Page 1 of 10
Text on page 2
FD 402TA1 Tabletop Air Jogger
OPERATOR MANUAL
Page 2 of 10
Text on page 3
Introduction
Thank you for purchasing this product.
Please carefully read this Operator Manual before use.
Be sure to read "Safety instructions" before use.
Keep this Operator Manual in a specific place for handy reference
1. Safety Instructions …………………………….........................................................3
2. Precautions Before Use.........................................................................................5
3. Components and Functions...................................................................................6
6. Other Matters to Note.............................................................................................8
Page 3 of 10
Text on page 4
- Safety Instructions
To prevent bodily injury or damage to property, please follow these safety instructions.
Safety instructions
Definition of Symbols and Notes
In this manual, the following words and symbols denote possible danger.
Danger
This Symbol stands for immediate danger threatening the life and health of
persons. Disregarding these instructions may cause severe damage to health and
Caution
This symbol stands for an endangering situation that may occur. Disregarding
these instructions may lead to minor injury or damage to property.
Note
This symbol stands for notes, operational hints, and other useful information.
Danger
Do not place receptacles containing water on
Do not put any foreign object, such as metal or
the machine. If water is spilled, it may cause fire
flammable object inside the machine. It may cause
or an electrical shock.
fire or an electrical shock.
Do not touch any revolving and/or moving part
Do not remove the machine cover, back cover, etc.
of the machine with a hand, or reach a hand
This will expose parts with very high voltage that
into the machine. It may cause a bodily injury.
may cause an electrical shock.
Do not dismantle, remodel, or repair the
Do not use any other voltage than the voltage
machine. It may cause fire, electrical shock, or
specified on the serial plate. Doing so could cause
bodily injury. If repair is required, contact your
fire or an electrical shock.
Do not put the machine close to heating
Do not use flammable spray inside or near the
equipment. The machine cover or electric wire
machine for cleaning, etc. as gas, which fills the
may melt and it may cause fire or an electrical
interior, may ignite and cause a fire or an explosion.
Page 4 of 10
Text on page 5
Danger
Apply the power supply as specified on the
If dust forms on the prongs of the power plug,
serial plate, and independently use the wall
wipe the dust off with a dry cloth. It may cause
outlet with a rated current.
If the outlet is used concurrently with other
equipment, the branched part of the outlet
could overheat and cause fire.
Should any foreign substance, such as metal,
Do not do anything that may damage the
water, etc., get inside the machine, be sure to turn
power cord or power plug. (Do not scratch,
off the power first, and then disconnect the power
forcibly bend, twist, or pull it, or place heavy
plug from the outlet.
object on it, or bundle it.)
If the machine is used as it is, it may cause fire or
Doing so could cause a fire or an electrical
an electrical shock. Contact your dealer
When disconnecting the power plug from the outlet,
Do not unplug the power plug with wet hands.
be sure to grip the plug itself.
It may cause an electrical shock.
Pulling the power cord may damage the cord,
which could cause a fire or an electrical shock.
Be sure to turn off the power first and pull the power
Be sure to connect a ground wire.
plug from the outlet when cleaning the machine.
If an electric leak occurs, it may cause fire or
The machine may be operated by mistake, causing
Caution
When the machine will not be used for several
Place the machine on a level and stable table or
days, such as during consecutive holidays, etc.,
floor with enough space, otherwise the machine
be sure to unplug the power cord from the outlet
may fall, which could result in bodily injury.
Otherwise the insulation may deteriorate, causing
an electrical shock or fire.
Page 5 of 10
Text on page 6
Do not place the machine in a humid place or where
Be sure to remove the power plug from the outlet
it could get wet.
when moving the machine, otherwise it may
damage the cord, causing fire or an injury.
Doing so could cause the insulation to deteriorate
and cause an electrical shock or fire.
- Precautions before Use
Danger
Use only a power supply rated to match the serial plate. The jogger should have its own wall
outlet with a rated current. If the outlet is shared with other equipment, the branched part of the
outlet could overheat and cause fire.
Use the designated voltages specified in the serial plate to ensure operations under constantly
Plug the power cord directly into the wall outlet.
2-2 Environment for Use & Conditions for Storage
- A place not exposed to direct sunlight.
- A place where there is little dust and dirt.
