Logan F300-1 Picture Framing Studio Joiner Manual, page 1

Page 1 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 2
Text on page 2

PICTURE FRAMING

Studio Joiner

The model F300-1 Studio Joiner has been designed to economically and precisely drive V-nails into moulding corners to securely join them together. Simple and easy to use, this complete system produces strong, tight corners for high quality professional results. Accepts mouldings up to 2 1 / 2 " (64mm).

Producing professional quality picture frames is now easier than ever.

Reference Part No. L956N rev.1 Rev. 9/14

Page 2 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 3
Text on page 3

Identification

Support Rod

Lever

Depth Guage

Magnetic Tip

Beam

Levelers

Knob

V-Nails

Spring Button

Vise

Handle

Beam - Adjustable cross bar which contains lever and V-nail driver.

Magnetic Tip - Spring loaded pin attached to V-nail driver which V-nails set on.

Depth Gauge - Indicator connected to beam which adjusts beam to proper height for driving V-nail.

Knobs- allow beam to be moveable for adjustment.

Support Rods - Rods which set into base board and provide support for beam.

Vise - Used to secure moulding for corner joining.

Spacer

Handle - Used to tighten or loosen clamp jaw.

Spring Button - Press down and slide handle to quick adjust clamp jaw into position.

Spacer - Used for irregular shape moulding to provide solid surface for joining.

V-Nails - V-shaped fasteners used to hold moulding corners together.

Levelers - Small blocks designed to stabilize lengths of moulding extending off the board to help with beam height adjustment.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 3 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 4
Text on page 4

Parts List

Base Board

V-Nails

Lever Assembly

Spacer

Vise

Rod Washers

Rod

Wrench

Rod

Screws

Knobs

Levelers

Support Rods

Parts List

Base board

Knobs

Levelers

Lever assembly

Rod Screws

Rod Washers

Spacer

Support rods

Vise

V-nails

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 4 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 5
Text on page 5

Assembly Procedure

  1. Slide support rods into sleeves in board (Fig. 1).
  2. Attach support rods with rod screws and washers using rod wrench (Fig. 2).
  3. Slide lever assembly over support rods (Fig. 3).
  4. Screw knobs into lever assembly (Fig. 4).

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 5 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 6
Text on page 6

Preparation

A. Choose V-nail type, size and quality

1. V-nail Type

a. Hard Wood Nails - Used for very hard woods like oak and maple. Do not use on soft woods.

b. Soft Wood Nails - Used specifically for soft woods but can be used on hard woods.

2. V-nail Size

a. Choose a size nail that is at least 1/2 the moulding thickness.

3. Quality

a. Use at least two V-nails per joint. 1/4" to 1 3/4" wide moulding - 2 nails 2" to 2 1/2" wide moulding - 3 nails For information on how to purchase additional V-nails see page 10.

B. Clamp Moulding

✔ • Mark edge of miter to blend any gaps

in corner (Fig. 5) using a stain marker. Stain markers can be purchased at a hardware store. ✔ • Glue moulding miter for long lasting solid corners (Fig. 6).

  1. Adjust clamp jaw by pressing spring button and sliding handle (Fig. 7).
  2. Align moulding pieces in vise so top corner is square (Fig. 8).
  3. Do not overtighten. The moulding only requires enough clamping pressure to hold it still (Fig. 9).

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 6 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 7
Text on page 7

Preparation continued

  1. Moulding must have support for V-nail to drive into wood. Use the spacer when moulding is not even with horizontal plane (Fig. 10).
  2. With rubber edges facing up, place spacer between clamped moulding and base board (Fig. 11).

Spacer Needed

Horizontal Plane

Spacer Needed

No Spacer No Spacer Needed Needed

D. Adjust Beam Height

1. Turn clamped moulding over and lay on base board spacer (Fig. 12). If using spacer, position clamped moulding on spacer where V-nail is to be pressed in.

