FD 346 / FE 346

Document Folder

FI / FJ Series

OPERATOR MANUAL FIRST EDITION

TABLE OF CONTENTS

SUBJECT

PAGE

DESCRIPTION

SPECIFICATIONS

UNPACKING

SETUP

CONTROL PANEL

OPERATION

SETTING CUSTOM FOLDS

AUTOBATCH MODE

MULTI-SHEET FEEDING (OPTIONAL)

CROSS FOLDING

STACKER WHEEL POSITIONING CHART

STACKER WHEEL SETUP FOR THICK PAPER

REMOVING OUTFEED COVER

REMOVING INFEED TIRES

OPERATOR MAINTENANCE

ERROR SCREENS

TROUBLE-SHOOTING

DESCRIPTION

Self Centering Paper Side Guides

Infeed Tray Extension

Telescoping Outfeed Stacker

Infeed Tray Lever

Lower Fold Table

Power Inlet & Circuit breaker

FUNCTION

This document folder is designed to perform a wide variety of folds using a variety of paper weights. The fold plates are manually adjusted for standard folds and custom folds. Batch counting, self-centering side guides, and the capability to cross-fold are added features. The folder will automatically stop after the last document has been folded.

SPECIFICATIONS

Speed:

Standard Mode: Up to 15,500/hour, depending on fold type

Hopper Capacity:

Up to 500 sheets of 20# paper (75gsm)

Paper size:

Min: 3.5” X 5” (88.9 W x 127 L mm)

Max: 12.25” X 18” (311 W x 457 L mm)

Pre-Marked fold types:

Pre-Marked Paper Sizes:

FD Model: 11”, 14”, 17”

FE Model: A5, A4, A3, B6, B5, B4

Weight:

67 lbs (30 kg)

Power:

FD Model: 120 volts A.C., 50/60 Hz, 2 amps.

FE Model: 220 volts A.C., 50/60 Hz, 2 amps

Safety Certifications:

UL, CUL, & CE Approved

UNPACKING & SETUP

Check package for shipping damage. If there is shipping damage, do not discard the box.

Remove the machine and packed components from the box. The fold plates, telescoping stacker, Optional Multi Sheet Feeder if ordered, power cord and cross-fold guide are wrapped separately in the box.

NOTE: Two people must lift the machine from the box.

Place the folder on a solid wooden or metal stand.

Install upper and lower fold plates, telescoping conveyor multi-sheet feeder and power cord

Upper Fold Table Pins

Be sure the plates are set firmly on the locating pins (Fig 1a & 1b). Slide each fold plate in until it meets the first locating pin then push down to set in place.

Repeat the same steps for the lower fold plate.

Lower Fold Table Pins

Insert the telescoping extension tray into the end of the outfeed conveyor (Fig. 2).

4. If equipped, insert the optional Multi-Sheet Feeder into the four slots located on the top cover (Fig 3). Note: Technical assistance is required to install the multisheet feeder components if it is purchased separetly from the folder.
5. Make sure the power switch is in the “OFF” position. Plug the power cord into the power inlet and the wall outlet.

CONTROL PANEL

Main Screen:

AutoBatch Mode Screen:

NAME

FUNCTION

Resets the counter to “000000”

Press to start the Folder

Test folds one document

Press to enter the Batch mode

Press to stop the folder

AutoBatch Mode: Number Folded Sets

Press to enter the number of batched sets (up to 999 sets)

AutoBatch Mode: Number of documents

Press to enter the number of documents in a batched set (up to 999 documents)

AutoBatch Mode: Delay between sets

Press to enter the time delay between each set (up to 99 seconds)

Press to return to the main screen

OPERATION

Place power switch in the “ON” position.

To set the fold plate stop position, squeeze the stop plate lever and move the stop plate to the desired location on the upper and lower fold plates (Fig 4). Align the pointed part of the stop plate with the desired marks on the decal and release the lever. Fine adjustments can be made with the adjustment knob at the end of the plate (Fig 5).

NOTE: When doing a “Single” fold, be sure to move the lower fold plate stop all the way to the front of the plate. The plate must be firmly reinstalled on the locating pins.

Stacker Wheel Positions A, B & C

Move the stacker wheels to the proper position for the paper size (Fig 6) ( Refer to chart on page 7).

Extend the telescoping conveyor stacker as required.

Lift the in-feed tray extension into position.

Raise the in-feed tray lever.

Set the paper side guides for the paper you’re using and lock in position.

Neatly stack paper on the in-feed tray.

Lower the in-feed tray lever.

Press the “ ” icon on the control panel to check the folds. Adjust as needed.

If the fold is skewed use the skew adjustment knob to make corrections (Fig.7).

When you’re satisfied with the test folds, press the “ ” icon to operate the machine.

