Lassco Wizer LasscoJog LJ-8 Flat Top Paper Jogger Operator Manual, page 1

Page 1 of 4

Lassco Wizer LasscoJog LJ-8 Flat Top Paper Jogger Operator Manual, page 2
Text on page 2

LasscoJog LJ-8 Paper Jogger

Serial Number: Date of Purchase: Dealer: Address:

Before operating this equipment, please read these instructions completely and keep these operating instructions for future reference.

Telephone Number:

485 Hague Street, Rochester, NY 14606 U.S.A. Tel: 585-436-1934 Fax: 585-464-8665 www.lasscowizer.com info@lasscowizer.com

Page 2 of 4

Lassco Wizer LasscoJog LJ-8 Flat Top Paper Jogger Operator Manual, page 3
Text on page 3

Instructions

Setting Up Your Machine

Your LJ-8 LasscoJog Paper Jogger comes ready to use. Simply plug in the power cord and turn on the machine.

Adjusting the Jogging Speed

To change the Jogging action, access the adjustment discs on the underside of the machine as shown. Loosen Button Head Machine Screw and rotate one of the Adjustment Discs attached to the Disc Shaft extending from the Motor . Tighten down the Machine Screw.

L-1020: #6 Hose Clamp

L-1017: Eccentric Adjustment Disc

10-32 Screw x 3/4 Button Head Machine Screw

L-1018: Eccentric Disc Shaft

3/8” ID x 3/4” OD Fiber Washer

Note:

When the screws are located opposite each other on the shaft, the minimum action is obtained. When the screws are located on the same side of the shaft, the maximum action is obtained. Normal action is obtained when the screws are 80 to 90 apart.

Page 3 of 4

Lassco Wizer LasscoJog LJ-8 Flat Top Paper Jogger Operator Manual, page 4
Text on page 4

Trouble Shooting Guide

Problem

Cause

Correction

Machine does not turn on.

Machine is not plugged in or there is no electricity to the outlet.

Make sure the power cord is connected correctly and that the outlet is live.

Power switch is faulty.

Contact a service technician to replace the power switch.

Motor has burned out.

Contact a service technician to replace the motor.

The Torque Tube (L-1019) has worn out or broken.

Replace the Torque Tube.

The screw on the Eccentric Adjustment Disc (L-1017) has come loose allowing the disc to shift.

Access the Adjustment Discs and tighten down the screw as shown on page 1.

The motor turns on but the machine does not jog as desired.

Page 4 of 4 · End of manual

Quick start

  1. Read first: Read the instructions completely before you operate the machine. Keep them for later.
  2. Ready to use: The LJ-8 comes ready to use.
  3. Plug in: Plug in the power cord.
  4. Turn on: Turn on the machine.
  5. Adjust the jogging action: Reach the adjustment discs on the underside. Loosen the button head machine screw, rotate one of the adjustment discs on the disc shaft, then tighten the screw.
  6. Choose the action level: Screws on opposite sides of the shaft give minimum action. Screws on the same side give maximum action. Screws 80 to 90 degrees apart give normal action.

Troubleshooting

ProblemLikely causeFix (from the manual)
Machine does not turn onThe machine is not plugged in or there is no power at the outlet.Make sure the power cord is connected correctly and that the outlet is live. Page 4
Machine does not turn onThe power switch is faulty.Contact a service technician to replace the power switch. Page 4
Machine does not turn onThe motor has burned out.Contact a service technician to replace the motor. Page 4
Motor turns on but the machine does not jog as desiredThe Torque Tube (L-1019) has worn out or broken.Replace the Torque Tube. Page 4
Motor turns on but the machine does not jog as desiredThe screw on the Eccentric Adjustment Disc (L-1017) has come loose and the disc shifted.Access the adjustment discs and tighten the screw. Page 4

Frequently asked questions

Does the LJ-8 need assembly?

No. It comes ready to use. Plug in the power cord and turn on the machine. See page 3.

How do I change the jogging action?

Loosen the button head machine screw on the underside, rotate an adjustment disc on the disc shaft, then tighten the screw. See page 3.

How do I get minimum or maximum jogging action?

Put the screws on opposite sides of the shaft for minimum action. Put them on the same side for maximum action. Normal action is 80 to 90 degrees apart. See page 3.

Why will my paper jogger not turn on?

The machine may be unplugged or the outlet has no power. The power switch may be faulty or the motor may have burned out. Call a service technician for those two. See page 4.

What if the motor runs but the jogger does not jog?

The Torque Tube may be worn or broken, or the screw on the Eccentric Adjustment Disc may be loose. Replace the tube or tighten the screw. See page 4.