Page 1 of 3
Text on page 2
Message Center
Instruction Sheet
For the most secure mounting of the unit, install all mounting screws directly to wall studs. When wall studs can not be used we recommend using hollow wall anchors.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
The recommended mounting height of the unit is 78" from the floor to the top of the unit.
Mounting Instructions: 1.) Scribe a level line on the wall at 76-7/16" 2.) Space the holes using the attached charts. 3.) Drill and install the mounting hardware and allow the screw head to protrude 1/4" max from the wall. 4.) Hang unit onto protruding screw heads using the sheet metal brackets on the rear of the unit.
WIDTH
HEIGHT
NOTE: To mount a 96" long unit, use the "L"-hangers (provided) in addition to wall anchors (not provided) and follow the mounting instructions enclosed with the "L"-hangers.
DETAIL A
78" REF.
NOTE: For permanent mounting, drill a 1/8" hole through the back of the sheet metal brackets. The hole should be located at 1-5/16" vertical & 2-5/16" horizontal. Fasten to the wall with 2" #8 self-tapping screws. (Before drilling through the face of the board make sure to score the board surface so that it doesn't get tangled in the screw.)
FLOOR LINE
Unit Width
Unit Height
- *Important**: Units with lighted headers require electrical installation by a licensed electrician. Consult your local electrical code to determine the correct method of installation.
The lamps have been mounted in the unit, but have not been wired. Access to the lamps can be made by removing the rear panel of the header section of the unit.
- *Important**: Specific u nits that are designed for outdoor use are water-resistant, not water-proof. When being hung outdoors, unit should be under cover to prevent damage.
ISMCT9709 10-14
Page 2 of 3
Text on page 3
Message Center
Gently tap corner with door open.
MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920
Your new Ghent Message Center has been assembled and inspected to Ghent's high quality standards. Occassionally during shipment, your message center's door(s) may shift. This shift results in an uneven gap between the door(s) and the body of your unit. The uneven gap is easily remedied. Mount your unit per the instructions on page 1. Then simply open the affected door(s) and gently tap the door corner opposite the largest gap (see the figure above). When you tap the door, be sure to use a rubber mallet or a block of wood and a hammer so the door's finish is not marred. After you've tapped the door corner, close the door and inspect the surrounding gap. If needed repeat the tapping procedure.
ISMCT9709 10-14
Page 3 of 3 · End of manual
Quick start
- Scribe a level line on the wall at 76-7/16" for a unit top at the recommended 78" from the floor.
- Space the holes using the charts for your unit width.
- Drill and install the mounting hardware, leaving screw heads protruding no more than 1/4" from the wall.
- Hang the unit on the screw heads using the sheet metal brackets on the back.
- For permanent mounting, drill a 1/8" hole through each bracket (1-5/16" vertical, 2-5/16" horizontal) and fasten with 2" #8 self-tapping screws.
Frequently asked questions
What is the recommended mounting height?
78" from the floor to the top of the unit (page 2).
How do I mount a 96" long unit?
Use the provided L-hangers along with wall anchors (not provided), following the L-hanger instructions (page 2).
Do lighted header units need an electrician?
Yes. The lamps are mounted but not wired, and must be installed by a licensed electrician to local code (page 2).
Can the message center be used outdoors?
Outdoor models are water-resistant, not waterproof, and should be hung under cover (page 2).
How do I fix an uneven gap around the door?
After mounting, open the door and gently tap the corner opposite the largest gap with a rubber mallet or a wood block and hammer, then close and check; repeat if needed (page 3).
