SAFETY MESSAGES

Your safety as well as the safety of others is important to GBC. In this Operator Manual and on the product are important safety messages. Read these messages carefully.

.Unplug the CombPRO 1000 before moving it, or when it is not In use for an extended period of time.

The safety alert symbol precedes each safety message

in this Operator Manual. This symbol indicates a

potential personal safety hazard that could hurt you or others. as well as cause product or property damage. The following warning is found on this unit:

This safety message means you could be seriously hurt or killed if you open the product and expose yourself to hazardous voltage.

CAUTION:

IN CASE OF EMERGENCY, USE THE POWER

CORD AS A MAIN OISCONNECT

DEVICE!

.Do not operate with a damaged supply cord or plug, after it malfunctions, or after it has been damaged in any manner.

.Do not overload electrical outlets beyond their capacity as this can result in fire or electrical shock.

.Do not alter attachment plug. Plug is configured for the appropriate electrical supply.

.The unit is intended for indoor use only.

.Never push objects into this product through cabinet slots. Do not spill liquid of any kind on this product.

.Do not operate if the product has been exposed to rain or water.

SERVICE

Do not attempt to service or repair the CombPRO 1000 yourself. Unplug the unit and contact an authorized GBC service representative for exchange or repair.

The following symbols appear on this product, and their meanino is as follows:

E!3PU-NCH

CLEANING

CAUTION: Unplug this product before cleaning.

Wipe exterior only with a damp cloth. Do not use detergents or solvents.

WARNING: For your protection, do not connect the CombPRO 1000 to electrical power until you read these instructions completely. Keep these instructions in a convenienIlocation for future reference. To guard against injury, the following basic safely precautions must be observed in the set-up and use of this product.

IMPORTANTSAFEGUAROS

GENERALSAFEGUAROS

.Use the CombPRO 1000 only for its intended purpose of punching and binding paper and covers according to fhe indicated specifications.

.Do not place anything in the punch opening of the machine other than paper and cover stock.

.Place unit on a secure, stable work area to prevenlIhe machine falling and possibly causing personal injury and damage to the unit.

.Follow all warnings and instructions marked on the product.

.Lift the machine from the bottom, nollhe cover.

.Do nolliflIhe machine by the cover or paper holder wire.

ELECTRICAL

SAFEGUARDS

The CombPRO 1000 must be connected to a supply voltage corresponding to the electrical rating of the machine as indicated on the serial/rating plate or in this manual.

The following notes apply only to the units rated 230V 50Hz.

MAIN CORDSET

SELECTION (FOR 230VAC MACHINES ONLY)

When choosing a detachable line cord for use with the CombPRO 1000, always observe the following.

The cordset consists of three components; the attachment plug, cordage and appliance inlet. Each of these components must meet European regulatory approvals tor safely.

The following minimum electrical ratings for the specific cordset are published for safely purposes. DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM

ELECTRICAL

REQUIREMENTS.

PLUG: 3A, 250 volts, 50/60 Hz, Class 1,3 conductor, European safely agency approved.

CORDAGE:

Type H05W-F3GO.75, Harmonized ( <j HAR t> ). The" <j 1:>" symbols indicate cordage approved to appropriate European standard (NOTE: "HAR" may be substituted by the approval mark of the European safely agency which approved the cordage. An example would be" <jVDE t>".

APPLIANCE

CONNECTOR: 3A, 250 volts, 50/60 Hz, European safely approved, Type IEC 320. Cordset shall not exceed 3 meters in length. Cordset with component electrical ratings greater than the minimum specified electrical ratings may be substituted.

i\ CAUTION: THE POWER RECEPTACLE MUST BE LOCATED

...NEAR THE EQUIPMENT

AND BE EASILY ACCESSIBLE.