2. Line up depth gauge with vise post.

3. Loosen knobs and adjust beam so depth gauge lightly touches vise post (Fig. 13).

5. The depth gauge may be pivoted either to left or right to gain extra clearance.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 7 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 8
Text on page 8

Operation

A. Load V-Nail

1. Align V-nail around magnetic tip with beveled sharp edge of nail facing down (Fig. 14).

B. Press V-Nail

1. Press V-nail into inside corner first. Slide vise corner under magnetic tip and V-nail (Fig. 15).

2. Space V-nail 1/4” from inside corner (Fig. 16).

3. Press V-nail flush using lever (Fig. 17).

4. Load second V-nail.

5. Slide vise locating V-nail 1/2 distance between first V-nail and outer corner (Fig. 16).

6. Press V-nail flush using lever.

7. Repeat on other corners to complete.

✔ • Join sides of frames first. Then join halves

to finish (Fig. 18).

  • Always put longer length in vise on right

✔ hand side and shorter length on left hand

side .

  1. The Levelers can be deployed to help stabilize the moulding and or vise that extends past the edge of the board to allow proper setting of beam height (Fig. 19).

✔ • The Studio Joiner can easily join poly-

styrene and Emafil plastic mouldings by slowly but firmly pressing V-nails in. Note; these will bend if pressed in too fast.

Beveled Sharp Edge

Second

Nail

1/2 Distance

First Nail

1/4” (5mm)

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 8 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 9
Text on page 9

Operation Continued

C. To Join Multi Sided Frames Note; The steps below apply to all five sided, six sided and eight sided frames.

1. Once the frame has been ‘strap clamped’ (not provided) the Beam must be removed.

2. The clamped frame may now be placed over one of the Post’s (Fig. 20).

3. The Beam can now be replaced.

4. The Beam must have the correct height set by using the Vise that is currently not being used. Simply place the Vise upside down on the board and set height as described earlier in this manual (Fig. 21).

5. The V-Nails can now be pressed in, in the normal fashion (Fig. 22).

6. Once all the frame corners have at least two V-Nails, simply remove the Beam and remove the frame.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 9 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 10
Text on page 10

Trouble Shooting

V-nail is not driven in all the way.

Re-adjust depth setting. Refer to instructions.

Use correct size V-nail.

Joint opens up when driving V-nail in.

Use the spacer provided and position under where the V-nail is to be driven in.

Make sure the moulding is securely clamped in vise, and is square against the fence back.

Magnetic V-nail holder sticks in the shaft after insertion of V-nail.

Remove Beam to gain better access to magnetic V-nail holder and clean using solvent to remove glue residue.

Use less glue and have damp cloth on hand to clean up any squeeze out that occurs.

Frame does not assemble correctly.

Join sides of frame first, then join halves to finish. Always put longer length in vise on right hand side and shorter length on left hand side.

Make sure the two pairs are equal length.

Reduce the amount of glue in joint.

Check square cutting action of saw.

Use longer V-nails if possible.

Clamped moulding does not fit in between posts. Lift Beam off of support rods, and place vise with moulding in between support rods and then re-set beam height, to continue to press V-nail’s in.

Warranty

Logan Graphic Products, Inc. (“Logan”) warrants the Studio Joiner - Model F300-1, to be free from defects in parts and workmanship for a period of one year from the date of original purchase. Logan warrants that it will either repair or replace, at it’s sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 10 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 11
Text on page 11

L921N3-BO

L929L-BA

L929R-BA

Depth Gauge Screw 1

L929L-BA/ L929R-BA

Leveler Threaded Sleeve

L933B4/ L933TS

L933B4/L933TS*

L936N5

LWS-926N3*

L1402N-CA*

  • Items are only available as preassembled parts.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 11 of 12

Logan F300-1 Picture Framing Studio Joiner Manual, page 12
Text on page 12

Also ava ilableFromLoganGraphics

Logan Graphics Picture Framing System includes all the tools and accessories you need to produce professional quality frames including…

Precision Sander ELITE

Model F200-2 Sands miters to perfect 45° angle for tight, square frames

10 lb wheel Adjusts 45° left, 90° and 45° right Micro adjustment for perfect 45° Aluminum oxide sand paper with life extending bar Sand up to 2 1/2“ (64mm) mouldings Dust removal bar

PROJoiner Model F300-2

Heavy duty professional-style joiner for precise corner joints

V-nail alignment pins* Drives all V-nail sizes Fits mouldings up to 2 1 /2" (64mm) Can drive two nails at once

replacement V-Nails Find replacement V-nails where you purchased your tool.

