

Page 1 of 31

Page 2 of 31

Text on page 3
Welcome to the World of Drytac
Over the past three decades, Drytac has evolved into one of the world‟s most highly regarded manufacturers of products for graphics finishing and display. Our core product line consists of a wide range of pressure-sensitive, heatset and thermal overlaminating films. In addition, we offer an extensive line of mounting adhesives, backing films, inkjet media, finishing equipment, accessories, and banner stands.
Our Start To Finish strategy sums up Drytac‟s unique ability to manage all phases of the customer experience: product quality and performance, manufacturing and distribution, training and technical support and the industry‟s best customer service.
Jet Mounter™ Professional Quality Entry-Level Models JM 18 and JM26
These solid mid-size models deliver superior results for beginners and experienced users alike. Easy to set up and operate, the JM18‟s and JM26‟s are widely used by photography studios, picture framers, digital art studios and other creative shops. Standard features include: all-steel construction, variable speed electric drive, forward and reverse, foot pedal control, silicon rollers, photo-electric safety stop and supply shaft.
Since the JM18 has many of the same features as the JM26 consider the references in this manual pertaining to the JM26 are applicable to the JM18.
Jet Mounter™ Wide Format Laminators
Drytac‟s Pressure-Sensitive Cold-Mount Models deliver economy and versatility for graphics finishing.
The JetMounter™ motorized laminator series is engineered by Drytac to deliver a combination of performance and value unequalled in the finishing industry. Compatible with any pressuresensitive overlaminating film. JetMounters are also ideal for permanently mounting graphics onto cardstock, foam board, MDF or rigid PVC board.
All electric models include: variable-speed electric drive, silicone rollers, all-steel construction, forward and reverse, supply shaft, foot pedal and photo-electric safety stop.
These three heavy-duty wide-format models,( JM44,JM54,and the new JM63) are the culmination of our three decades in the mounting and laminating business. Equipped with the performance features our customers demand, JetMounter wide format models are unmatched for value.
Page 3 of 31

Text on page 4
Important Safety Information ...............................................................................5
Specific Moving Instructions .........................................................................9
Unpacking and Installation ...........................................................................10,11
Setting Roller Pressure .................................................................................14
Adjusting Shaft Tensions ..............................................................................15
Mounting With the JetMounter Series Laminators Mounting Board Selection ............................................................................16
Pre-coating the Mounting Board ...................................................................17
Mounting a Graphic to a Pre-Coated Board .................................................18
Laminating with the JetMounter Series Laminators Selecting a Laminate Film ............................................................................19
Single Mounted Graphic ...............................................................................21
Laminating Multiple Mounted Images ...........................................................22
Using a Leader Board ...................................................................................23
Preparing Mounting Boards ..........................................................................24,25
Care and Maintenance ..........................................................................................26
B Revision Functional Requirements ............................................................31
Page 4 of 31

Text on page 5
Important Safety Information
Before operating this equipment for the first time, it is crucial that you take the time to
read and understand all of the following safety-related information. Failure to follow
these procedures could result in serious personal injury and/or damage to the equipment
Safety Signal Words and Symbols
Danger headings indicate imminently hazardous situations that, if not avoided, will result in
serious injury or death.
Pinch Hazard Inside Panel
Warning headings indicate a potentially hazardous situation that, if not avoided, could result in
severe injury or death.
Page 5 of 31

Text on page 6
Caution headings indicate a potentially hazardous situation that, if not avoided, may result in
minor or moderate injury.
This symbol indicates a statement of company policy directly or indirectly related to the safety of
personnel or protection of property.
Pinch Hazard Inside Panel
Pinch point. Keep hands clear during operation.
These symbols indicate a dangerous pinch hazard exists.
This caution label indicates that a heavy object is involved and assistance is needed to avoid
performs mounting and laminating using two rollers to apply uniform
pressure to adhesives and overlaminating films. The point where the rollers touch the material is
called the Nip. This area creates a potential pinch hazard for fingers or other objects. DO NOT
OPERATE THIS EQUIPMENT IF YOU ARE UNWILLING TO ACCEPT THIS HAZARD! TO
AVOID INJURY, ALWAYS KEEP YOUR FINGERS AWAY FROM THE NIP AREA.
Page 6 of 31

