

Page 1 of 5

Text on page 2
LasscoJog LJ-6 Paper Jogger
Serial Number: Date of Purchase: Dealer: Address:
Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference.
Telephone Number:
485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com info@lasscowizer.com
Page 2 of 5

Text on page 3
Instructions
Please remove and inspect the following items.
L-260A: Table Assembly (1)
8-32 x 1 Flat Head Screws (4)
#8 Lock Washers (4)
8-32 Stop Nut (8)
Setting Up Your Machine
Attach the Table (L-260A) to the Table Support using four (4) 8-32 x 1 Flat Head Screws, eight (8) 8-32 Stop Nuts, and four (4) #8 Lock Washers.
Step #1 Insert the four (4) Flat Head Screws through the front of the Table as shown.
Step #2 Place the Flat Head Screws through the holes of the Table Support.
Step #3 Attach the first Stop Nut and tighten.
Step #4 Place a Lock Washer over the screw.
Step #5 Attach the second Stop Nut and tighten.
Step #6 Repeat steps 3 - 5 on the remaining screws.
Page 3 of 5

Text on page 4
Instructions
Adjusting the Jogging Speed
To change the Jogging action:
Step #1 Open the back panel on the rear of the machine by removing the two bottom screws and flipping the cover up as shown in the rear view.
Step #2 Loosen the Button Head Machine Screw and rotate one of the Adjustment Discs attached to the Disc Shaft extending from the motor .
Step #3 Tighten down the Machine Screw.
L-1020: #6 Hose Clamp
L-1017: Eccentric Adjustment Disc
10-32 Screw x 3/4 Button Head Machine Screw
L-1018: Eccentric Disc Shaft
3/8” ID x 3/4” OD Fiber Washer
Note:
When the screws are located opposite each other on the shaft, the minimum action is obtained. When the screws are located on the same side of the shaft, the maximum action is obtained. Normal action is obtained when the screws are 80 to 90 apart.
Page 4 of 5

Text on page 5
Trouble Shooting Guide
Problem
Cause
Correction
Machine does not turn on.
Machine is not plugged in or there is no electricity to the outlet.
Make sure the power cord is connected correctly and that the outlet is live.
Power switch is faulty.
Contact a service technician to replace the power switch.
Motor has burned out.
Contact a service technician to replace the motor.
The Torque Tube (L-1019) has worn out or broken.
Replace the Torque Tube.
The screw on the Eccentric Adjustment Disc (L-1017) has come loose allowing the disc to shift.
Access the Adjustment Discs and tighten down the screw as shown on page 1.
The motor turns on but the machine does not jog as desired.
Page 5 of 5 · End of manual
Quick start
- Read first: Read all instructions before using the machine and keep them for later.
- Check the parts: Remove and inspect the table assembly (L-260A), 4 flat head screws, 4 lock washers and 8 stop nuts.
- Attach the table: Attach the table to the table support with the 4 flat head screws, 8 stop nuts and 4 lock washers.
- Fit the screws: Put the screws through the front of the table, then through the holes in the table support. Add a stop nut and tighten, add a lock washer, then add the second stop nut and tighten. Repeat on the other screws.
- Adjust the jogging: Open the back panel by removing the two bottom screws and flipping the cover up. Loosen the button head machine screw and rotate an adjustment disc on the disc shaft.
- Set the action: Screws opposite each other give minimum action. Screws on the same side give maximum action. About 80 to 90 apart gives normal action. Tighten the machine screw.
- If it will not start: Check that the power cord is connected and the outlet is live.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine does not turn on | The machine is not plugged in or the outlet has no electricity. | Make sure the power cord is connected correctly and that the outlet is live. Page 5 |
| Machine does not turn on | The power switch is faulty. | Contact a service technician to replace the power switch. Page 5 |
| Machine does not turn on | The motor has burned out. | Contact a service technician to replace the motor. Page 5 |
| Motor runs but the machine does not jog as desired | The Torque Tube (L-1019) has worn out or broken. | Replace the Torque Tube. Page 5 |
| Motor runs but the machine does not jog as desired | The screw on the Eccentric Adjustment Disc (L-1017) has come loose and the disc shifted. | Access the adjustment discs and tighten down the screw. Page 5 |
Frequently asked questions
How do I set up the LJ-6 table?
Attach the table (L-260A) to the table support using four flat head screws, eight stop nuts and four lock washers. See page 3.
How do I change the jogging speed?
Open the back panel, loosen the button head machine screw, rotate an adjustment disc on the disc shaft, then tighten the screw. See page 4.
What disc position gives the maximum jogging action?
When the screws are on the same side of the shaft, you get the maximum action. Opposite sides give the minimum action. See page 4.
What should I do if the machine does not turn on?
Check that the power cord is connected and the outlet is live. If that is fine, the power switch or motor may need replacing by a service technician. See page 5.
Why does the motor run but the paper does not jog?
The Torque Tube may be worn or broken, or the screw on the eccentric adjustment disc may be loose. See page 5.
