Page 1 of 3
Text on page 2
Safety Devices and Other Features
Formax 8000 Series Shredders are equipped with various safety features:
When too much paper is inserted, the cutter stops operating and automatically rotates in reverse to discharge the jammed paper. An alarm sounds. Reduce the amount of paper and restart the operation.
If the door is open, the shredder will not operate.
When the shredded paper fills the wastebasket, the “FULL” light comes on and the cutter stops operation. Open the door, remove the wastebasket and empty paper scraps. Replace the wastebasket, close the door and continue operation.
FD 8300HS
Cross-Cut Paper Shredder
- If the shredder operates continuously for more than 30 minutes, the power is automatically shut off.
- If the motor is overloaded, the “STOP” LED will flash until it cools down. When the flashing stops the shredder is ready to be used again.
Oil Indicator The “MANUAL” LED will flash after every four (4) hours of operation as an indicator to oil the shredder cutting blades. The LED will continue to flash until oiled. NOTE: the shedder will still operate when the LED is flashing but at a decreased load capacity.
To oil: Spread shredder oil onto the cutters through the feed opening, and allow the oil to sit for a few minutes to permeate the cutting blades, then press the “REV” button and hold for five seconds. “MANUAL” and “REV” LED indicators on control panel will light. The shredder will operate in reverse for one minute, then the “AUTO” LED will light indicating the shredder is ready.
Maintenance
- Disconnect power by pulling power cord plug from wall outlet.
- To clean the exterior, wipe the surface with a soft cloth. If the surface is very dirty, use a neutral detergent, then wipe again with a soft cloth.
CAUTION:
- Never put water directly on the surface of the shredder.
- Never clean the case with benzene or thinner, since it will cause discoloration.
- Do not dismantle the shredder. Contact your Formax Dealer for service.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
OPERATOR MANUAL FIRST EDITION
Page 2 of 3
Text on page 3
Specifications
Safety Precautions
Cutting Style:
Shred Size:
1/32” x 3/16” (Level 6)
Sheet Capacity:
7 to 8 sheets*
Speed:
Feed Opening:
Dimensions:
Bin Capacity:
Weight:
Power Supply:
- Capacity varies depending on paper and power supply
Set-up Guidelines
- Install the shredder on a level surface, away from heat sources and direct sunlight.
- Insert plug into wall outlet with the appropriate voltage, 110V. If the outlet is shared with another electronic device, the total current should not exceed 30A (at 110V).
Operation
- Flip the power switch “ON” located on the right side of the shredder.
- Auto Start/Auto Stop When the START button is pushed, the signal lamp “AUTO” will light.
Insert paper to shred. The shredder will start and stop automatically when using this function.
To avoid personal injury, and damage to the shredder, observe the following safety precautions. Please keep these instructions for future reference.
NOTE: In case of emergency, flip the “Power Switch” to cut off power and/or pull the plug out of the wall outlet.
- Keep hands, long hair, clothing, ties, jewelry and loose items away from the feed opening and shred outlet.
- Do not use the shredder for anything other than its intended purpose. Never use it to shred cloth, plastic, cardboard or any hard material that will cause damage to the shredder blades.
- Do not allow children to use the machine.
- Do not operate with a damaged power cord or plug, or when the machine is damaged in any manner.
- Unplug the shredder when it is being moved, or if it is not in use for an extended period of time.
- Do not disconnect the power by pulling only the cord. Hold the plug when disconnecting.
- Keep the shredder away from direct sunlight.
- Do not sit on the shredder or place anything on top of it.
- Never open the fixed switch or cover.
- Manual Operation If paper is too small for the shredder’s sensors to detect, shred it manually. Push the START button once more and the “MANUAL” lamp will light. Insert paper to be shredded. Three minutes after shredding, the cutter automatically stops rotating.
- Reverse Operation Push the REV button and the signal lamp “REV” will light and cutters will operate in reverse. If too much paper is inserted at one time in standard modes, the shredder will automatically operate in reverse.
If this occurs, remove the inserted paper and shred in smaller amounts. NOTE: The maximum amount of paper to be shredded differs according to paper quality, humidity and voltage. If the shredder is to be used continuously, do not insert more than half of the maximum capacity.
- Full Sensor If the wastebasket is full, the “FULL” lamp will light and the cutter will stop automatically.
Open the door, empty the wastebasket of paper strips/chips, replace the wastebasket, close door, and continue to shred.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Page 3 of 3 · End of manual
Quick start
- Set up: Place the shredder on a level surface, away from heat sources and direct sunlight. Plug it into a 110V wall outlet.
- Power on: Flip the power switch to ON. The switch is on the right side of the shredder.
- Start auto mode: Press the START button. The AUTO lamp lights.
- Feed paper: Insert paper to shred. The sheet capacity is 7 to 8 sheets. The shredder starts and stops by itself.
- Shred small paper: If the sensors do not detect the paper, press START once more so the MANUAL lamp lights. Insert the paper. The cutter stops three minutes after shredding.
- Clear a jam: If too much paper is inserted, the shredder runs in reverse. Remove the paper and shred smaller amounts. You can also press REV to run the cutters in reverse.
- Empty the bin: When the FULL lamp lights, open the door and empty the wastebasket. Replace it, close the door and continue.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Shredder stops and runs in reverse, and an alarm sounds | Too much paper was inserted. | Reduce the amount of paper and restart. Remove the inserted paper and shred in smaller amounts. Page 2 |
| Shredder stops and the FULL light is on | The wastebasket is full. | Open the door, remove the wastebasket and empty the paper scraps. Replace the wastebasket, close the door and continue. Page 2 |
| Shredder will not start | The door is open. | Close the door. The shredder will not operate when the door is open. Page 2 |
| Power shuts off by itself | The shredder ran continuously for more than 30 minutes. | Let it rest, then restart. For continuous use, do not insert more than half of the maximum capacity. Page 2 |
| STOP LED flashes | The motor is overloaded. | Wait until the STOP LED stops flashing. The shredder is then ready to use again. Page 2 |
| MANUAL LED flashes and capacity drops | The blades are due for oil after every four hours of operation. | Spread shredder oil onto the cutters through the feed opening. Let it sit a few minutes, then hold REV for five seconds. Page 2 |
| Small paper is not detected | The paper is too small for the sensors. | Press START a second time so the MANUAL lamp lights, then insert the paper. Page 3 |
Frequently asked questions
How many sheets can the Formax FD 8300HS shred at once?
The manual lists 7 to 8 sheets. Capacity varies with paper, humidity and voltage. See page 3.
What shred size does the FD 8300HS make?
It is a cross-cut shredder with a shred size of 1/32" x 3/16" (Level 6). See page 3.
How do I oil the shredder blades?
Spread shredder oil onto the cutters through the feed opening and let it sit a few minutes. Then hold the REV button for five seconds. See page 2.
What should I not put in the shredder?
Never shred cloth, plastic, cardboard or any hard material. These can damage the blades. See page 3.
How do I clean the outside of the shredder?
Unplug it first. Wipe with a soft cloth, or a neutral detergent if very dirty. Never use water directly, benzene or thinner. See page 2.
