Text on page 1
GBC Pro-Trim Lamination Trimmer
Instruction Manual
For Models: GBC Pro-Trim 45 Trimmer GBC Pro-Trim 63 Trimmer
Page 1 of 11
Page 2 of 11
Text on page 3
- Included parts and tools
Box:
ProTrim 45 ProTrim 63
Unit:
ProTrim 45 ProTrim 63
Cutting Specifications:
Maximum Cut Length: ProTrim 45 = 45” ProTrim 63 = 63”
Page 3 of 11
Text on page 4
Included Parts and Tools
Mid cross member (Distinguishable by rounded edges)
Upper cross member (Distinguishable by squared edges)
Legs ( Left & Right)
Page 4 of 11
Text on page 5
Included Parts and Tools
Bolts, Qty 4. ( Used to secure the legs to the upper cross member)
Bolts, Qty 2, ( Used to secure waste curtain shaft to stand)
Bolts, Qty 4. ( Used to secure the mid cross member to the legs)
Bolts, Qty 4. ( Used to secure the trimmer assembly to the stand)
Hex Tool ( Includes one of the following sizes 6mm, 5mm, & 4mm)
Page 5 of 11
Text on page 6
Assembly
Begin by finding the two legs and the upper cross member. The legs must be oriented correctly so that the larger holes are on the outside of the unit. The smaller hole must be facing toward the inside of the unit.
Lay the upper cross member on the floor, then align one of the legs with the end of the cross member so the bolts can be inserted through the leg and into the upper cross member. Use the bolts identified as ( A ) in the hardware section to secure the leg to the upper cross member. The 5mm Hex tool should be used on these bolts. Once completed, repeat this step on the other leg.
Page 6 of 11
Text on page 7
Assembly
Place the stand on its feet. Attach the mid cross member to the stand with the bolts identified as “ C “ in the hardware section of this manual. Use the 6mm Hex tool for these bolts.
The stand should now be completed. Two people are required for the next step. With one person on each side of the trimmer assembly, carefully pick it up while keeping it level to prevent the cutter head assembly from moving. Place the trimmer assembly on top of the stand.
Page 7 of 11
Text on page 8
Assembly
Use the bolts identified as “ D “ in the hardware section to secure the trimmer assembly to the top of the stand. Use the 6mm Hex tool for these bolts.
Remove the wire ties from the waste curtain, and then install the waste curtain in the rear of the trimmer as shown in the photo.
Page 8 of 11
Text on page 9
Assembly
Attach the other waste curtain support bar to the stand of the trimmer with the bolts identified as “ B “earlier in this manual.
The assembly of the trimmer is now complete.
Page 9 of 11
Text on page 10
Operation
The GBC ProTrim 45 and ProTrim 63 were designed with ease of operation in mind.
The steps for proper operation are as follows:
1.) Move the cutter head all the way to the right or left side of the trimmer. (This is required because the paper clamp applies slight pressure to the print when the cutter head is not all the way to one side of the unit.)
2.) Insert the print to be trimmed.
3.) Adjust the edge guide as necessary to aid in squaring the print.
4.) Use the paper clamp as an aid to determine where the cut will be made in the print. Support the print with one hand; use your other hand to slide the cutter head across the trimmer to make the cut.
5.) Remove the trimmed pieces from the waste curtain as necessary.
Page 10 of 11
Page 11 of 11 ยท End of manual
Quick start
- Build the stand: lay the upper cross member on the floor and attach each leg with the A bolts, using the 5mm hex tool. The larger holes go on the outside.
- Finish the stand: stand it on its feet and attach the mid cross member with the C bolts, using the 6mm hex tool.
- Mount the trimmer: with two people, lift the trimmer assembly level and place it on the stand. Secure it with the D bolts and the 6mm hex tool.
- Add the waste curtain: remove the wire ties, install the curtain in the rear, and attach the support bar with the B bolts.
- Trim: move the cutter head all the way to one side, insert the print, adjust the edge guide, and slide the cutter head across to cut.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Legs do not line up with the cross member | Legs are oriented wrong. | Position the legs so the larger holes are on the outside and the smaller hole faces the inside. Page 6 |
| Cannot tell the cross members apart | Two cross members are included. | The mid cross member has rounded edges and the upper cross member has squared edges. Page 4 |
| Not sure which bolts go where | Bolts come in four groups. | Use 4 bolts for legs to upper cross member, 2 for the waste curtain shaft, 4 for mid cross member, and 4 for the trimmer assembly. Page 5 |
| Cutter head moves while lifting the trimmer | The assembly was not kept level. | Use two people, one on each side, and keep it level. Page 7 |
| Wrong hex tool for a bolt | The hex tool includes 6mm, 5mm and 4mm sizes. | Use the 5mm hex tool on the A bolts and the 6mm hex tool on the C bolts. Page 6 |
| Paper clamp presses on the print | The cutter head is not all the way to one side. | Move the cutter head fully to the right or left before inserting the print. Page 10 |
Frequently asked questions
What parts and tools are included?
Legs (left and right), mid and upper cross members, bolts, and a hex tool with 6mm, 5mm and 4mm sizes. See page 4, page 5.
How many people are needed to assemble it?
Two people are needed to place the trimmer assembly on the stand. See page 7.
How do I use the trimmer?
Move the cutter head to one side, insert the print, adjust the edge guide, and slide the cutter head across. See page 10.
Which models does the operation section cover?
The GBC ProTrim 45 and ProTrim 63. See page 10.