Text on page 7
No persons under the age of 16 should be allowed to operate the equipment.
The following safety features are designed to offer a reasonable measure of
protection against injury while maintaining an operator-friendly machine. Please do not attempt
to disable or alter their functionality in any way. Any modifications will void the warranty and
pose a serious risk to the operator. Contact Drytac Technical Services as soon as any
malfunction of the equipment occurs and stop using the machine immediately!
The JM 18 and some JM 26 models use a finger guard bar for protection at the nip point. Many
JM26‟s have the electric eyes or photocells installed for safety. All JM44 and JM54 models are
equipped with an electric eye in front of the roller Nip which, when interrupted, will sound a
buzzer as a warning to indicate that an object is breaking the photocell circuit. Additionally,
when the mode switch is set to “Auto” and the buzzer sounds the rollers are stopped. (Note: Be
particularly cautious when operating the JetMounter
in the Foot Pedal mode because in this
Mode the rollers will NOT STOP when the photocells are interrupted. An audible alarm will
sound, but the rollers will continue to be powered at a reduced speed).
Prior to operating the laminator, always check that the photocell and buzzer are working
properly. Select the Auto mode and use a piece of cardboard to block the photocells to confirm
that the alarm sounds and the rollers stop.
Page 7 of 31

Text on page 8
The JM44 and JM54 JetMounters are also equipped with Red Emergency Stop buttons located
on both sides of the front or on the top on each side of the laminator. The Emergency Stop
Button will stop the machine instantly. Stopping the machine in the Foot mode can also be
accomplished by lifting your foot off the pedal, turning the speed to zero (0) OR turning off the
DO NOT operate this equipment when you are alone. As with all motorized equipment, it is
advisable that other adults be present to assist if required.
DO NOT operate the JetMounter
while under the influence of alcohol, prescription drugs or
any other substance that could impair your judgment or reaction time.
Remove any jewelry such as rings, bracelets and necklaces prior to operating the equipment.
Keep loose clothing, neckties, artificial fingernails, long hair and anything else that might easily
be drawn into the rollers away from the machine.
Power OFF if you are loading adhesives or film, cleaning the rollers or
performing other activities that require close proximity of your fingers to the Nip. This will avoid
the possibility of inadvertently starting the machine. Keep all safety guards in place and your
fingers away from the Nip area when the machine is operating.
Always work at a slow speed until you become familiar with the machine.
Exercise caution when lifting rolls of laminate and adhesive due to their weight. Use assistance
to avoid personal injury or damage to the equipment and materials.
Prior to lifting a supply shaft into the laminator, position the T-Slot in the hub on the machines‟
right side to receive the shaft. The use of an assistant is strongly recommended.
Page 8 of 31

Text on page 9
Always disconnect the laminator from the
power supply before removing any panels
When using a large supply roll, be aware that a pinch hazard can exist between
the top roller and supply shaft. When working from the rear of the laminator the
operator must be aware of the Nip point of the contacting rollers and exercise
extreme caution to avoid injury.
The sound this machine generates at the operators‟ position is less than 70dB.
Keep this manual near the machine for future reference. Also check our website
for any additional or updated safety information. (www.drytac.com)
An instructional DVD and a demonstration/training session from a Drytac representative are
also available so you can become familiar with all the features of your new JetMounter .
Contact our Customer Service Department for details or if you have any questions about the
operation of this equipment. (Contact information can be found on page 26).
Specific Moving Instructions:
The Drytac JetMounter is to be handled with care to avoid personal injury or collateral damage. Whenever the machine is moved, we strongly recommend utilizing TM at least two people. The adage: “Better safe than sorry,” applies here. The JetMounter stands are designed with fixed wheels on one side and lockable swivel casters on the other for a very good reason. When moving the machine, the movers should be positioned at both sides. Do TM not push the JetMounter from the front or back! This eliminates the possibility of having the machine tip over onto the mover or their helper.
Page 9 of 31

Text on page 10
Thank you for purchasing a Drytac JetMounter
contained in this manual will familiarize you with the basic methods of mounting and laminating
using this easy-to-use 2-roller laminator. This manual covers three JetMounter models:
25.5” (64.8 cm)
18.25” (46.4cm)
33.25” (84.5cm)
26.25” (66.7cm)
52.75” (134.0cm)
44.125” (112.1cm)
62.5” (135.3cm)
54.125” 137.5cm)
These models are similar in operation, but not identical. Unless otherwise indicated, the
instructions are for the JM26 model. Specific comments regarding the JM44 and JM54 models
will be made where differences occur.
Select a clean, well-lighted working area that allows access to both the front and back of the
machine. Position the machine on a level, sturdy surface that can support the weight of the
machine and is at an optimum working height for the operator. (See Technical Specifications
Chart on page 26 for individual weight and size dimensions). The JM 44‟s and 54‟s are available
with optional stands that have casters for ease of movement as well as a storage rack for
Upon receipt of your new JetMounter , inspect the carton(s) carefully for signs of physical
damage or mishandling. Report any damage to the shipping company immediately and Drytac
Corporation if replacement parts are needed.
If no damage is apparent proceed with the
It is recommended that two people unpack the JM 26 to avoid damage to the equipment or
personal injury. To unpack the JM 44 and 54 you must follow the instructions affixed to the top
Page 10 of 31

