Page 1 of 4
Text on page 2
PLASTIC/WIRE
BINDING SYSTEM
SYSTEME DE RELIURE PLRSTIOUE ET METALLIOUE
SISTEMA DE ENCUADERNRCION: PLAsTICD Y METALICO
Important: Please read these instructions as it will only take you a few minutes. Important: Veuillez prendre quelques minutes pour lire ces instrucitons. Importante: Rogamos tomarse unos minutos para leer estas instrucciones.
Page 2 of 4
Text on page 3
PUNCHING
I PERFORATION
I PERFORACI6N
BINDING PLASTIC / RELIURE PLASTIQUE / ENCUADERNAR CON pLAsTIco
BINDING WIRE I REUURE METALUQUE I ENCUADERNAR CON MET Auco
Page 3 of 4
Text on page 4
HITECH'"
OPERATION
MANUAL
AND
SPECIFICATIONS
WARRANTY
REGISTRATION
Punch Place up to 10-12 sheets of paper, or 1-2 covers into punch channel and align them against the rear of punch channel and paper stop. Pull handle down to punch.
BINDING
WITH PLASTIC COMBS
- Insert and Open Plastic Comb Insert plastic comb behind metal rake with open side up. Slide it to the right to engage Push binding lever slowly to open comb.
- Bind Plastic Insert document vertically into plastic comb with its cover facing you. Lay document down flat and return binding lever to original position Slide document to the left
INSTALLATION
AND SET-UP Carefully unpack and inspect your new IBICO plastic and wire binding machine for shipping damage. If any damage is noticed it should be brought to the immediate attention of the delivery carrier.
The following instructions will demonstrate certain methods and techniques to improve your binding results. Before using the machine carefully read through these instructions.
This machine is designed to punch up to 12 sheets of common photocopier paper. Cover materials vary in thickness and composition; as a rule, covers should be punched two at a time separate from the document. Some brands of clear plastic covers and sheet protectors do not punch cleanly and may jam the machine All IBICO cover materials are manu1actured to punch cleanly in any IBICO machine.
PUNCHING
1. Open Machine Lilt up both operating levers until they click together as handle. Fold out suppor legs as shown. 2. Select Comb Size Pull handle down, slide document into the front of shaft, and move handle back Now read comb size as indicated on blue scale (left side) behind your document. 3. Set Paper Stop (side guide) For proper punch alignment, press down blue paper stop and move it to the line indicated for your paper length (51/2" (139,7mm), 8 1/2" (215,9mm), 11" (27g,4mm),111/4" (285,7mm), orA4).Align RIGHT edge of blue paper stop with selected line. Push it up to secure
Note: Sheets can be replaced or added, simply by placing bound materials into metal rake, and reversing steps 1 and 2.
BINDING
WITH WIRE COMBS 1. Insert Wire Comb For cleanest bound look, hide binding closure by placing the front and rear covers back to back on top of front cover. Insert wire comb of selected size into punched holes. 2. Bind Wire Insert document with wire into the back of shalt. Hold document firmly with open part of wire facing downward. Pull handle down slowly until selected comb size appears on the right side. Closed wire comb should be round in shape. Its upper and lower teeth should meet, but not pass or cross each other. Return handle to upright position. Remove bound document.
REMOVING
PUNCHING WASTE Pull tray drawer to the right and remove from base of machine Empty waste and return drawer to original position.
Page 4 of 4 · End of manual
Quick start
- Lift both operating levers until they click together as a handle and fold out the support legs.
- Check the comb size: slide the document into the front of the shaft with the handle down and read the blue scale on the left.
- Set the blue paper stop to the line for your paper length (5 1/2", 8 1/2", 11", 11 1/4" or A4).
- Place 10-12 sheets or 1-2 covers in the punch channel against the rear and paper stop, then pull the handle down to punch.
- For wire: place the front and rear covers back to back on top of the front cover and insert the wire comb into the holes.
- Insert the document with the wire into the back of the shaft, open side down, and pull the handle slowly until the comb size shows on the right.
- Return the handle upright and remove the bound document.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Punch jams on covers | Some clear plastic covers and sheet protectors do not punch cleanly. | Punch covers two at a time, separate from the document. Page 4 |
| Wire comb closed incorrectly | Handle not pulled to the selected comb size. | A closed wire should be round, with upper and lower teeth meeting but not crossing. Close slowly until the selected size appears on the right. Page 4 |
Frequently asked questions
How many sheets can the W200 punch at once?
Up to 10-12 sheets of photocopier paper or 1-2 covers. See page 4.
Can the W200 bind with plastic combs?
Yes. Insert the comb behind the metal rake open side up, slide it right, push the binding lever to open it, then hang the document on the comb and return the lever. See page 4.
How do I know a wire comb is closed correctly?
It should be round, with the upper and lower teeth meeting but not passing or crossing. See page 4.
How do I empty the punch waste?
Pull the tray drawer to the right out of the base, empty it and slide it back. See page 4.
