Page 1 of 5
Text on page 2
Esealer
Impulse
Specifications
Operating Instruction
Tish-100 Tish-400
Model Tish-200 Tish-300
Model:Tish-100
Surce 110V/220V 110V/220V 110V/220V 110V/220V
Tish-200
Impulse Power 600W 180W 430W/450W 330W
Tish-300
MAX.SEALLENGTH 400mm 100mm 200mm 300mm
Tish-400
MAX.SEALTHICKNESS 0.4mm 0.3mm 0.3mm 0.4mm
Tish-200C
HEAT TIME 0.2~1.3(sec) 0.2~1.3(sec) 0.2~1.3(sec) 0.2~1.3(sec)
Tish-300C
1.7kg 4.5kg 5.2kg
Weight
Dimensions
Model Tish-200C Tish-300C
Surce 110V/220V 110V/220V
Impulse Power 430W/450W
200mm 300mm
Max.Seallength
MAX.SEALTHICKNESS 0.4mm
Heat Time
3.7kg 5.0kg
Weight
Dimensions
Tew Te We Le Ltr Iche Listed 34J9
Printed In Taiwan
Page 2 of 5
Text on page 3
Parts Identification
Pressure Plate Handle Knob Cutting Blade Bracket Handl Knob
Hinge Pin Platen Spring
Handle Rubber Cutting Blade
Rubber Pressure Pad Hinge Pin
Heater Insulalion Hinge Brackel
Bag-Fixing Plate Heating Element
TEW "Enclosure
Upper Cloth MetalPlate
PilotLamp Strain Relief Bushing
Heater Insulation Timer Knob
Variable Resisfor Control Panel Metal Plate Control Panel
Body Casting
Power Supply Cord Heating Element Power Supply Card
Pilot Lamp Timer Knob
Page 3 of 5
Text on page 4
Connection Diagram
Heating Element
Rubber Foot
Transformer
- Timer Connector Plug nter nal Wiring RELAYDC24V
Printed Circuit Board
Pilotlamp
Source
Timer
Micro Switch
Heater Transformer CONTROLP.C.B. CONNECTORL
Purpose
These Impulse Sealers TIsH-100 TISH-200C
- 200 300C
Cover Plate
Grounding Wire
are the perfect sealers forPEand Ppbagsto package various kinds of candy.foodstuff,general
Heater Terminal Assembly Micro Switch Lever Micro Switch Lever Spring
Characteristics
MicroSwitch Insula fi on Plate
- CONVENIENTANDCOMPACTINSIZE
- USES ENERGYONLY WHEN SEALING
- PRECISION ELECTRONIC CONTROL CIRCUIT
- DESIGNED TO BEEASYTO USE
Page 4 of 5
Text on page 5
Operation Heating Time Adjust
Thismachine doesnotuseapowerswitch.PlugtheACcordinto
the powersource,Set the timer knob according to the thickness SCALE
1-2 5-6 7-8
Range
Model
ofthematerialstobesealed.Thehigherthenumberon thedial
Tish-100
0.05mm 0.1mm 0.2mm 0.3mm
sealingplatform,andthenpushdownthehandle.Theelectronic TISH-300
300C 0.15mm 0.08mm 0.3mm 0.4mm
circuit controls the heat time automatically.thelightturnsoff（to 400
(SETTINGFORPE BAGS)
handle.The perfect seal iscomplete.
Incaseofabreakorifdamageappearsontheseal,itisbecause NOTES oftoolongaheatingtime.Adjustthetimerknobtowardthe
direction of a lower number for a shorter heating time.
Anon-tightseal is caused by too short a heating time.Adjustthe residual on the platform which will reduce the life of theheating timer knob toward the direction of a higher number for a longer element and of the heat-resisting teflon. heating time. Do not use water to clean the sealing platform
Should the bottom tefloncloth wearout,it will causeashort circuit and damage the heating element,Each timeyou replace
it means the cooling time should be longer,Keep thehandle the heating element orthe top teflon,check the bottom teflon, down for a short time after the light turns off. Replace it with a new bottom teflon if the old one is worn.
Slide the knife to cutoff the rest A worn silicon handle rubber will influence the sealing effect.
After a long period of usage,it should be checked.
of the bag.
Spare Parts
After the timer knobhas been set,the heat time duration will
Model Tish-100·200·300·400|Tish-200C·300C
Heating Element
adjustments for continuous sealing. 2PCS 2PCS
Upper Cloth 2Pcs 2Pcs
It is okay to leave the ACCord plugged into the power source CUTTING BLADE 1PCS No poweris used unless the handle is pressed down.
Page 5 of 5 · End of manual
Quick start
- Plug in: This machine has no power switch. Plug the AC cord into the power source.
- Set the timer: Set the timer knob for the thickness of the material to be sealed. A higher dial number means a longer heating time.
- Place the bag: Place the bag on the sealing platform.
- Seal: Push down the handle. The electronic circuit controls the heat time automatically.
- Wait for the light: Keep the handle down for a short time after the light turns off so the seal can cool.
- Release: Lift the handle. The seal is complete.
- Cut if needed: On models with a knife, slide the knife to cut off the rest of the bag.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Seal is broken or the film is damaged | The heating time is too long. | Turn the timer knob toward a lower number for a shorter heating time. Page 5 |
| Seal is not tight | The heating time is too short. | Turn the timer knob toward a higher number for a longer heating time. Page 5 |
| Seal opens before it cools | The cooling time is too short. | Keep the handle down for a short time after the light turns off. Page 5 |
| Short circuit or damaged heating element | The bottom Teflon cloth is worn out. | Check the bottom Teflon each time you replace the heating element or the top Teflon. Replace the bottom Teflon if it is worn. Page 5 |
| Weak sealing effect | The silicone handle rubber is worn. | Check the rubber after a long period of use and replace it if it is worn. Page 5 |
| Shorter life of the heating element and Teflon | Residue builds up on the sealing platform. | Keep the platform clean. Do not use water to clean it. Page 5 |
Frequently asked questions
Does this impulse sealer have a power switch?
No. Plug the AC cord into the power source. No power is used unless the handle is pressed down. See page 5.
Can I leave it plugged in?
Yes. The manual says it is okay to leave the AC cord plugged in. No power is used unless the handle is pressed down. See page 5.
How do I set the timer?
Set the timer knob by the thickness of the material. A higher number on the dial gives a longer heating time. See page 5.
What bags can it seal?
The manual says these sealers are for PE and PP bags used to package items like candy and foodstuff. See page 4.
How do I clean the sealing platform?
Keep it free of residue. Do not use water to clean it. See page 5.
