

Page 1 of 4

Text on page 2
LasscoJog LJ-2 Paper Jogger
Serial Number: Date of Purchase: Dealer: Address:
Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference.
Telephone Number:
485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com info@lasscowizer.com
Page 2 of 4

Text on page 3
Instructions
Setting Up Your Machine
Your LJ-2 LasscoJog Paper Jogger comes ready to use. Simply plug in the power cord and turn on the machine.
Adjusting the Jogging Speed
To change the Jogging action, access the adjustment discs on the underside of the machine as shown. Loosen Button Head Machine Screw and rotate one of the Adjustment Discs attached to the Disc Shaft extending from the Motor . Tighten down the Machine Screw.
L-1020: #6 Hose Clamp
L-1017: Eccentric Adjustment Disc
10-32 Screw x 3/4 Button Head Machine Screw
L-1018: Eccentric Disc Shaft
3/8” ID x 3/4” OD Fiber Washer
Note:
When the screws are located opposite each other on the shaft, the minimum action is obtained. When the screws are located on the same side of the shaft, the maximum action is obtained. Normal action is obtained when the screws are 80 to 90 apart.
Page 3 of 4

Text on page 4
Trouble Shooting Guide
Problem
Cause
Correction
Machine does not turn on.
Machine is not plugged in or there is no electricity to the outlet.
Make sure the power cord is connected correctly and that the outlet is live.
Power switch is faulty.
Contact a service technician to replace the power switch.
Motor has burned out.
Contact a service technician to replace the motor.
The Torque Tube (L-1019) has worn out or broken.
Replace the Torque Tube.
The screw on the Eccentric Adjustment Disc (L-1017) has come loose allowing the disc to shift.
Access the Adjustment Discs and tighten down the screw as shown on page 1.
The motor turns on but the machine does not jog as desired.
Page 4 of 4 · End of manual
Quick start
- Plug in: The LJ-2 comes ready to use. Plug in the power cord.
- Turn on: Turn on the machine.
- Reach the adjustment discs: To change the jogging action, access the adjustment discs on the underside of the machine.
- Loosen and rotate: Loosen the button head machine screw. Rotate one of the adjustment discs on the disc shaft that extends from the motor.
- Pick the action level: Screws on opposite sides of the shaft give minimum action. Screws on the same side give maximum action. Normal action is when the screws are 80 to 90 apart.
- Tighten: Tighten down the machine screw.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not turn on. | The machine is not plugged in, or there is no electricity to the outlet. | Make sure the power cord is connected correctly and that the outlet is live. Page 4 |
| Machine does not turn on. | The power switch is faulty. | Contact a service technician to replace the power switch. Page 4 |
| Machine does not turn on. | The motor has burned out. | Contact a service technician to replace the motor. Page 4 |
| The motor turns on but the machine does not jog as desired. | The Torque Tube (L-1019) has worn out or broken. | Replace the Torque Tube. Page 4 |
| The motor turns on but the machine does not jog as desired. | The screw on the Eccentric Adjustment Disc (L-1017) has come loose, allowing the disc to shift. | Access the adjustment discs and tighten down the screw. Page 4 |
Frequently asked questions
How do I set up the LasscoJog LJ-2?
It comes ready to use. Plug in the power cord and turn on the machine. See page 3.
How do I change the jogging action?
Access the adjustment discs on the underside. Loosen the button head machine screw, rotate one of the discs, and tighten the screw. See page 3.
What disc position gives normal jogging action?
Normal action is obtained when the screws are 80 to 90 apart. Opposite sides give minimum action and the same side gives maximum action. See page 3.
Why won't my paper jogger turn on?
Check that it is plugged in and that the outlet is live. If it still fails, the power switch or motor may need replacing by a service technician. See page 4.
The motor runs but the jogger does not jog right. What should I check?
The Torque Tube may be worn or broken, or the screw on an eccentric adjustment disc may be loose. Replace the tube or tighten the screw. See page 4.