Text on page 11
of the crate in the sequence described. If the instructions are missing be sure to contact
Drytac Technical Services before attempting to unpack or install the machine.
Due to the weight of the JM44 and 54 laminators a hoist or suitable lift must be used to
position the machine on an appropriate table or stand.
laminators, depending on the country in which the machine was purchased, are
supplied in either a 115 VAC or 230 VAC versions. The power requirements for your particular
machine are marked on the rear panel adjacent to the power connector. Please confirm that you
have the correct power source available at the chosen location. If there are any questions about
electrical requirements for the equipment, please contact a qualified electrician prior to
attempting to power up the machine!
IMPORTED AND DISTRIBUTED BY
JETMOUNTER MODEL
SERIAL NUMBER
DATE OF MANUFACTURE
MAX. FEED RATE
WEIGHT
V ~ AC
Be absolutely certain that the voltage supplied at the outlet corresponds with the voltage marked
on the plate attached to your machine.
Do not rely on the cord or outlet configuration to
determine the correct power supply voltage!
ALLOW ENOUGH WORKSPACE AROUND THE MACHINE TO BE ABLE
TO FEED AND REMOVE YOUR WORKPIECE SAFELY! It is recommended that the machine be placed so that at least three feet of space from the front and back beyond the largest piece of material you will use be provided to insure adequate accessibility and safety. For example, if your work piece were a four-foot by eight-foot foam board, you would need to allow a minimum
Page 11 of 31

Text on page 12
of eleven feet of space in front and eleven feet of space in the rear of your machine. Always consider this rule a necessity prior to beginning your work.
- The main On-Off switch (rocker switch located on the back of the machine). This switch
should be in the “OFF” position when loading or unloading adhesives or film, cleaning the
rollers or performing other activities that require close proximity of your fingers to the Nip.
- The Auto/Foot/Reset switch.
This two-position switch is used to choose the mode of
operation between “Foot” and “Auto”. The photocell safety feature functions differently in
each position, review the safety information prior to selecting the mode of operation. Once
the photocell is tripped or the Emergency Stop has been activated, you must first remove
the obstruction or correct the cause for the shut down. To reset the machine you must reset
the circuit breaker on the back of the machine and then toggle the Auto/Foot/Reset switch
from the position it was in when the interruption occurred.
- The Foot Pedal switch should be located on the floor within easy reach of the operator and
is used to activate the roller when the Auto/Foot switch is in the “Foot” mode.
- The Forward/Reverse switch (on front control panel) is used to select the direction of the
Upon start up, place the switch in the “OFF” position. Reverse only
operates in Foot mode.
Page 12 of 31

Text on page 13
- The Speed Control knob. Rotating the knob to the right will increase the speed of the roller
in either “Foot” or “Auto” mode. Upon start up, rotate the knob all the way to the left to the
- The Pressure Control Knobs are located on the top of each side. They adjust the top roller
height and pressure. Rotate both Pressure Control Knobs counter-clockwise to raise the
top roller. (See “Setting Roller Pressure” to adjust the pressure properly).
- The Supply Shaft holds the adhesive or laminate material, while the Take Up or wind-up
shaft holds the release liner.
When either of the shafts is installed, the T-slot end must be oriented
properly to fit in the drive mechanism located on the right end of the machine, (as you face it
from the front). The operator and the assistant should consider this prior to lifting the loaded
Once in position, be alert to the possible pinch hazard at the left or un-driven end.
Page 13 of 31

Text on page 14
This procedure begins with the main power switch off, the mode switch set to Auto, the
directional switch set to the OFF position, the speed knob to the far left or zero. The following
steps apply to setting the roller pressure ONLY.
- Rotate both Pressure Control Knobs counter-clockwise to raise the top roller.
- Slide a section of the mounting board into the roller Nip.
- Rotate both Pressure Control Knobs clockwise to lower the top roller until it makes light
contact with the mounting board.
- Turn the main switch to the ON position; the power indicator light will come on.
- Turn the mode switch to the Foot position.
- Turn the Forward/Reverse switch to the Reverse position.
- Depress the Foot Pedal*.
- Slowly turn the Speed Control knob to remove the board from the rollers (reverse).
- Switch the Forward/Reverse switch to the OFF position.
Page 14 of 31

