Logan 40" Team System Plus Mat Cutter - 440-1 Manual, page 1

Page 1 of 2

Logan 40" Team System Plus Mat Cutter - 440-1 Manual, page 2
Text on page 2

over hole over thread

Board to Size

. Be sure sharp blade is facing edge of downward. Re The Mat Knife as se is used for trim m bl e blade to double Cover Plate. Ad ming matboard to size for the ou just thick, standard or foamboard tside dimensio or safety setting to lock in place. ns. The Mat Kn . Tighten nut settings: Doub ife has three le thick mat bo ard/foam board

2. Bevel Cutte standard (middl (fully extended r e setting) or sa ), fe ty setting (fully Remove the Bl

1. Use a Slip ade Holding Sc retracted). Sheet rew from the fro Cutter. Remove nt of the Bevel Before cutting, one blade from be sure to use the package of blade down on a slip sheet of

5. Slide the the same size or to the FRONT of Preparation Operation scrap matboard larger than the th e chrome Blade sharp edge dow piece you are go underneath the Holder, n, until the botto ing to cut matboard you w m right hand co Inserting blade enters Blades Mat ill be cutting. Th into the Blade rner of the provid Knife es a place fo e slip sheet Slot and the ho Preparation Operation r the blade tip es up Knife

1. lin Mat le in the blade with the hole in to su go rface yo Cutting a u Board so it won’t cut the chrome Blad are cutti to ng Size into the Bl Remove ade Hold one on and also he e Ho nut blade of 5. Remove Cover ing Sc lder. and Inserting Blades to get nice stra Mat Repl rew from lps stabilize th Knife ace in ho pack le and re-tighte ig ht e blade The Mat Knife is used for trimming matboard or foamboard cu ts . n. sharp edge of Plate. Align blade thread. Be sure

1. hole Mat over Knife

2. Mea Cutting a Board The to Size to su size dimensions. Mat Knife has three rin for g the outside Caut blade facing Cover Plate. ion! is ! M Remove Reassemble one blade from pack of 5. Adjust Remove nut and Cover at Cu downward. Draw tting pencil Double settings: thick mat board/foam board (fully extended), Blades are Sh lin es on ba The Mat Knife is used for trimming matboard or foamboard ck of arp setting. blade to double thick, standard or safety Tighten mat Plate. Align blade hole over thread. Be nut sure sharp of (middle board setting the edge channe at desir standard or safety (fully l side of th setting) ed siz retracted).

e. Plac The to size for the outside dimensions. e ra e Mat Knife has three il ed ge al to lock in place. blade is facing downward. Reassemble Cover Plate. pencil Adjust on g th e left mat Fig. Sheet sid board/foam e of the settings: Double thick board (fully extended),

1. Use lin a e. Slip blade to double thick, standard or safety setting. Tighten

2. Bevel Cutter

3. Prec ut nut standard setting) safety setting (fully retracted). Before cutting, be sure to use (middle a slip sheet of or scrap matboard Remove the Blade to Holding lock in Screw place. from the front of the Bevel Hold the the same or 1. pl larger than the Sheet piece you are going to cut rail fir size mly in Use a Slip ac e with your left ha Cutter. Remove 2. one Bevel blade Cutter from the package of 5. Slide the hand underneath hold the Mat the Kn matboard you will be be sure cutting. The nd. to With yo a slip ur slip use sheet ife Before rig sheet vertica cutting, ht of scrap matboard blade down onto the FRONT the of Blade the chrome Blade Holder, l so tip degr of ee that to th go an Bevel e ha Remove Holding Screw from the front the provides a tti place for the blade so nd it than cut into you the are going to cut gle pu le won’t is ng at th a the same size or larger the piece e tip ag sharp edge down, until the Remove bottom one right blade hand from corner the ai and nst th e St If yo ra Cutter. the of package of

5. u Slide the ig surface you are cutting on also helps stabilize the blade ht Ed you are cutting acro underneath the matboard ge . Fi g. will be cutting. The slip sheet ss a sheet of m blade enters into the Blade Slot onto and the the FRONT hole in of the the blade blade Holder, blade down chrome Blade atboar to get nd nice cuts. a place beyo d, the sim blade the straight pl provides for tip to go so it won’t cut into the y top edge st ar t lines up with the hole in the chrome Blade Holder. Replace th e of the board an m 2. plet sharp edge down, until the bottom right hand co corner d pull th el of y the through. surface you are cutting on e and Measuring Mat also Knife helps stabilize the blade Blade Holding Screw in hole and re-tighten. blade enters into the Blade Slot and the 4. hole Cu in tti the blade pencil lines on ng Draw to back get nice straight cuts. of matboard at desired size. Place lines up with the hole in the chrome Blade Holder. Replace Draw th the e M channel of Measuring the rail edge along the left side of the at Knife side tow