- A place where there is little vibration.
- A place where there are no special chemicals.
Danger
Be sure to turn off the power first and pull the power plug from the outlet when cleaning the
machine. The machine may be operated by mistake, causing a bodily injury.
In order to maintain proper performance of the product, wipe off dust from time to time with a
wet cloth moistened with water or mild detergent.
Page 6 of 10
Text on page 7
Paper tray vibrates to jog paper.
Set the paper to be jogged in the tray holding the stack with its comer
This knob is used for tilting the paper tray.
While supporting the paper tray with one hand, loosen the lever and
adjust the tilting angle of the tray, and fasten the knob when the position
When this switch is turned, the paper tray jogs continuously.
When this switch is turned, the jogger blows air continuously.
Turns jogger on or off.
Power cord attaches here.
Turn left to open and turn right to close.
Page 7 of 10
Text on page 8
- How to Use
Paper tray angle adjustment
・ Holding the lower center of the paper tray head's front face, loosen the adjustment knob to
adjust the tilting angle. Then tighten it at an appropriate position.
Danger
Do not touch any revolving and/or moving part of the machine or reach a hand into the
machine. It may cause a bodily injury.
- When adjusting the tilting angle, be sure to turn the switch off and hold the lower center of the
paper tray head's front face. Do not hold the part indicated with an arrow in the photo, as it may
- Fasten the adjustment knob tightly so that it may not be loosened while the machine is in use.
Do not touch this part
Page 8 of 10
Text on page 9
- In general, for thick paper, the tilt angle is adjusted vertically and for thin paper, it is
Turn the Jogging switch to begin jogging and the Air switch for air blowing, and touch the
upper part of paper stock to help it jog neatly.
Make sure that the thickness of paper stock is less than 60mm .
- Troubleshooting
Paper is not jogging
No vibration or air
The paper size is larger than specification
Paper has static electricity
Jog it by holding with hand gently resting
on top edge of paper.
Use the air blower in addition to vibration
Too much paper loaded
Reduce size of paper stack.
Power switch is set to OFF
Set the power switch to ON
- If the fuse is blown again, an abnormality exists in the machine. Contact your dealer.
Page 9 of 10
Text on page 10
- Other Matters to Note
Caution
Be sure to remove the power plug from the outlet when moving the machine,
Otherwise it may damage the cord, causing fire or an injury.
- When moving the machine, be sure to hold the body while paying attention to the entire
balance instead of holding the paper tray or the upper part of the stand only.
- Do not apply a strong force, such as pushing or pulling, to the paper tray. Doing so might damage
- Do not place heavy objects on the machine. The object may fall, causing a bodily injury.
- Specifications
FD 402TA1
5” x 7” Min – 11” x 17” Max
110V/120V or 220V/240V, 50㎐/60㎐
110V/120V, 50/60 Hz, recommended 4A dedicated line (110V)
220V/240V, 50/60 Hz, recommended 3A dedicated line (220V)
Page 10 of 10 ยท End of manual
Quick start
- Place the jogger on a level, stable surface and plug it directly into its own grounded wall outlet.
- With the switch off, hold the lower center of the tray head, loosen the adjustment knob, set the tilt angle and tighten the knob.
- Set the paper in the tray with the stack held against its corner; keep the stack under 60mm thick.
- Turn the Jogging switch on, and the Air switch for air blowing.
- Lightly touch the top of the stack to help it jog neatly.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Paper is not jogging | Paper larger than specification, static electricity, or too much paper loaded. | Gently rest a hand on the top edge of the paper, use the air blower along with vibration, and reduce the stack size. Page 9 |
| No vibration or air | Power switch is off. | Set the power switch to ON. If the fuse blows again, contact your dealer. Page 9 |
Frequently asked questions
What paper sizes does the FD 402TA1 jog?
From 5" x 7" up to 11" x 17" (page 10).
How thick a stack can I jog?
Keep the paper stock under 60mm thick (page 9).
What power does it need?
110V/120V or 220V/240V, 50/60 Hz, with a recommended 4A dedicated line at 110V or 3A at 220V (page 10).
How should I clean the jogger?
Turn off and unplug it, then wipe off dust with a cloth moistened with water or mild detergent. Do not use flammable spray (page 6).