Text on page 15
- For optimal results, rotate both Pressure Control knobs approximately 1/8 of a turn
clockwise to slightly lower the roller (after the board has been removed).
NOTE: The Foot Pedal acts as a safety device. When the mode switch is set to the
Foot position, the laminator will not operate unless the Foot Pedal is depressed. For
continuous operation set the mode switch on the control panel to Auto.
Adjusting Shaft Tensions on JM44 and JM54 Models:
JM44 and JM54 models are equipped with a motorized Take Up Shaft on the
front of the machine. This shaft winds up the release liner from mounting adhesive and over
laminating film rolls during processing. Also on these models, both the Take Up shaft and the
Supply shaft are equipped with Tension Control Knobs. By adjusting these knobs you control
the speed of the shafts as they unwind or wind up material.
It is important to adjust these settings so that there is an even tension on the adhesive or film
during processing. The objective is to apply enough resistance on the film to keep it firm and
flat, but not so much as to stretch or distort it. It is also critical to maintain even tension
settings on both sides of the film.
Turn the Tension Control Knobs clockwise to increase roll tension and counter-clockwise to
Page 15 of 31

Text on page 16
Supply shaft tension: When feeding adhesive or film into the rollers, the primary objective is to
maintain the feed at the same rate as the rollers pull the material through the Nip.
Take Up shaft tension: The Release Liner should be pulled away from the adhesive at a
steady rate that allows it to “lift” at a point just before the material enters the Nip.
Mounting Board (Substrate) Selection:
The selection of a proper mounting board/substrate is very important. Common materials used
are:
- Foam Boards: (FomeCor®, GatorBoard®, HartBoard® etc.)
- MDF (medium density fiberboard)
- Corrugated plastic boards: CoroPlast®
- Rigid Plastic Boards (Sintra®, styrene, etc.)
- Tempered hardboard: Masonite®
Once the mounting board has been selected, determine whether to pre-coat the material with
adhesive or to purchase pre-cut and pre-coated boards. While the use of pre-cut, pre-coated
materials will save time, coating your own mounting board is more economical and allows for
maximum flexibility in terms of sizing and substrate selection.
Pre-coating the Mounting Board
Pre-coating a mounting board means applying a mounting adhesive to one side of the board so
that a graphic image can be mounted to the board later). The use of a Leader Board is
recommended for this process.
- Adjust rollers for proper pressure (see page 13).
Page 16 of 31

Text on page 17
- Load the roll of PSA (pressure-sensitive adhesive) onto the Supply shaft so that the material
can be pulled toward the user from the underside of the roll with the adhesive side facing UP
(the release liner side should be in contact with the roller as shown in the Illustration).
- Pull the adhesive off of the roll so that about 4” lies flat on the worktable and is draped in
front of the rollers.
- Lay your Leader Board on top of the exposed adhesive material on the worktable; then push
the Leader Board and adhesive into the Nip (the „Nip‟ of your laminator is the point where
the rollers make contact). When pushing the Leader Board into the adhesive, make sure it is
parallel to the rollers.
- Position your first mounting board behind and against the Leader Board. Check for proper
alignment, and feed through the rollers (in either AUTO mode or via FOOT switch). Feed
one board after another as needed.
Trim the excess adhesive off of the board.
- Your mounting boards are now pre-coated with pressure-sensitive adhesive, which is still
protected by the release paper. The pre-coated boards can be used for immediate mounting
or stored for future use.
Page 17 of 31

Text on page 18
TIP: When an image is going to be laminated with a gloss overlaminating film, the use of very
smooth substrates with glossy surfaces (such as Masonite®) is preferred. This will minimize the
effect of board imperfections, (i.e. “orange peel”) in the finished product.
For models JM44 and MJ54, adjust the Supply shaft tension properly (page 14).
NOTE: We recommend placing a „Tail Board‟ behind the last production board (this can be the
same board used as a leader board/starting panel). This is especially important when pre-
Mounting a Graphic to a Pre-Coated Board
- Adjust the rollers for proper pressure (see Page 13).
- Expose the adhesive on the board by folding back approximately 1” (2.5cm) of the release
- Using the folded-back release paper as a temporary support bridge, align the print onto the
board and then proceed to “tack”(which means to stick or press down) the leading edge of
the print onto the exposed adhesive.
- Run a Leader Board of the same thickness as your mounting board through the rollers so
that the back edge of the Leader Board is at the nip of your machine.
Page 18 of 31