SETTING CUSTOM FOLDS

Example 1: Uneven “Z”

Measure the length of panel “A”

Panel A

Adjust the upper fold plate so that the stop plate lines up with the measurements of the panel “A” i.e. if panel “A” is 5 1/4” long slide the stop plate up or down so that it lines up with the 5 1/4” mark on the fold plate.

Panel B

Measure the length of panel “B”

Adjust the lower fold plate so that the stop plate lines up with the measurement of panel “B”

Load forms and press test. If folds are too long or too short adjust accordingly.

Example 2: Uneven “C”

Measure the length of panel “A” & “B”

Adjust the upper fold plate so that the stop plate lines up with the measurements of panel “A” & “B”. i.e. if panel “A” & “B” are 10 1/2” long slide the stop plate up or down so that it lines up with the 10 1/2” mark on the fold plate.

Measure the length of panel “B”

Adjust the lower fold plate so that the stop plate lines up with the measurement of panel “B

Load forms and press test. If folds are too long or too short adjust accordingly.

Panel A

Panel B

AUTOBATCH COUNTING MODE

The AutoBatch feature can be set to count down the number of sets in a batch, the number of sheets in each set, and the delay between each set. To enter the AutoBatch Mode press the “ “ icon on the main screen.

To enter the number of sets press the “

“ (fig. 8a). Enter

the number of sets on the keypad that appears. Next press the

“ icon to select the number of sheets, and then press the

“ icon to enter the delay between sets. Press the “

Press the “ “ icon to begin folding. The folder will stop when the number of sets counts down to zero (0).

To exit the AutoBatch Mode press the “

Note: Press the “ “ icon on the keypad to exit back to the Auto Batch screen. Press the “ “ icon to edit the number entered. Press the “ “ icon on the keypad to reset the entered number to zero (0).

MULTI-SHEET FEEDING (OPTIONAL)

The multi-sheet feeder is designed to fold pre-collated stapled or unstapled sets of up to four 20 # (75gsm)sheets of paper. NOTE: This feature will not work in AutoBatch mode. The home screen must be displayed in order for the multisheet feeder to work properly.

Adjust the side guides on the multi-sheet feeder for the proper paper size. Loosen the thumb screw, adjust the guides to fit the paper width and re-tighten the thumbscrew (Fig 9a).

Slide the pre-collated paper set into the multi-sheet feeder. When feeding stapled sets the documents should be placed with the staple on the operator’s side and leading (Fig 9b).

The sheets of paper will be automatically pulled into the folder.

If the fold is skewed, turn the skew adjustment knob located on the back of the feeder left or right to make corrections (Fig 9c).

To remove the multi-sheet feeder depress the release levers located on either side of the lower back side of the feeder (Fig. 9d), tilt the feeder forward and lift. To reinstall depress the levers and reinsert.

CROSS FOLDING

Cross folding refers to folding a document in one pass and then running it through the folder a second time to be folded again.

Common Application: Folding a 11” x 17” document in half and then letter folding it to fit in a standard #10 envelope.

1. Load folded paper into the feed tray with the fold crease facing the non-operator side of the folder (Fig 10a).

Note: For best results, firmly run your hand over the fold crease to help flatten the paper before loading.

2. Attach the cross fold paper guide onto the feed tray paper guide (Fig. 10b) and lower guide.

Note: Cross folding ability will vary based on the paper weight and type. If the paper is too heavy it may not be able to be cross folded.

To install cross fold guide hook tab “A” into slot “A” and then lower tab “B” into slot “B”

Note: The guide can be conveniently stored under the lower fold table when not in use (Fig 10c).

Cross fold guide storage

STACKER WHEEL POSITIONING GUIDE

Move the stacker wheels to the proper position indicated on the chart based on the fold and paper size (Fig 11a and 11b).

Letter Zig-Zag Single Gate Fold Out Double ll

8.5" x 11" 8.5" x 14" A A or B A A or B B B A B B C A A

11" x 17" B B C C C A or B

STACKER WHEEL SETUP FOR THICK PAPER

Thicker paper from 28 # up to 65 # may require special stacker

wheel setup moving the stacker wheels closer than the position “A” slot.

If stacking is inconsistent move the stacker wheels from the standard position #1 (Fig. 12a) to the thick paper weight position #2 (Fig. 12b) as indicated in the pictures below, position # 2 may also be good for small folded documents.

Fig. 12a - Standard Stacker Wheel Position

Fig. 12b - Thick Paper Weight Position

REMOVING OUTFEED COVER

The outfeed cover can be removed to access the exit roller. To remove, unscrew thumbscrews that hold the cover in place (Fig. 13)

REMOVING INFEED TIRES

The infeed tires can easily be removed for cleaning and replacement. Remove the Allen screw located on the left side of the feed tire shaft (Fig. 14a). Slide the shaft to the right to release from the side frame and remove (Fig. 14b).