2. ar d you along the Caution!! Mat Cutting Sharp Blade Blades Holding are Screw in hole and re-tighten. keeping pencil Straight Edge consta line. nt pr Fig. essu 1 re Draw on back of matboard at desired size. Place on the pencil Straig lines pressure on the ht Edge and do M at w Kn nwar ife. the

3. Precut side of the rail edge along d the left side of the Fig. channel Caution!! Mat Cutting Blades are Sharp the rail firmly in place line. with Fig. your pencil 1 left hand. With your right WARNING! Hold Be careful w hen Knife hold the Mat vertical so that the handle is at a 45 knife mat so that hand reache s the end of th it do not ”j 3. Precut ump” the e Fig. 2 degree es angle putting tip against Edge. to w ar d yo Hold the rail firmly in Straight place with your left hand. With your right u. the If you are cutting across a sheet matboard, simply so start hand hold the of Mat Knife vertical that the the handle is at a 45 beyond the top edge angle of the putting board and pull against the Mat the Knife

Operati blade

degree the tip Straight Edge. Fig. 2 o n completely through. If you are cutting across a sheet of matboard, simply start the Bevel Cutt er

4. Cutting blade beyond the top edge of the board and pull the Mat Knife Cutting a Si Draw Mat Knife completely toward you through. along the Straight Edge ngle the Mat pressure on the Straight Edge and downward

1. Using the keeping scale sid constant 4. Cutting e on of the Stra Mat ight Knife. Fig. Edge mat for the pressure , Fig. m Mat ar 3 k 2 th e back the Knife toward exact border yo Draw of the you along the Straight Edge u want.

2. Place the m keeping constant pressure on the Straight Edge and downward at face do Be WARNING! knife reaches the end of the wn careful on th pressure e Sl when Matboard the Mat Knife. Fig. 2 ip Sh on Edge EXACTLY eet. toward Plac e th you. e Straight mat so on that not ”jump” the it le does ft ha nd border so th edge of the chan at the outside nel is lined up al on WARNING! Be careful M g ak the pencil line. when knife reaches the end of the e sure that the Trouble Shooting bulk of th e m so at is mat that it e does ”jump” toward you. of the Straight to th right not hand side Edge. Having th Bevel Cut has a Rough Edge Operation e mat on the le Straight Ed ge will result in ft side of the

1. You may need to change your blade more often. Dull blades drag a reversed beve 302 Beve Bevel l cut. Attach th l Cutter to Cutter through the mat instead of cut. the straight ed e ge by fitting th lon guides over

2. Change your Slip Sheet. Cutting over the same area on the ny Slip Operation e black th a e Single ra Cutting Mat ise d edge of the ch Mat Cutter so Sheet repeatedly can cause rough cuts. annel. Position that the silver Bevel Cutter the back of the in side dicato Not Cutting Through the Mat bottom inte 1. rsec Using the of r Straight the line lines Edge, up w mark ting penc scale ith the il

1. Keep even downward pressure on the Chrome Blade Holder lin e. Fi border g. mat for the exact you want. Cutting a Single Mat 3.

Hold to downwar throughout the cut. Letting pressure off will allow the blade d pres re on th hand. Place 2. the Place su raight the come out of the mat. mat face down on Sheet. Place the Straight Ed the

  1. e St Using scale Edge, mark the back of the ge w Slip ith side thumb the yo ur of le Straight of your right ha ft the outside
  2. Check your blade depth. Insufficient blade depth can result on in th unnd EXACTLY on the left hand border so that e retractab Edge on mat for the exact border you want. th e th umb divot le Blade Holder dercut mats.To adjust the blade depth on the Bevel Cutter, turn the and is mat.

Matboard plun edge of the channel lined pencil line. Fig. 4 ge up e along bl face ade the in down to th on the Slip Sheet. Place the Straight

  1. Place the th mat screw on the underside of the cutting head clockwise to decrease Make sure that the bulk of the mat is to the e right hand side 4.

Ke Slip Shee or ep counter-clockwise to increase the amount of the exposed blade. in g downward pr Edge EXACTLY on the left hand border so that the outside t sure on Edge. Straight the mat on the left side of the the edge Overcuts In Corners the Bevel Cutte of the es Bl Having ade of Ho Matboard the channel is lined up along the pencil line. Fig. 4 lder, r Straight slide bevel away fro Edge m

1. Check your blade depth. Extra blade depth can cause the blade will result in a reversed cut. Attach the yo u until Make intersec the sil sure ver lin that the it bulk of the mat is to the right hand side e on e up Bevel tip to cut past the marked lines producing an overcut. Using the ts with th 302 per pe Cutter ncil lin to straight edge by fitting the black

e. of the Be the dow blade su re to keep nward pressure Straight Edge. en Having the mat on the left side of the recessed screw on the bottom of the Bevel Cutter, adjust the . Fig. nylon guides channel. Position the 6 over the raised edge of ev the tip to allow for 1/8” exposure. The blade should just score into the Straight Edge will result in a reversed bevel cut. Attach the

