

Page 1 of 4

Text on page 2
4.0 OPERATING INSTRUCTIONS
- Check the bind edge guide alignment by inserting a receiving strip in the strip recess area. Lay a sheet of correctly aligned punched paper on the strip, matching up the holes and the strip so that the strip is not showing at the top or bottom of the paper. Adjust the bind edge guide if necessary by loosening the screw and sliding the guide to the edge of the paper.
- Place the back cover (face down), the punched sheets (last page on the bottom), and front cover (face up) on top of the receiving strip.
- Place the receiving strip (bottom binding strip with holes), textured side down in the strip recess, located in front of the backstop. Be sure the small hole in the receiving strip is over the locating pin. The locating pin is on the left hand side of the strip recess area in front of the backstop. The locating pin fits into the small hole in the plastic strip. The strip is positioned correctly over the locating pin when it is difficult to slide the strip to the right. Failure to properly align the strip can cause machine damage.
- Now determine the correct size of the pin strip. Use the scale on the backstop to determine the thickness of the document and the size of the pins required. 1 inch (25 mm) on the scale requires a 1 inch (25 mm) pin. Anything over 1 inch (25 mm) requires a 2 inch (51 mm) pin. Anything over 2 inches (51 mm) requires a 3 inch (75 mm) pin. The pins should extend all the way through the document but not more than 1 inch (25 mm) beyond. Insert the strip through the document's holes and the receiving strip.
Page 2 of 4

Text on page 3
4.0 OPERATING INSTRUCTIONS
- Turn the machine on, and the "Wait" light will be on. The machine takes about 45 seconds to warm up, and the "Wait" light to go off.
- Use the selector button to identify whether the document is less than or greater than 1 inch (25 mm). The machine will automatically vary the binding speed to make the most secure bind.
- Begin the binding process by pulling the pressure bar toward you and lowering it on top of the document. To prevent jamming problems, lower the bar onto the document rather than "drop" it.
- The binding cycle will start automatically, and the pressure bar will return to its original position when the cycle is complete.
- Remove the bound document.
Page 3 of 4

Text on page 4
OPERATING INSTRUCTIONS
- Place document to be debound as follows: bound edge against the backstop, small hole in bottom strip over locating pin, edge of document next to bind edge guide.
2 Once the document to be debound is properly located, depress the Bind/Debind selector to place machine in debind mode.
3 Lower the pressure bar onto document, and the machine will go through the debinding cycle.
- Immediately after pressure bar raises (approximately 12 seconds), remove the document and peel the top strip off.*
- NOTE: If you do not perform this step quickly enough, it will be too difficult to remove the strip. Put the document through the debind process again and remove the strip faster this time.
Page 4 of 4 · End of manual
Quick start
- Check the bind edge guide with a receiving strip and a punched sheet; adjust the guide so the strip does not show at the top or bottom.
- Place the receiving strip textured side down in the strip recess, with its small hole over the locating pin on the left.
- Stack the back cover (face down), punched sheets and front cover (face up) on the receiving strip.
- Use the backstop scale to pick the pin strip: up to 1" needs a 1" pin, over 1" a 2" pin, over 2" a 3" pin. Insert it through the document and receiving strip.
- Turn the machine on and wait about 45 seconds for the Wait light to go off.
- Set the selector for a document under or over 1" (25 mm).
- Pull the pressure bar toward you and lower it gently onto the document; the cycle starts automatically.
- When the pressure bar returns, remove the bound document.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Pressure bar jams | The bar was dropped onto the document instead of lowered. | Lower the pressure bar onto the document rather than dropping it. Page 3 |
| Top strip is too hard to peel off after debinding | The strip was not removed quickly enough after the pressure bar raised. | Run the document through the debind cycle again and peel the top strip off immediately after the bar raises (about 12 seconds). Page 4 |
| Risk of machine damage when binding | The receiving strip is not aligned on the locating pin. | Make sure the small hole in the receiving strip is over the locating pin; it is seated correctly when the strip is hard to slide to the right. Page 2 |
Frequently asked questions
Which pin strip length do I need?
Measure the document on the backstop scale. Up to 1" (25 mm) uses a 1" pin, over 1" uses a 2" (51 mm) pin, and over 2" uses a 3" (75 mm) pin. Pins should go all the way through but not more than 1" beyond. See page 2.
How long does the System Four take to warm up?
About 45 seconds. The Wait light goes off when it is ready. See page 3.
Can the System Four debind a document?
Yes. Place the bound edge against the backstop with the small hole over the locating pin, press the Bind/Debind selector, lower the pressure bar, and peel off the top strip right after the bar raises. See page 4.
What does the thickness selector do?
It tells the machine whether the document is under or over 1" (25 mm), and the machine varies the binding speed for the most secure bind. See page 3.
