be creased inside the creasing channel
Keep any loose items including ties, jewelry or long hair away from the creasing channel, to avoid injury.
Children should not be allowed to operate the machine.
In the event the creaser needs to repaired, turn off and unplug the machine. Contact your Formax Dealer for repair.
Page 3 of 5
Text on page 4
SETUP
Foot Pedal Switch Jack
Operation Mode Changeover Switch
Power Switch with Light
Power Inlet with Fuse
Remove the foot-control pedal from the box and attach it to the foot pedal switch on the Operation Panel. Be sure to align the pins correctly to avoid damage. Place the foot pedal on the floor.
Remove the power cord from the box and plug into the Power Inlet on the Operation Panel. Be sure the voltage from the wall outlet matches the voltage of the creaser.
OPERATION
Plug in and turn on the creaser. Be sure the red power indicator light is on.
Using the Changeover Switch (Fig. 1), choose the operating mode:
With switch in upper position (-), the creaser is in Manual Mode. The creaser will crease one time, with a single touch of the switch, and will automatically return to the center position (0).
With the switch in the center position (0), the machine is in standby but not operating.
With the switch in the lower position (=), the creaser is in Semi-Automatic Mode. After inserting the paper, the machine will crease one time after the foot pedal is pressed, then will return to standby mode.
It is suggested to leave the switch at (=) for Semi-Automatic Mode.
Loosen thumbscrews on each side guide (Fig. 2).
Slide side guides to correct location based on desired placement of crease. When moving the side guides, lift gently while sliding to avoid damage to the guide rail.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 4 of 5
Text on page 5
Load paper by sliding through creasing channel under mechanism cover (Fig. 3).
Once the paper is aligned between the side guides, crease by using manual switch (Fig. 4) or foot pedal (Fig. 5). See Step 2 for explanation of modes.
Once the paper is creased, remove it from the creaser (Fig. 6).
TWO-PART CREASING (BOOK SPINE CREASING)
Measure sheet to be creased.
Move right side guide to correct location and tighten thumbscrew.
Load sheet and align with right side guide. Engage creaser with foot pedal or manual control button. Remove sheet.
For second crease, move left side guide to correct location and tighten thumbscrew.
Load sheet and align with left side guide. Engage creaser with foot pedal or manual control button. Remove sheet.
MAINTENANCE
- If the creaser will not be used for an extended period of time, turn off the power and unplug for safety.
- After each use, turn off the creaser and clean the surface with a dry cloth.
- To provide smooth operation, periodically apply a couple of drops of lubricating oil to the two mandrils and axletree connecting position.
Page 5 of 5 · End of manual
Quick start
- Unpack: Open the box and pull the bands to remove the machine. Remove all protective packaging. Avoid sunlight, heat, humidity and unstable surfaces when choosing a spot.
- Attach the foot pedal: Attach the pedal to the foot pedal switch on the operation panel. Align the pins correctly. Place the pedal on the floor.
- Connect power: Plug the power cord into the power inlet. Make sure the wall outlet voltage matches the creaser.
- Turn on and pick a mode: Turn on the creaser and check that the red power light is on. Use the changeover switch for Manual Mode, standby or Semi-Automatic Mode.
- Set the side guides: Loosen the thumbscrews on each side guide. Slide the guides to the crease position. Lift gently while sliding.
- Crease: Slide paper through the creasing channel under the mechanism cover. Align it between the side guides. Crease with the manual switch or the foot pedal.
- Remove and clean up: Remove the creased paper. After each use, turn off the creaser and clean the surface with a dry cloth.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not crease after paper is loaded | The changeover switch may be in the center (0) standby position. | Move the switch to the upper position (-) for Manual Mode or the lower position (=) for Semi-Automatic Mode with the foot pedal. Page 4 |
| Guide rail damage while moving side guides | The guides were slid without lifting. | Loosen the thumbscrews and lift gently while sliding the side guides. Page 4 |
| Hands or loose items near the creasing channel | Fingers or loose items can cause injury. | Do not place hands, fingers or objects other than paper in the creasing channel. Keep ties, jewelry and long hair away. Page 3 |
| Creaser needs repair | The machine has a fault. | Turn off and unplug the machine. Contact your Formax Dealer for repair. Page 3 |
| Operation is not smooth | The moving parts may need lubricating. | Periodically apply a couple of drops of lubricating oil to the two mandrils and axletree connecting position. Page 5 |
| Foot pedal does not connect | The pins may not be aligned. | Align the pins correctly when attaching the pedal to the foot pedal switch jack to avoid damage. Page 4 |
Frequently asked questions
What does the FD 215S do?
It creases sheets to prevent cracking in toner-based digital printouts. Creasing before folding gives a clean finish. See page 3.
What is the maximum paper width?
Up to 18 inches (460mm). See page 3.
What is the difference between Manual and Semi-Automatic Mode?
In Manual Mode one touch of the switch creases once. In Semi-Automatic Mode the machine creases once each time you press the foot pedal. See page 4.
How do I do a book spine crease?
Use two-part creasing. Set the right guide and crease, then set the left guide and crease the sheet a second time. See page 5.
What power does the FD 215S use?
110V AC, 60Hz, 120 watt. See page 3.