Text on page 19
- Square your mounting board with the tacked print against the edge of the
and drape the print over the top roller.
- Run the mounting board/adhesive/image through the rollers while simultaneously pulling the
release liner away from and off of the board.
(JM44 and JM54 models have automatic Take Up shafts on the front of the chassis. You may
choose to unwind the Release Liner onto the Take Up shaft during this process, rather than
pulling it by hand. See page 14 for information on setting the Take Up Shaft tension).
Laminating with JetMounter Series Laminators
Selecting a Laminating Film
Select an appropriate overlaminating film for the surface of your image based on aesthetics and
the conditions under which it will be displayed. Drytac offers a wide variety of films to match
your specific output and application. Please consult your Drytac catalog for descriptions of
There are several types of laminating jobs that can be performed on JetMounter laminators. The
following are the most common applications. To prevent adhesives from sticking to the rollers
and to provide a reusable, standard working surface, the use of a silicone-coated board (also
Page 19 of 31

Text on page 20
known as a “Carrier Board”) is highly recommended. (See page 22 for instructions).
Laminating a Single Unmounted Image
Before processing, make sure that the image is clean and free of dust or specks of lint (an Anti-
Static cloth or Anti-Static Wisk is recommended for this purpose).
- Raise the top roller and insert the Carrier Board. Set roller pressure as shown on page 10.
- Pre-cut a sheet of overlaminating film from the roll. (The sheet should be larger than the
image by approximately 1” on each side and bottom, and 2” on the top).
- Peel and fold back approximately 2” of release liner from the top edge of the overlaminating
film. Tack the film on the Carrier Board by pressing the exposed section of film onto the
leading edge of the board.
- Start the Carrier Board into your laminator using the Foot Pedal mode. Stop before the edge
of the laminating film reaches the rollers.
- Lift up the remainder of the overlaminating film (which is still protected by the release liner)
Page 20 of 31

Text on page 21
and slide the image face up underneath it. Stop before it makes contact with the exposed
part of the adhesive. It is important to keep the film adhesive away from the artwork until the
whole assembly is under pressure and traveling through the JetMounter TM .
- Lay the laminating film over the top of the upper roller. While holding up the edge of the
peeled back release liner with one hand, start the rollers and apply the overlaminating film to
the surface of the image. Pull up and away on the release paper as your work piece travels
through the laminator. Ensure that the release paper does not reach the point where the
image makes contact with the top roller. Be sure to complete this step with a consistent
motion and do not stop until the entire image has passed through the rollers.
- The laminated image can now be easily removed from the silicone-coated Carrier Board for
Laminating a Single Mounted Image
Before processing, make sure that the images are clean and free of dust or specks of lint (an
Anti-Static cloth or Anti-Static Wisk is recommended for this purpose).
- Raise the top roller and insert the mounted image into the roller Nip. Adjust the roller
pressure as described on page 13.
- Pre-cut a sheet of overlaminating film from the roll. The sheet should be larger than the
image by approximately 1/4” on the sides and bottom and 3” longer on the top.
- Peel and fold back 2” of release paper liner exposing the adhesive of the laminating film.
- Tack approximately 1-1/2” of the laminating film to the Leader Board, but not over the
- Insert the Leader Board with the laminating film tacked to it into the Nip. Advance the Leader
Board and the film through the Nip until the upper laminating roller securely pinches the film.
(The trailing edge of the Leader Board should be at the pinch point of the rollers.)
- Lay the laminating film over the top of the upper laminating roller. Make sure that the folded
release paper liner is easily accessible.
Page 21 of 31

Text on page 22
- Slide the mounted image into the Nip area and allow its edge to make contact with the edge
of the Leader Board.
- While holding up the folded edge of the peeled back release paper with one hand, start the
rollers and apply the laminating film to the surface of the image. Pull up and away on the
release liner as you advance to ensure that the liner does not reach the Nip area. Process
your work with a consistent motion and do not stop until the entire image has passed
- Trim excess overlaminating film from the edges of the image.
Laminating Multiple Mounted Images
- For higher volume jobs, select a roll of laminating film slightly wider than the mounted
images you intend to laminate.
- Install the overlaminating film on the Supply shaft so that the material can be pulled toward
the user from the bottom of the roll with the Release Liner side facing up.
- Adjust the rollers for proper pressure (see page 13).
Page 22 of 31

