Text on page 1
GBC Pinnacle 27 EZ Load 27" Thermal Roll Laminator - 1701720EZA Instruction Manual
Page 1 of 5
Page 2 of 5
Text on page 3
GBC Pinnacle 27- Roll Laminator
Page 3 of 5
Page 4 of 5
Page 5 of 5 · End of manual
Quick start
- Power on: move the main power switch to ON (I), then use the standby switch on the control panel to activate the laminator.
- Pick settings: use the lamination guide on the feed table to choose temperature and speed for your film gauge and media.
- Warm up: wait for the green READY indicator to light (warm-up is 8–10 minutes).
- Run: place items on the feed table, push RUN/STOP to Run, and slide them into the nip rollers.
- Stop: when the laminated items exit the rear, push RUN/STOP to the Stop position.
- Trim: use the rear slitter at the back of the laminator to separate items from the film web.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Power indicator does not light when Standby is pushed | Main power switch is OFF, the unit is not connected to power, the circuit breaker has opened, or the feed table latches are not in position | Move the main power switch to ON (I), plug into an appropriate receptacle, reset the circuit breaker, or move the feed table latches into position. Page 5 |
| Laminated items are wrinkled | Insufficient film tension | EZload: the film holder lever is not closed, so close it. Non-EZload: adjust the film brake tension. Page 5 |
| Laminated items are wavy | Excessive heat | Select the appropriate heat setting. Page 5 |
| Laminated items are cloudy | Insufficient heat | Select the appropriate heat setting and wait for the ready light to come on. Page 5 |
| Unsatisfactory adhesion to media | Insufficient heat, or media not suitable for thermal lamination | Select the appropriate heat setting and wait for the ready light. The composition or finish of the media may not be compatible with thermal lamination. Page 5 |
| Film jam (wrap-up) around the roller | The laminator is not positioned so exiting film can drop freely to the floor | Push RUN/STOP to Stop, remove the feed table and heat shield, cut the film webs, and pull the loose ends straight out. Reinstall the feed table, push REVERSE to guide the film out, release it once the film clears the heat shoes, then rethread. Page 5 |
Frequently asked questions
What temperature and speed should I use on the Pinnacle 27?
The lamination guide lists Nap I at 150°C/300°F for 1.5 mil (38 mic) film at speed 1–10 and 3 mil (75 mic) at speed 1–5. Nap II at 120°C/250°F covers 1.7 mil (42.5 mic) at speed 1–10 and 3 mil (75 mic) at speed 1–5. The chart is for reference only. See page 5.
What are the Pinnacle 27 specifications?
Dimensions are 536 x 900 x 350 mm (W x L x H). Net/gross weight is 46/52 kg. Power is 120V 60Hz, 12A, 1580W, with an 8–10 minute warm-up and 2 mm maximum thru-put thickness. Speed ranges 1.4 m/4.6 ft to 3.6 m/11.8 ft. See page 5.
Does the Pinnacle 27 shut off automatically?
Yes. The laminator shuts down after two hours of inactivity. Press STANDBY with the main switch ON to wake it, and use the Auto Shut-Off Selector to enable or disable the feature. See page 4.
How do I clean the heat shoes?
Remove the film, preheat until the READY lamp lights, and clean the top and bottom heat shoes with a soft cloth. Do not use metal scouring pads. See page 3.
Why is adhesive building up on the heat shoes and rollers?
This happens when only one roll of film is used, or when one or both rolls run off the core. Always use both top and bottom rolls. See page 5.