OPERATOR MAINTENANCE

1. I t is recommended to let forms cool for one-half hour, from the laser printer, before folding. This allows toner to set

on the forms and static electricity to discharge. The FD 402 Jogger is recommended for best results. The Jogger squares the forms and dissipates heat and static electricity created by laser printers.

2. Clean in-feed tires and fold rollers with Formax recommended roller cleaner & rejuvenator to remove paper dust and toner. A Formax Cleaner Kit is available from your dealer. A damp cloth with water is the best alternative.

CAUTION: Do not use any chemicals other than the roller cleaner & rejuvenator or water.

CLEANING PROCEDURES:

1. Make sure machine is turned off and unplugged. All folders have four (4) rubber rollers (Fig. 15).
2. Remove the upper and lower fold plates.
3. Using Formax roller cleaner, spray a new cotton cloth until the cloth is saturated. Wipe the wet cloth in a back and forth motion making sure to clean the entire surface of the fold rollers. Next use a dry cloth and wipe off excess toner. The cloth should be covered with black toner surplus from cleaning the rollers.
4. Run 10-15 sheets of blank copy paper through the folder to ensure all cleaner has been removed from the fold rollers. Running blank sheets will remove any excess residue of cleaner on the rollers.

ERROR SCREENS

FD 342 Touch Screen -Error Screens

Paper Mis-Feed / Paper Jam Paper

Jam

Paper misfeed

FD 342 Touch Screen -Error Screens

A mis-feed has occurred. Reset the stack of paper in Error screen appears with arrows pointing to possible areas the and the press the arrow “ “ icon resume opto in-feed check. Press return to go back to to home screen eration. A Paper occurred in one the areas at any time. If the jam jam has is not cleared the error of screen will Error screen will appear with arrow pointing to infeed. Error screen appears with arrows pointing to possible areas Press return or arrow to go back to the home and screen. unappear again after start 1x. to check. Press the return arrow to go back to home pressing screen indicated. Turn the folder to the off position at any time. If the jam is not cleared the error screen will appear again after pressing start or 1x. plug. Check the area indicated for paper and remove. Replace the fold plates and plug the folder in and the Cover Open Paper Out power on.

Error screen will appear with arrow pointing to infeed. Press return arrow to go back to the home screen.

Cover Open

Paper Out

Paper Out

Error screen will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

Cover Open

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

• Paper Out screen will come on if start is pressed and the is no paper in the feed tray.

FD 342 Touch Screen -Error Screens

misfeed Error Paper screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

misfeed Error screen Paper will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

The top cover is open. Close the top cover and press the “ “ icon to resume operation.

• Paper is Out come on if start is pressed and and There no screen paper will in the in-feed. Reload paper the is no in the feed tray. press the paper “ “ icon to resume operation.

rs with arrows pointing to possible areas return arrow to go back to home screen am is not cleared the error screen will pressing start or 1x.

pear with arrow pointing to empty eturn arrow to go back to the home

will come on if start is pressed and he feed tray.

Error screen will appear with arrow pointing to infeed. Press return arrow to go back to the home screen.

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

Error screen appears with arrows pointing to possible areas to check. Press the return arrow to go back to home screen at any time. If the jam is not cleared the error screen will appear again after pressing start or 1x.

Error screen will appear with arrow pointing to infeed. Press return arrow to go back to the home screen.

Error screen will appear with arrow pointing to empty infeed tray. Press return arrow to go back to the home screen.

Error screen will apear with arrow pointing to open cover with indicator to close cover. Press return arrow to go back to the main screen.

• Paper Out screen will come on if start is pressed and the is no paper in the feed tray.

TROUBLE-SHOOTING

TROUBLE

POSSIBLE CAUSE

REMEDY

Control panel is not illuminated.

No power at the wall outlet.

No power to the machine inlet.

Check power cord for frayed/broken wires.

No power to the control panel.

Press the button on the circuit breaker.

Magnetic switch is broken.

“Paper out “ screen.

In-feed tray is empty.

Place documents on the in-feed tray.

Paper jammed at exit of folder. Black marks on the folded In-feed tires, separator, and/or paper. fold rollers are dirty.

Remove paper. Clean the parts with approved roller cleaner and rejuvenator.

In-feed tray is out of adjustment.

Turn skew adjuster knob to remove the skew.

Stacker belts do not turn.

Broken drive belt, worn drive gear.

Documents are wrinkled or crunched.

Fold plates are not inserted correctly.

Remove and reinstall fold plates. Be sure they’re properly positioned.

Piece of paper or other material Remove object from the fold plate. is stuck in the fold plate.

In-feed tray lever does not work

Jog forms to remove static electricity.

Feed tire or separator worn

Feed tire or separator worn Fiolder is in AutoBatch Mode

Call for Service Select the “

Multi-Sheet feeder not working

“ icon to return to the

Photo-eye not working properly Call for Service