Text on page 23
- Pull several inches of the overlaminating film off the roll. Separate the overlaminating film
from its release liner (approximately 3-4”) and drape it onto the in-feed table in front of the
rollers. Keep the release liner away from the film while pushing the Leader Board and film
into the roller Nip.
- Position the first mounted image to be laminated against the back of the Leader Board.
Check for proper alignment, and feed through the rollers of your laminator (in Auto mode or
with foot pedal). Feed one print in right after another, as needed.
- Carefully separate prints with a razor blade or utility knife. Trim off the excess film.
JM44 and JM54 models have automatic Take Up shafts on the front of the chassis. You may
choose to unwind the Release Liner onto the Take Up shaft during this process, rather than
pulling it by hand. (See page 14 for information on setting Take Up Shaft tension).
Using a Leader Board
A Leader Board (also referred to as a “starting panel”) is recommended for use when mounting
and laminating with JetMounter
laminators. A Leader Board is fed into the roller Nip first,
followed by the actual mounting/laminating project to be processed. We highly recommend this
Page 23 of 31

Text on page 24
tool to help set proper pressure for both mounting and laminating prior to processing your work.
The Leader Board should be the same width and thickness of your production mounting board
and about 6-8” long. You should also make a Tail Board, which is used behind the last
production board. The Tail Board is especially recommended for mounting to foam board.
When processing un-mounted images, we recommend you use a silicone-coated board to
prevent adhesives from sticking to the rollers. This board is called a Carrier Board, and it
provides a re-usable, standard working surface. It will be used when laminating your image prior
to mounting it onto a mounting board/substrate. It is common practice for finishing professionals
to stock Carrier Boards in several different sizes to accommodate various artwork formats.
Making a Carrier Board is basically the same process as pre-coating a mounting board.
Instructions for this process are found on page 15. When the mount board is coated with the
adhesive, the silicone-coated release liner provides a slick, non-stick surface on which to
Be sure to use a “self-wound” adhesive with a silicone treated liner for this purpose.
2: Preparing Mounting Boards
Once you have decided on the most appropriate adhesive/mounting board combination for your
application, it is important that you properly prepare your board before coating. Although often
overlooked, this can be the most important step when mounting a print or artwork for display.
(E.G. FOME-COR®, ETC.)
The surface of these types of substrates is porous and often contains particles that can spoil an
otherwise perfect mount. Clay-coated surfaces such as Fome-Cor®, Foam-X® and similar
boards should simply be wiped with a TacCloth™ to remove dust particles.
Page 24 of 31

Text on page 25
To prepare mat board or millboard for mounting, use the Anti-Static Wisk™ brush to remove
dust particles and other debris.
(E.G. MEDIUM DENSITY FIBERBOARD, MASONITE, ETC.)
To prepare hardboard substrates for mounting, wipe down the surface with a TacCloth. If the
surface contains irregularities, use sandpaper to remove them, and then wipe the surface with a
Please note: Due to their highly absorbent properties, do not wipe down the surfaces of any of
these substrates (i.e. foam board, mat/millboard or hardboard) with a moist rag.
Using a TacCloth to wipe down foam board.
Tip: It is important that you remove dust and other debris from your prints prior to mounting.
Page 25 of 31

Text on page 26
CAUTION: Unplug the machine before performing any service or maintenance.
Cleaning: In order for your JetMounter
to operate efficiently, be sure to clean it
regularly with a soft cloth. A neutral mixture of soap and water can be used for this
purpose. To remove heavy dirt and adhesive residue we suggest the use of 99%
Do not use thinner or a metal brush to clean the rollers.
Rollers: In order to extend the life of your JetMounter laminator it is strongly
recommended that the rollers be separated when the machine is not in use.
Fuses: There are two replaceable fuses on your JetMounter located on the rear panel
where the power cord enters the machine.
One is actually in the power cord
receptacle. The other is in a separate holder next to the power cord. Fuses are
5x20mm 1, 2 & 8 A depending on the particular machines‟ voltage requirements. The
use of any other fuse may endanger the operator and/or machine and invalidate the
Lubrication: Lubricate the drive chain located behind the right hand end cover every six
months, with a premium brand chain lubricant. Disconnect power before lubricating
the chain. No other parts require lubrication.
Before contacting Drytac for service assistance, please double-check to make sure that the
is still connected to a live power outlet. Next, check both fuses. For further
troubleshooting assistance, please contact Drytac Technical Services. See Contact Information
on the page 28.
Page 26 of 31