Fittingtool Model F400-1

Drives brads or point inserts into wood frames to hold materials in place

Drives four different inserts No slipping or bending Removes inserts Easy adjust foot Use on hard or soft woods Patented rotating insert holder Proper drive angle assured No guessing or skill required

1/4” (7mm), 3/8” (10mm) and 1/2 (12mm)

sizes are available for both soft and hard wood

applications, packaged in quantities of 200.

dual drive ELITE Model F500-2 Spring-loaded action drives both rigid and flexible points to secure artwork in both hard and softwood frames

Holds stacks of flexible or rigid points for fast productive framing Comfortable handle grip and smooth firing action Must-have for artists, framers and hobbyists! For best results, using only authentic Logan points

For more information, including where to buy Logan Framing

Products, Please visit us at www.logangraphic.com or

call Toll Free (800) 331 6232.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 12 of 12 ยท End of manual

Quick start

  1. To Join Multi Sided Frames Note; The steps below apply to all five sided, six sided and eight sided frames.
  2. The clamped frame may now be placed over one of the Post’s (Fig. 20).
  3. The Beam can now be replaced.
  4. The Beam must have the correct height set by using the Vise that is currently not being used. Simply place the Vise upside down on the board and set height as described earlier in this manual (Fig. 21).
  5. The V-Nails can now be pressed in, in the normal fashion (Fig. 22).
  6. Once all the frame corners have at least two V-Nails, simply remove the Beam and remove the frame.

Troubleshooting

ProblemLikely causeFix (from the manual)
V-nail is not driven in all the wayThe depth setting is wrong, or the V-nail is the wrong size.Re-adjust the depth setting and use the correct size V-nail. Page 10
Joint opens up when the V-nail goes inThe moulding is not supported or not held square.Use the spacer under the spot where the V-nail goes in. Make sure the moulding is clamped tightly and square against the fence back. Page 10
Magnetic V-nail holder sticks in the shaftGlue residue has built up.Remove the beam and clean the holder with solvent. Use less glue and keep a damp cloth ready for squeeze out. Page 10
Frame does not assemble correctlyThe sides were not joined first, the pairs are unequal, or there is too much glue.Join the sides first, then the halves. Put the longer length in the vise on the right and the shorter on the left. Make sure the pairs are equal length, use less glue and check the saw cuts square. Use longer V-nails if possible. Page 10
Clamped moulding does not fit between the postsThe beam is in the way.Lift the beam off the support rods and place the vise with the moulding between the rods. Reset the beam height and continue. Page 10

Frequently asked questions

What moulding size does the F300-1 accept?

It accepts mouldings up to 2 1/2 inches (64mm). See page 2.

How many V-nails do I need per joint?

Use at least two per joint. Moulding from 1/4 to 1 3/4 inch wide needs 2 nails. Moulding from 2 to 2 1/2 inch wide needs 3. See page 6.

What V-nail size and type should I use?

Choose a nail at least 1/2 the moulding thickness. Hard wood nails are for very hard woods like oak and maple. Soft wood nails are for soft woods and can also be used on hard woods. See page 6.

Can it join plastic mouldings?

Yes. It can join polystyrene and Emafil plastic mouldings. Press the V-nails in slowly but firmly, because they bend if pressed in too fast. See page 8.

How long is the warranty?

The Studio Joiner F300-1 has a one year warranty from the date of original purchase against defects in parts and workmanship. See page 10.