Ledco Premier 25" Laminator Manual, page 1

Page 1 of 39

Ledco Premier 25" Laminator Manual, page 2

Page 2 of 39

Ledco Premier 25" Laminator Manual, page 3

Page 3 of 39

Ledco Premier 25" Laminator Manual, page 4

Page 4 of 39

Ledco Premier 25" Laminator Manual, page 5

Page 5 of 39

Ledco Premier 25" Laminator Manual, page 6

Page 6 of 39

Ledco Premier 25" Laminator Manual, page 7

Page 7 of 39

Ledco Premier 25" Laminator Manual, page 8

Page 8 of 39

Ledco Premier 25" Laminator Manual, page 9

Page 9 of 39

Ledco Premier 25" Laminator Manual, page 10

Page 10 of 39

Ledco Premier 25" Laminator Manual, page 11

Page 11 of 39

Ledco Premier 25" Laminator Manual, page 12

Page 12 of 39

Ledco Premier 25" Laminator Manual, page 13

Page 13 of 39

Ledco Premier 25" Laminator Manual, page 14

Page 14 of 39

Ledco Premier 25" Laminator Manual, page 15

Page 15 of 39

Ledco Premier 25" Laminator Manual, page 16

Page 16 of 39

Ledco Premier 25" Laminator Manual, page 17

Page 17 of 39

Ledco Premier 25" Laminator Manual, page 18

Page 18 of 39

Ledco Premier 25" Laminator Manual, page 19

Page 19 of 39

Ledco Premier 25" Laminator Manual, page 20

Page 20 of 39

Ledco Premier 25" Laminator Manual, page 21

Page 21 of 39

Ledco Premier 25" Laminator Manual, page 22

Page 22 of 39

Ledco Premier 25" Laminator Manual, page 23

Page 23 of 39

Ledco Premier 25" Laminator Manual, page 24

Page 24 of 39

Ledco Premier 25" Laminator Manual, page 25

Page 25 of 39

Ledco Premier 25" Laminator Manual, page 26

Page 26 of 39

Ledco Premier 25" Laminator Manual, page 27

Page 27 of 39

Ledco Premier 25" Laminator Manual, page 28

Page 28 of 39

Ledco Premier 25" Laminator Manual, page 29

Page 29 of 39

Ledco Premier 25" Laminator Manual, page 30

Page 30 of 39

Ledco Premier 25" Laminator Manual, page 31

Page 31 of 39

Ledco Premier 25" Laminator Manual, page 32

Page 32 of 39

Ledco Premier 25" Laminator Manual, page 33

Page 33 of 39

Ledco Premier 25" Laminator Manual, page 34

Page 34 of 39

Ledco Premier 25" Laminator Manual, page 35

Page 35 of 39

Ledco Premier 25" Laminator Manual, page 36

Page 36 of 39

Ledco Premier 25" Laminator Manual, page 37

Page 37 of 39

Ledco Premier 25" Laminator Manual, page 38

Page 38 of 39

Ledco Premier 25" Laminator Manual, page 39

Page 39 of 39 ยท End of manual

Quick start

  1. Prepare the machine: Put the Premier 25 on a level surface and remove all straps, tape and ties and the protective paper on the safety shield. Make sure the power cord is not under the machine.
  2. Power on: Confirm the heat, fan and drive switches are off, then plug into a working outlet of at least 15 amps. Turn the heat on. The heat lamp stays lit until the set temperature is reached.
  3. Set temperature: Press the red button once to see the set value, then press it again to raise the value. Press the blue button to lower it. The factory setting is about 240 degrees F for low-temperature 3 mil film.
  4. Load the film: Center a roll on each supply mandrel and line the rolls up with the score marks. Run the film under the top idler bar and over the top heat shoe with the shiny side against the shoe. Lay the bottom film against the top film.
  5. Thread the machine: Unwind each roll about a half turn, slide on the feed tray, and flip the safety shield down. Close the rollers with the large knob on the right, push a threading card into the nip, press forward, and press stop when the card exits the back.
  6. Set tension and warm up: Start with three or four turns of tension on each knob. The machine is ready in about 10 minutes. Turn the fans on for 3 mil or thicker film and let at least 10 inches of film run before feeding items.
  7. Shut down: Turn the fan and heat off, unplug the machine, and leave the rollers open.

Troubleshooting

ProblemLikely causeFix (from the manual)
Film wraps around the laminating rollers while hotA film roll ran out or the film end got caught, so exposed adhesive stuck to the rollers.Leave the heat on and remove the feed tray. Cut the film in front of the idler bars, hold both ends together, and run the drive in reverse at very low speed while pulling the film off. Never cut it off with a knife. Page 29
Film is not sticking or comes off laterThe temperature is too low. Thin 1.5 mil film run too slowly can cool too much, and thicker film run too fast may not reach its melt point.Raise the heat. For posters with 1.5 mil film, about 320 to 340 degrees F usually works. Slow down thick film. Page 31
Large oily-looking spot near the leading edgeExtra adhesive pooled on the film over the shoes while the machine sat heated and idle.Let a few inches of film run through before feeding your work. Test with a sample first. Page 31
Milky, hazy line about an inch wide after warm-upThe rollers are not evenly heated.While warming up, keep the rollers open and run the forward drive at low speed. Page 31
Loud squealing during laminationToo much supply roll tension or heat, or build-up on the heat shoes.Use the least tension that removes wrinkles, avoid extra heat, and clean the heat shoes. If it stays loud, try a different film. Page 32
No power to the laminatorA dead outlet or a loose power cord is the most common cause.Check the outlet for power and make sure both ends of the cord are seated firmly. Page 32
Wavy or rippled film near the centerHeat wrinkles from too much temperature or speed for that film.Slow the motor, lower the temperature to a suitable level, and use the fans with 3 mil or thicker film. Page 32

Frequently asked questions

What is the warranty on the Ledco Premier 25?

It is guaranteed against defects in material and workmanship for one year after the ship date. Normal wear parts such as rubber rollers and heat shoe coatings are not covered. See page 12.

What size and thickness can it laminate?

It laminates up to 25 inches wide and items up to 1/8 inch thick, using film up to 10 mil. See page 8.

What power does it need?

It runs on 110V and draws 15 amps, so use an outlet of at least 15 amps. A 220V version is listed as optional. See page 8.

What should I not laminate?

Do not laminate thermal paper such as fax paper, because it turns black. Remove paper clips and staples, and avoid one-of-a-kind documents and collectibles. See page 3.

What temperature and speed should I use for 3 mil film?

A standard 3 mil film is applied at about 280 degrees F, and typical speed is about five feet per minute. Use the fans with 3 mil or thicker film. See page 11.