Text on page 27
Roller Construction
Steel-with high-release silicone covering.
51 lbs / 23kg
Maximum Opening Max. Material Diameter Power Requirements
2.5 – 18 fpm
3 – 10 fpm
Power Consumption Fuse Specifications
115 VAC or 230 VAC* 50/60 Hz
One 1A or 2A fuse in power receptacle*. One 8A in adjacent holder. Both are 5x20mm Fast-Acting glass fuses.
PACKAGED FOR SHIPMENT
- Fuse rating for Europe is 1A, and for North America use a 2A..
Stands are approximately 29.71” (755mm) tall, making the overall
height of the assembled unit 48.71” (1237 mm).
On a JM44/54 attached to a stand, the
distance from the floor to the feed table is approximately 34.58” (878.33 mm).
Page 27 of 31

Text on page 28
CONTACT INFORMATION
5383 Glen Alden Drive
Bristol BS16 3RY, United Kingdom
Toll Free Phone: 800-280-6013
Phone: +44 (0) 117-958-6500
Toll Free Fax: 800-622-8839
Toll Free Phone: 0845-070-0660 (UK only)
Toll Free Phone: 800-353-2883
Toll Free Fax: 877-437-9822
C OMPANY N AME :
A DDRESS :
C ITY / S TATE :
M ODEL #:
S ERIAL #:
P URCHASE D ATE :
W ARRANTY C ARD R ETURNED ON :
BY:
Page 28 of 31

Text on page 29
WARRANTY
We thank you for your purchase of the JetMounter
laminator and want to assure you that we
will do our best to see that your experience with your new machine is a positive one. Every
Drytac machine is designed and manufactured to give many years of dependable service.
To achieve the best results from your JetMounter , the machine should be set up and operated
in accordance with the instructions included in this manual.
Should the original JetMounter
purchaser experience any problem due to faulty materials or
workmanship within 12 months of the purchase date, Drytac or their dealer will arrange for the
machine to be repaired, replaced or refunded at Drytac‟s discretion.
After the warranty period has elapsed, Drytac will provide all reasonable assistance and product
support to resolve any problems that may arise.
Please return your warranty card as soon as possible. This will help us more efficiently assist
with any problem you may encounter.
You will find a section for recording this important
information for your records and any future parts or service requests on page 27 of this manual.
Normal wear and tear, any damage to the silicon rollers, damage due to abuse, improper
operation or installation is not covered by this warranty.
Conditions that will void the warranty
include-but are not limited to; failure to follow the instructions contained in this manual,
unauthorized changes or modifications to the machine or the stand (where applicable) in any
manner, misuse of the machine for purposes other than specified in the Operators Manual.
Drytac will not be responsible for any damage or consequential damage caused by the
Please feel free to contact Drytac if you have any questions or problems.
Before calling Drytac Technical Services, complete the JetMounter Registration Information on
the previous page and have it available for reference.
Page 29 of 31

Text on page 30
Replacement Parts for the JetMounter Series Laminators
Parts Applicable to Most Models
Pressure/Tension Knob Speed Control Switch with Knob Motor Switch, Fwd./Rev Mode/Reset Switch On/Off Switch
JMS-01 JMS-03 JMS-04 JMS-05 JMS-09 JMS-10, JMS-10E for European JMS-10UK for UK application
Part Number JMS UK fo
JM 18 Silicon Roller JM 18 Roll Shaft Core Adapter for JM 18/26 Foot Control for JM 18/26 JM 26 Silicon Roller JM 26 Roll Shaft
JMS1-01 JMS1-02 JMS12-03 JMS12-04 JMS2-01 JMS2-02
Silicon Roller Supply Shaft
JMS4-01 JMS4-03
Silicon Roller Supply Shaft
JMS5-01 JMS5-03
1A Fuse- European Models 2A Fuse-All Other Models 8A Fuse- All Models Pressure Adjustment Handle Circuit Breaker
JMS45-04 JMS45-02 JMS45-03 JMS45-13 JMS45-15
The list above does not include all service parts available. For further parts or service information please contact Drytac Technical Services (see page 28 for Contact Information).
Page 30 of 31

