Text on page 1
- Wilson 42" High Black Tuffy Utility A/V Cart with Cabinet and Pullout Shelf (3-Shelf Black Legs)
Page 1 of 6
Text on page 2
3 Shelf Tuffy Cart Instructions
NOTICE:
Leg lengths of leg E may be shorter than leg F
- - Rubber Mallet
Optional fluted legs for units with cabinet pack
Install optional cabinet pack / pullout shelf / locking drawer assembly after step 1
Page 2 of 6
Text on page 3
Pullout Keyboard Shelf Instructions
FR x1
- - Phillips Screwdriver
FL x1
NOTICE:
Size and style of the plastic ribbed shelf may vary by model number.
(Ha
Take the top shelf of your plastic cart and lay it flat. Collect parts: FL, FR & A. Align FR & FL to the outer holes at the top of the shelf. Take screw A and fasten with a screwdriver, do not tighten fully until keyboard is attached.
Collect parts: H. Align the pullout shelf H runner so that the runner snaps into place into the FL & FR brackets. Pull the shelf out to make sure it is fully seated. Tighten screws A. Pullout keyboard shelf assembly is now complete.
Page 3 of 6
Text on page 4
Side Pullout Shelf Instructions
- - Phillips Screwdriver
Lay the top shelf of your Tuffy cart upside down and Install the four legs intended for this shelf.
Slide and align runner H & G onto the legs and tighten screw N with a screwdriver.
IMPORTANT:
Install optional front pullout shelf BEFORE step 2
Take pullout shelf K and bracket L and screw together into the unfinished surface of shelf K with screw M.
Mount pullout shelf K to runner H & G so that the edge of the shelf snaps into the runner hooks.
You have now completed your pullout shelf.
Page 4 of 6
Text on page 5
Tuffy Cart Cabinet Pack Instructions
Please consult your Tuffy cart base unit instructions before starting
IMPORTANT: Flip shelf B, and lock the 2 locking casters D before assembling the unit.
- - Rubber Mallet
Page 5 of 6
Text on page 6
Electric Assembly Instructions
Number of outlets may vary.
(Plastic or Metal Mounting Surface)
Push screw C through electric outlet A. Make sure the electric outlet A and cord wrap B align with the mounting surface screw holes. Push screw C through cord wrap B and the mounting surface screw holes. Use wing nut D and screwdriver to fasten.
Page 6 of 6 · End of manual
Quick start
- Have a rubber mallet and a Phillips screwdriver ready.
- Assemble the 3-shelf base cart, noting that leg E may be shorter than leg F. Install the cabinet pack and pullout shelf after step 1.
- For the keyboard shelf, align brackets FL and FR to the outer holes at the top of the top shelf and fasten with screws A, leaving them loose.
- Snap the runner of pullout shelf H into the FL and FR brackets, pull the shelf out to seat it fully, then tighten screws A.
- For the cabinet pack, flip shelf B and lock the 2 locking casters D before assembling.
- Mount the electrical outlet and cord wrap to the mounting surface with screw C and wing nut D.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Two legs look different in length | Leg E may be shorter than leg F. | This is expected. Leg lengths of leg E may be shorter than leg F. Page 2 |
| Cabinet pack, pullout shelf or drawer will not fit | The optional part was installed at the wrong step. | Install the optional cabinet pack, pullout shelf or locking drawer assembly after step 1. Install the optional front pullout shelf before step 2 of the side pullout shelf instructions. Page 2 |
| Pullout keyboard shelf wobbles or does not slide right | The runner is not seated in the brackets or the screws are loose. | Snap runner H into the FL and FR brackets. Pull the shelf out to check it is fully seated, then tighten screws A. Page 3 |
| Keyboard will not attach to the pullout shelf | Screws A were tightened fully too early. | Do not tighten screws A fully until the keyboard is attached. Page 3 |
| Cabinet unit rolls during assembly | The casters are not locked. | Flip shelf B and lock the 2 locking casters D before assembling the unit. Page 5 |
| Electric outlet does not line up with the mounting surface | The outlet and cord wrap holes are not aligned. | Make sure outlet A and cord wrap B line up with the mounting surface screw holes. Push screw C through and fasten with wing nut D. Page 6 |
Frequently asked questions
What tools do I need?
A rubber mallet for the cart and cabinet pack, and a Phillips screwdriver for the pullout shelves (page 2-5).
Why is one set of legs shorter than the other?
That is expected: leg E may be shorter than leg F. Check which legs you are using for each shelf before assembling (page 2).
How do I install the pullout keyboard shelf?
Lay the top shelf flat, fasten brackets FL and FR to the outer holes with screws A (not fully tight), snap the shelf H runner into the brackets, pull it out to seat it, then tighten the screws (page 3).
What should I do before assembling the cabinet pack?
Flip shelf B and lock the 2 locking casters D (page 5).
How do I attach the electrical outlet?
Push screw C through the outlet and the cord wrap, line both up with the screw holes on the mounting surface, push the screw through, and fasten with wing nut D using a screwdriver. The number of outlets may vary (page 6).