5. Use your th umb to Mat so that the silver indicator line lines up with the pull Cutter surface of the Slip Sheet. the Blad Bevel Cutter to the straight edge by fitting the black e Hold 302 posit n so the bottom er ba ck line. into Fig. pencil blade is re intersecting the up To adjust the blade depth on the Bevel Cutter, turn the screw io on m ov over the raised edge of the channel. Position the ed from nylon st ep counthe m guides s for the remai at . the underside of the cutting head clockwise to decrease or Re pe at ning downward ese Edge th 3. Hold pressure on the Straight your left re e sides. Co Mat Cutter so that th the silver with indicator line lines up with the have just cut yo ng ter-clockwise to increase the amount of the exposed blade. ra tu lations! You ur fir st mat hand. Place of your right hand on the thumb . the thumb bottom intersecting pencil line. Fig. divot Hooks or Curves in Cut on the retractable Blade Holder and plunge the blade into the

1. Check your blade depth. Extra blade depth can cause the blade tip

3. Hold downward pressure on the Straight Edge with your left to flare out producing a hook or curve. Using the recessed screw mat. hand. Place the thumb of your right hand on the thumb divot on the bottom of the Bevel Cutter, adjust the blade tip to allow for

4. Keeping downward on pressure on the Blade the retractable Blade Holder, Holder slide and plunge the blade into the 1/8” exposure. The blade score into the surface of the Loga should n Gra just ph Pro Bevel the Bevel Cutter away from you until the silver line on it duct Cutter, Slip Sheet. To adjust the blade depth ic on the turn the mat. s Inc., 1100 B row intersects n Street, with screw on Slip the Sheet underside of the cutting head clockwise to decrease or the co upper pencil line. Be sure to keep even W 4. au nda, downward Keeping on the Blade Holder, slide IL 60 4 pressure counter-clockwise to increase the amount of the exposed blade. 847-526-5515 downward pressure.

6 Cutter 08

the Fig. Bevel away from you until the w silver on ng it

2. Change the blade. A dull blade will flare out causing a hook or curve. ww line .loga ra A NOTE ON BLADES: No two Slip blades will have the same lifespan. Al- Sheet

5. Use your thumb to intersects pull the Blade back pencil into the up Be sure to keep even ph ic .c om with Holder the upper line. ways start with a new blade before each project to ensure best results. position so the blade is removed from the mat. downward pressure. Fig. 6 Repeat these steps for the remaining three sides. Congratulations! You

5. Use your thumb to pull the Blade Holder back into the up have just cut your first mat. position so the blade is removed from the mat. Repeat these steps for the remaining three sides. Congratulations! You have just cut your first mat.

Team System Plus Instruction Manual Team System Plus Instruction Manual

Model 424-1 | 440-1

Model 424-1 | 44

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

L405N rev 1 3-12

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic

Page 2 of 2 ยท End of manual

Quick start

  1. Always use a slip sheet of scrap matboard the same size or larger than the piece you are cutting.
  2. To cut a board to size, draw pencil lines on the back, place the straight edge on the line, hold the mat knife vertical at a 45 degree angle and pull it toward you with steady pressure.
  3. For a single mat, mark the border on the back of the mat with the straight edge scale and place the mat face down on the slip sheet.
  4. Line up the left edge of the channel exactly on the pencil line, with the bulk of the mat to the right of the straight edge.
  5. Attach the 302 bevel cutter, line its silver indicator line up with the bottom pencil line, and plunge the blade with your thumb.
  6. Slide the cutter away from you until the silver line meets the upper pencil line, lift the blade out, and repeat on the other three sides.

Troubleshooting

ProblemLikely causeFix (from the manual)
Bevel cut has a rough edgeA dull blade, or cutting over the same area of the slip sheet repeatedly.Change the blade more often and change your slip sheet. Page 2
Not cutting through the matPressure let off during the cut, or not enough blade depth.Keep even downward pressure on the blade holder throughout the cut; turn the screw under the cutting head counter-clockwise to expose more blade. Page 2
Overcuts in cornersToo much blade depth.Use the recessed screw on the bottom of the bevel cutter to set about 1/8" exposure, so the blade just scores the slip sheet. Page 2
Hooks or curves in the cutToo much blade depth, or a dull blade flaring out.Reduce blade exposure to about 1/8" and change the blade. Page 2
Bevel is reversedThe mat was placed on the left side of the straight edge.Keep the bulk of the mat to the right of the straight edge. Page 2

Frequently asked questions

How deep should the bevel blade be set?

About 1/8" exposure, so the blade just scores the surface of the slip sheet. See page 2.

What are the mat knife blade settings?

The mat knife has three settings: double thick mat board/foam board (fully extended), standard (middle) and safety (fully retracted). See page 2.

Why do I need a slip sheet?

It gives the blade tip a place to go so it won't cut into your work surface, and helps stabilize the blade for straight cuts. See page 2.

How often should I change the blade?

No two blades last the same; Logan recommends starting each project with a new blade. See page 2.