

Page 1 of 3

Text on page 2
Instruction Manual
8-Ply Mat Cutter
Model 5000
Identification
CAUTION!!
MAT CUTTING BLADES ARE SHARP
Start & Stop Lines
8-Ply Bevel Cutting Instructions
NOTE: Use only special 8-Ply blade #271. It has only one sharp, beveled edge. DO NOT USE #270 which looks similar but has two beveled edges. The #270 blade will not cut 8-Ply effectively (Fig. 1).
NOTE: Only one corner of blade #271 can be used (Fig. 2).
- Loosen blade knob and remove cartridge.
- Set blade onto blade slide, being careful of orientation of edge bevel (Fig. 3).
- Insert blade slide into cutting head (Fig. 4).
- Tighten blade knob.
Blade Slide
#271 SINGLE BEVEL 8-PLY BLADE
NOTE: Standard 8-Ply depth setting is aligning end of blade with end of slide (Fig. 5).
- Set cutter onto 8-Ply mat board with blade overhanging edge.
- Depress blade fully.
- Corner of blade tip edge should score the slip sheet past top of bevel edge (Fig. 6).
- To adjust depth, loosen blade knob and turn depth adjustment screw.
NOTE: When reducing depth, you will have to push blade back with your finger.
- Retighten blade knob.
#271 BLADE
ONLY USE THIS CORNER
SLIP SHEET
8-PLY MAT
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com
Page 2 of 3

Text on page 3
Instruction Manual
8-Ply Mat Cutter
Model 5000
Cutting an 8-Ply Mat
On back of mat, draw pencil lines for location of opening (Fig. 7). Place your mat (color side down) on a slip sheet (scrap matboard) which must be larger than the mat. Align straight edge on left side of line or slide under guiderail and up against the mat guide and squaring arm. Hook cutter onto rail edge and align GREEN scribe line with top pencil line (Fig. 8). With left hand, depress the anti-crawl pin and firmly pivot the blade holder down into the mat (Fig. 9). Pull cutter along rail until the red scribe line meets the bottom pencil line (Fig. 10). Pivot blade out of mat. Repeat remaining three sides (Fig. 11).
INCH
Use two hands to cut. Setting blade depth too deep can result in blade tip chipping off. Change blade often. Use one blade corner when cutting 8-Ply. If you do not cut through the mat, repeat cut. If your overcuts are too long or too short, start & stop inside or outside start/ stop lines to adjust.
Adjust Nylon Guides (use Phillips Screwdriver)
To improve straightness of cut, you may need to adjust the guides fit on guiderail.
- Hook cutter onto rail.
- Loosen guide screws (Fig 12).
- Squeeze guide against rail.
- Retighten guide screws.
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 847-526-5515 LoganGraphic.com
Page 3 of 3 · End of manual
Quick start
- Use the right blade: Use only the special 8-Ply blade #271. Do not use #270, which has two beveled edges and will not cut 8-Ply well.
- Load the blade: Loosen the blade knob and remove the cartridge. Set the blade onto the blade slide with the bevel edge in the correct direction, insert the slide into the cutting head and tighten the knob.
- Set the depth: The standard 8-Ply depth is the end of the blade lined up with the end of the slide. To adjust, loosen the blade knob and turn the depth adjustment screw.
- Mark the mat: Draw pencil lines on the back of the mat for the opening. Place the mat color side down on a slip sheet that is larger than the mat.
- Position the cutter: Align the straight edge on the left side of the line. Hook the cutter onto the rail edge and line up the GREEN scribe line with the top pencil line.
- Make the cut: Press the anti-crawl pin with your left hand and pivot the blade holder down into the mat. Pull the cutter along the rail until the red scribe line meets the bottom pencil line, then pivot the blade out.
- Repeat: Repeat for the remaining sides of the opening.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Cut does not go through the mat | The blade depth may be too shallow or the blade is dull. | Repeat the cut. Change blade often. Page 3 |
| Blade tip chips off | The blade depth is set too deep. | Reset the depth so the blade end lines up with the end of the slide, and change blade often. Use two hands to cut. Page 3 |
| Overcuts are too long or too short | The start and stop points are off the start/stop lines. | Start and stop inside or outside the start/stop lines to adjust. Page 3 |
| Cut is not straight | The nylon guides do not fit the guiderail correctly. | Hook the cutter onto the rail, loosen the guide screws, squeeze the guide against the rail and retighten the screws. Use a Phillips screwdriver. Page 3 |
| 8-Ply mat does not cut well | The wrong blade is installed. | Use only blade #271 and use only one corner of it. Blade #270 will not cut 8-Ply effectively. Page 2 |
Frequently asked questions
What blade does the Logan 5000 use?
Use only the 8-Ply blade #271, which has one sharp beveled edge. Do not use #270. See page 2.
What is the standard blade depth for 8-Ply?
The standard setting is the end of the blade lined up with the end of the blade slide. To adjust, loosen the blade knob and turn the depth adjustment screw. See page 2.
Why is my cut not straight?
The nylon guides may need adjusting on the guiderail. Loosen the guide screws, squeeze the guide against the rail and retighten. See page 3.
How do I fix overcuts that are too long or short?
Start and stop inside or outside the start/stop lines to adjust. See page 3.
What do I put under the mat when cutting?
Place the mat color side down on a slip sheet of scrap matboard that is larger than the mat. See page 3.
