Lassco Wizer LasscoJog LJ-4 Table Top Paper Jogger Operator Manual, page 1

Page 1 of 5

Lassco Wizer LasscoJog LJ-4 Table Top Paper Jogger Operator Manual, page 2
Text on page 2

LasscoJog LJ-4 Paper Jogger

Serial Number: Date of Purchase: Dealer: Address:

Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference.

Telephone Number:

485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com info@lasscowizer.com

Page 2 of 5

Lassco Wizer LasscoJog LJ-4 Table Top Paper Jogger Operator Manual, page 3
Text on page 3

Instructions

Please remove and inspect the following items.

L-260A: Table Assembly (1)

8-32 x 1 Flat Head Screws (4)

#8 Lock Washers (4)

8-32 Stop Nut (8)

Setting Up Your Machine

Attach the Table (L-260A) to the Table Support using four (4) 8-32 x 1 Flat Head Screws, eight (8) 8-32 Stop Nuts, and four (4) #8 Lock Washers.

Step #1 Insert the four (4) Flat Head Screws through the front of the Table as shown.

Step #2 Place the Flat Head Screws through the holes of the Table Support.

Step #3 Attach the first Stop Nut and tighten.

Step #4 Place a Lock Washer over the screw.

Step #5 Attach the second Stop Nut and tighten.

Step #6 Repeat steps 3 - 5 on the remaining screws.

Page 3 of 5

Lassco Wizer LasscoJog LJ-4 Table Top Paper Jogger Operator Manual, page 4
Text on page 4

Instructions

Adjusting the Jogging Speed

To change the Jogging action:

Step #1 Open the back panel on the rear of the machine by removing the two bottom screws and flipping the cover up as shown in the rear view.

Step #2 Loosen the Button Head Machine Screw and rotate one of the Adjustment Discs attached to the Disc Shaft extending from the motor .

Step #3 Tighten down the Machine Screw.

L-1020: #6 Hose Clamp

L-1017: Eccentric Adjustment Disc

10-32 Screw x 3/4 Button Head Machine Screw

L-1018: Eccentric Disc Shaft

3/8” ID x 3/4” OD Fiber Washer

Note:

When the screws are located opposite each other on the shaft, the minimum action is obtained. When the screws are located on the same side of the shaft, the maximum action is obtained. Normal action is obtained when the screws are 80 to 90 apart.

Page 4 of 5

Lassco Wizer LasscoJog LJ-4 Table Top Paper Jogger Operator Manual, page 5
Text on page 5

Trouble Shooting Guide

Problem

Cause

Correction

Machine does not turn on.

Machine is not plugged in or there is no electricity to the outlet.

Make sure the power cord is connected correctly and that the outlet is live.

Power switch is faulty.

Contact a service technician to replace the power switch.

Motor has burned out.

Contact a service technician to replace the motor.

The Torque Tube (L-1019) has worn out or broken.

Replace the Torque Tube.

The screw on the Eccentric Adjustment Disc (L-1017) has come loose allowing the disc to shift.

Access the Adjustment Discs and tighten down the screw as shown on page 1.

The motor turns on but the machine does not jog as desired.

Page 5 of 5 · End of manual

Quick start

  1. Record your details: write the serial number, date of purchase and dealer on page 2, and keep the instructions for future reference.
  2. Unpack and check: inspect the table assembly (L-260A), four 8-32 x 1 flat head screws, four #8 lock washers and eight 8-32 stop nuts.
  3. Seat the screws: push the four flat head screws through the front of the table, then through the holes of the table support.
  4. Fasten the table: on each screw, tighten the first stop nut, slip on a lock washer, then tighten the second stop nut.
  5. Open the back panel: remove the two bottom screws on the rear of the machine and flip the cover up to reach the adjustment discs.
  6. Set the jogging action: loosen the button head machine screw and rotate an adjustment disc on the disc shaft. Opposite sides give minimum action, the same side gives maximum action and 80 to 90 apart gives normal action.
  7. Lock the setting: tighten the machine screw. For help, contact Lassco Wizer at 585-436-1934.

Troubleshooting

ProblemLikely causeFix (from the manual)
The jogging action is too weakThe adjustment disc screws are set for less actionOpen the back panel and rotate a disc so the screws sit on the same side of the shaft for maximum action. Tighten the machine screw. Page 4
The jogging action is too strongThe disc screws are set for maximum actionRotate a disc so the screws are opposite each other for minimum action, or 80 to 90 apart for normal action. Page 4
The table is not firmly attachedThe nuts on the flat head screws are not all tightenedCheck each screw has a tightened first stop nut, a lock washer and a tightened second stop nut. Page 3
You cannot reach the adjustment discsThe back panel is closedRemove the two bottom screws on the rear of the machine and flip the cover up. Page 4
You need a replacement part for the jogging mechanismA disc, shaft or fastener is worn or lostOrder L-1017 (Eccentric Adjustment Disc), L-1018 (Eccentric Disc Shaft) or L-1020 (#6 Hose Clamp). The button head machine screw is 10-32 x 3/4. Page 4
You have a question the guide does not answerThe issue is not covered in the troubleshooting guideContact Lassco Wizer at 585-436-1934 or info@lasscowizer.com. Page 2

Frequently asked questions

How do I set up the LJ-4 table?

Attach the table (L-260A) to the table support using four flat head screws, eight stop nuts and four lock washers. See page 3.

How do I change the jogging speed?

Open the back panel, loosen the button head machine screw, rotate an adjustment disc on the disc shaft, then tighten the screw. See page 4.

What disc position gives the maximum jogging action?

When the screws are on the same side of the shaft, you get the maximum action. Opposite sides give the minimum action. See page 4.

What should I do if the machine does not turn on?

Check that the power cord is connected and the outlet is live. If that is fine, the power switch or motor may need replacing by a service technician. See page 5.

Why does the motor run but the paper does not jog?

The Torque Tube may be worn or broken, or the screw on the eccentric adjustment disc may be loose. See page 5.