Text on page 31
B Revision Functional Requirements
ACTION
PROGRAMMED SOFTWARE FUNCTIONS
AUTO MODE
LED
Normal operation at set speed Machine stops
Press and Hold Rev. Button
Power Up or E-Stops Reset=Needs Reset
FOOT MODE
FOOT pedal pressed, FWD mode
Photocell interrupted. FP still depressed
Photocell cleared. FP still depressed.
Photocell cleared. FP dep. Switch to Auto
Restart by FP, no buttons pressed
Press and hold REV in Foot Mode,
Release REV button while depress FP
Table Down, FOOT pedal released. (JM63 only)
Machine Stops, Ready to start Will not Run
Table Down, FOOT pedal pressed. (JM63 only)
In Rev. with Foot on pedal- press AUTO
Page 31 of 31 ยท End of manual
Quick start
- Place the machine: set it on a level, sturdy surface with access to the front and back. Leave at least three feet of space in front and behind beyond the largest piece you will run.
- Check the power: make sure the outlet voltage matches the voltage on the plate on the rear panel (115 VAC or 230 VAC). Do not judge it by the cord or outlet shape.
- Start safe: with the main rocker switch on the back off, set the mode switch to Auto, the Forward/Reverse switch to OFF, and the speed knob all the way left to zero.
- Set roller pressure: raise the top roller, slide a piece of your mounting board into the Nip, and lower the roller until it lightly touches the board. Back the board out in Foot mode and reverse, then turn both pressure knobs about 1/8 of a turn clockwise.
- Load material: with the power OFF, load the roll onto the Supply shaft with the T-slot end on the right, so the material pulls toward you from the underside with the adhesive side facing UP.
- Run: feed a Leader Board the same width and thickness as your board and about 6 to 8" long into the Nip first, then feed your boards in Auto mode or with the foot pedal. Work at a slow speed until you know the machine.
- Finish: trim the excess adhesive or film from the board. When you are done, separate the rollers to extend their life.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not run at all | No power or a blown fuse | Check that the machine is connected to a live power outlet, then check both fuses on the rear panel where the power cord enters. Page 26 |
| Rollers do not turn in Foot mode | The foot pedal is a safety device and must be held down | Depress the foot pedal, or set the mode switch to Auto for continuous operation. Page 15 |
| Reverse does not work | Reverse only operates in Foot mode | Set the mode switch to Foot, select Reverse and depress the foot pedal. Page 12 |
| Machine will not restart after a safety stop | The safety circuit needs to be reset | Remove the obstruction or cause of the stop, reset the circuit breaker on the back, then toggle the Auto/Foot/Reset switch from the position it was in. Page 12 |
| Adhesive sticks to the rollers when laminating an unmounted image | No Carrier Board used | Run unmounted images on a silicone-coated Carrier Board, made with a self-wound adhesive with a silicone treated liner. Page 24 |
| Release liner gets drawn into the Nip | Liner not pulled away as the work advances | Hold the folded edge of the liner and pull it up and away as the work advances, with a consistent motion and no stopping. Page 22 |
| "Orange peel" shows in a gloss laminated piece | Board surface imperfections show through the gloss film | Use very smooth substrates with glossy surfaces when laminating with gloss overlaminating film. Page 18 |
| Particles or bumps under the mounted print | Dust or debris on the board or the print | Wipe foam board and hardboard with a TacCloth, brush mat board with an anti-static brush, and clean the print first. Do not wipe these boards with a moist rag. Page 25 |
Frequently asked questions
What boards can I mount onto?
Common mounting boards are foam boards, MDF (medium density fiberboard), corrugated plastic boards, rigid plastic boards and tempered hardboard. You can pre-coat your own boards with adhesive or buy pre-cut, pre-coated boards. See page 16.
What safety features does the JM18 have?
The JM 18 uses a finger guard bar for protection at the nip point. In Foot mode, the laminator will not run unless the foot pedal is depressed. No one under the age of 16 should operate it. See page 7, page 15.
What fuses does it use?
Two 5x20mm Fast-Acting glass fuses: one 1A or 2A fuse in the power receptacle (1A for Europe, 2A for North America) and one 8A fuse in the holder next to it. The part numbers are JMS45-04 (1A), JMS45-02 (2A) and JMS45-03 (8A). See page 27, page 30.
What maintenance does it need?
Unplug it first. Clean it regularly with a soft cloth and a neutral mix of soap and water, and never use thinner or a metal brush on the rollers. Lubricate the drive chain behind the right hand end cover every six months with a chain lubricant. No other parts need lubrication. See page 26.
What are the JM18 replacement part numbers?
JM 18 Silicon Roller is JMS1-01, JM 18 Roll Shaft is JMS1-02, Core Adapter for JM 18/26 is JMS12-03, and Foot Control for JM 18/26 is JMS12-04. See page 30.
How big should I cut the film for an unmounted image?
Cut the overlaminating film about 1" larger than the image on each side and the bottom, and 2" larger on the top. Run it on a Carrier Board. See page 20.
