

Page 1 of 5

Text on page 2
MAX & SIMPLEX
Inspired Design – Precision Engineering
USER INSTRUCTIONS
KC-EDITION 6977-11/10
Thank you for choosing the Keencut MAX/SIMPLEX. Every effort has been made to bring you a precision engineered product with the promise of many years of valuable service. In order to obtain maximum benefit from your machine please read these instructions carefully. For advice and assistance or replacement parts please contact your distributor or Keencut.
Page 2 of 5

Text on page 3
SAFETY
Setting Up
Only lift or move the MAX/SIMPLEX using the grip on the top edge of the cutter bar. If there is a need to handle the cutter in any other way or to move it away from its cutting bench, the blade must be removed first.
WARNING
It is essential that the MAX/SIMPLEX is used on a flat surface to cut accurately. A warped or bowed table top can induce a twist in the MAX/SIMPLEX resulting in a bowed cut.
Inserting and setting the blade
The blade is inserted from the back of the blade holder, push it fully forward and tighten the wingbolt.
To set the blade for a repeatable cutting depth unclamp the blade and turn the knob at the front of the cutter, clockwise to increase blade depth & counter clockwise to decrease.
Page 3 of 5

Text on page 4
Using the MAX/SIMPLEX . . .
. . . for cutting film and lightweight materials.
Position the material under the MAX/SIMPLEX and align the sight edge with cut line of the material. The MAX/SIMPLEX will cut within 0.5 to 1mm [0.02” to 0.04”] of the sight edge, this small gap allows easier alignment when cutting to the edge of an image. Place your hand on the cutter, as shown, with your finger tips positioned on the front edge of the cutter. Depress the cutter and pull to cut, there is no need to hold the MAX/SIMPLEX down when cutting lightweight materials.
. . . for cutting PVC foamboard and heavyweight materials.
Position the material under the MAX/SIMPLEX and align the sight edge with your cutting marks. The MAX/SIMPLEX will cut within 0.5 to 1mm [0.02” to 0.04”] of the sight edge, this small gap allows easier alignment when cutting to the edge of an image. Place your hand on the cutter, as shown. Place your left hand on the finger grip of the straight edge, depress the cutter and push it away from you to cut. Dependent upon the nature and thickness of the material you may need to take more than one cut gradually increasing the depth.
Page 4 of 5

Text on page 5
Maintenance
Do not use oil or spirits to lubricate or clean the MAX/SIMPLEX, some of the plastic components and bearings may be damaged.
It is good practice to keep a dust sheet over the MAX/SIMPLEX if it is not to be used for extended periods. In any event regularly clean it with a dry cloth, to remove any stubborn stains use a cloth dampened with a little water/detergent.
Should the cutting head slideway require lubrication use a silicon spray or impregnated sponge.
The bearings that control the sliding motion of the cutting head are manufactured from a high grade polymer and under normal use will last for an extremely long time. As they settle into position you may find a slight amount of side play, this can be removed by tightening the two adjustment screws.
Should you require any advice or technical information please contact your distributor or Keencut direct.
KEENCUT Limited accepts no liability if the product is not assembled and used in the correct way.
Page 5 of 5 · End of manual
Quick start
- Seat the blade: Slide a blade into the holder of the SIM210 from behind, push it all the way forward and snug up the wingbolt (page 3).
- Dial the depth: Loosen the blade clamp and twist the front knob. Turning right cuts deeper and turning left cuts shallower, and the setting repeats from cut to cut (page 3).
- Check the bench: Put the cutter on a flat table, since a bowed top twists the machine and bows the cut. Carry it only by the top grip, and take the blade out before any other handling (page 3).
- Light films and sheets: Slip the material beneath, match the sight edge to the cut line, rest fingertips on the front edge, press down and pull. No extra downward hold is needed (page 4).
- Foamboard and heavy stock: Set your left hand on the straight edge finger grip, press the cutter down and push it away from you. Thick material may need several passes, each a little deeper (page 4).
- Keep it clean: Wipe with a dry cloth, or a damp one with a little detergent for stains. Skip oil and spirits. Cover it when idle, and use silicon spray on the slideway if needed (page 5).
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| SIM210 gives a bowed cut | A warped or bowed table top can twist the MAX/SIMPLEX. | Use the cutter on a flat surface. Page 3 |
| Blade depth is not repeatable | The blade depth has not been set with the front knob. | Unclamp the blade, then turn the knob at the front of the cutter. Clockwise increases depth and counter clockwise decreases it. Page 3 |
| Blade is loose in the holder | The blade was not pushed fully forward or the wingbolt is not tight. | Insert the blade from the back of the holder, push it fully forward and tighten the wingbolt. Page 3 |
| Heavyweight material is not cut through | PVC foamboard and heavy materials can need more than one cut. | Take more than one cut and increase the depth gradually. Push the cutter away from you while holding the straight edge finger grip. Page 4 |
| Cutter needs to be moved | Moving it by other parts risks the blade. | Lift only by the grip on the top edge of the cutter bar. If you must handle it another way, remove the blade first. Page 3 |
| Side play in the cutting head | The bearings settle in with use. | Tighten the two adjustment screws. Clean with a dry cloth, and do not use oil or spirits. Page 5 |
Frequently asked questions
Can I oil the Keencut SIM210 slideway?
Do not use oil or spirits on it, as plastic parts and bearings may be damaged. If the slideway needs lubricant, use a silicon spray or an impregnated sponge. See page 5.
How close to the sight edge does it cut?
The cutter cuts within 0.5 to 1mm (0.02 to 0.04 inch) of the sight edge, which makes it easier to cut to the edge of an image. See page 4.
How do I change the blade depth?
Unclamp the blade and turn the knob at the front of the cutter. Turn it clockwise to increase depth. See page 3.
Why is my cut bowed?
A warped or bowed table top can twist the cutter. Use it on a flat surface. See page 3.
How do I remove side play in the cutting head?
As the polymer bearings settle in you may feel slight side play. Tighten the two adjustment screws to remove it. See page 5.
