Logan F300-2 Picture Framing Pro Joiner Manual, page 1

Page 1 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 2
Text on page 2

PICTURE FRAMING

The Pro Joiner Model F300-2 has been

designed as a full featured manual joiner

that is easy to use. Features include

alignment pins which will correctly drive

V-nails into all woods, fully adjustable

press for variable moulding sizes and

shapes, adjustable V-nail spacing allowing

you to drive up to two V-nails at once,

convenient V-nail spacing gauge to take

the guess work out of placement, easy to

load V-nail blocks that slide on a fixed rail

and includes a quick set-up clamp to

precisely secure moulding. Precise corner

joints can be achieved with this heavy duty

professional style joiner. Producing

professional quality picture frames is

now easier than ever.

Page 2 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 3
Text on page 3

Identification

Lever Adjustment Block

Lever Height Wheel

V-nail Corner Spacing Stop (Not visible)

V-nail Gauge

V-nail Slide Cartridge

V-nails Moulding Spacer V-nail Slide Cartridge - Allows V-nail blocks to be V-nails - Moulding fasteners. moved out for easy loading. Lever - Arbor press handle used to drive clamped

moulding on to V-nails.

V-nail Blocks - Two blocks which hold V-nails.

Lever Adjustment Block - Block which moves to locate pressure foot and adjust lever height.

V-nail Gauge - Allows for “no guessing” set-up of nail spacing.

Moulding Spacer - Helps in driving awkward profile mouldings onto V-nails.

Vise - Quick set jaw locks moulding in place. Clamp moves up and down to drive wood onto nails.

Pressure Foot - Urethane coated foot which locates on moulding joint and drives wood onto nails.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 3 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 4
Text on page 4

Parts List

Extension Arms

Moulding Spacer

Extension Arm Screws

Extension Arm Wrench

Extension Arm Screws 4

Extension Arm Wrench 1

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 4 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 5
Text on page 5

Assembly Procedure

  1. Align set of holes in arm with holes in vise, making sure the rubber bumper faces up. (Fig. 1).
  2. Attach arm to vise with extension arm screws using extension wrench supplied.

Preparation

  1. Clamp Moulding
  • Mark edges of mitre to blend any gaps in joint (Fig. 2). Use wood stain marker available at hardware store.
  • Glue moulding mitre for long lasting solid corners (Fig. 3).
  • Always start by placing longer length in vise on right hand side and shorter length on left hand side. This will give you two halves of frame, eliminating errors (Fig. 4).
  1. Remove V-nail slider.
  2. Press vise down and tighten vise stop to provide clearance for moulding.
  3. Adjust clamp jaw by pressing spring button and sliding handle (Fig. 5).
  4. Align moulding pieces in vise so top corner is square (Fig. 6).
  5. Tighten handle only as much as necessary to hold joint together.
  6. Release vise stop.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 5 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 6
Text on page 6

Preparation continued

B. Set V-nail Spacing

1. Read dimension from vise scale (Fig. 7).

2. Adjust V-nail block in slider to same dimension as vise scale. V-nails are now set approximately 1/4 inch from each end of joint (Fig. 8).

3. Replace slider. V-nail Corner Spacing Stop

  • Locate slider against the stop by pushing it back as far as it will go.
  • This stop changes the distance the top V-nail is located from the end of the joint (Dimension X) (Fig. 9).

Using 1/2 inch or smaller moulding

  • Only one V-nail block is moveable and it is designed to be removed from the slider.
  • When small mouldings need to be joined. Simply remove the stop knob from end of slider and slide V-nail block out. It cannot be left in slider or damage may occur.
  • This now allows you to drive two V-nails (one at a time in different places) to have a secure joint.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 6 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 7
Text on page 7

Preparation continued

C. Set Pressure Foot Over Moulding

1. Loosen lever adjustment block handle.

2. Adjust lever adjustment block so pressure foot locates over middle moulding or where even downward pressure can be applied (Fig. 10).

3. Tighten lever.

4. Due to the many moulding profiles we have included a black moulding spacer. This is especially useful when the outside edge of moulding is considerably thinner than inside (rabbet) edge of moulding. This should help eliminate the joint from opening (Fig. 11) One nail - the foot should be directly over the nail. Two nails - the foot should be between the nails.

D. Adjust Foot Height

1. With moulding now securely clamped, push the vise down until moulding bottoms out onto V-nail blocks and tighten vise stop.

2. Lower lever handle below horizontal.

3. Adjust pressure foot by turning wheel until it contacts moulding and handle is below horizontal (Fig. 12).

4. Release vise stop.

E. V-nail Type

1. Hardwood nails are used for very hard woods like oak and maple. Do not use these nails on softwoods.

2. Softwood nails are used for other woods but can be used on hardwoods. Test them on hardwoods. If they do not work, use a hardwood nail.

F. V-nail Size

1. As a general rule, nail should be at least 1/2 of moulding thickness.

G. V-nail Quantity

1. 2 V-nails - from 0” to 2” (5cm) 3 V-nails - from 2” (5cm) to 3” (7cm)

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 7 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 8
Text on page 8

Operation

A. Load V-nails

1. Remove slider from base board (Fig. 13).

2. Decide to drive one or two V-nails. With some hardwoods (walnut, etc) it may be easier to press only one V-nail in at a time.

3. Insert V-nail with sharp edge up onto pins oriented the same as the sticker on the V-nail blocks (Fig. 14).

4. Replace slider between guides on baseboard up against corner stop (Fig. 15). For information on how to purchase additional V-nails see page 10.

B. Press Nails

1. Lower lever and pressure foot onto moulding.

2. Press lever completely until vise clamp bottoms on V-nail blocks (Fig. 16). Making a quick firm pull on the lever drives the V-nails faster and more accurately.

3. Raise lever.

4. Remove V-nail slider.

5. Remove jointed moulding corner.

6. Repeat process of clamping a new corner of moulding and loading V-nails.

C. Stacking V-Nails It is possible to drive V-Nails directly behind the first V-Nail (stacking).

This is to make possible, solid corners in extra thick moulding 1 1/2" or more. Care should be taken and it is advisable to practice with scrap moulding first.

  1. To start this procedure, press one V-Nail at a time.
  2. Without moving the V-Nail block from its position in the V-Nail slider, place another V-Nail on the block and replace the slider to its original position.
  3. Press the V-Nail in using slow but firm action.

Note: With some very hard woods, it may be necessary to place the second V-Nail on the V-Nail block upside down. This is to ensure maximum contact with the first V-Nail and the second one being pushed in underneath the first. It may also not be possible to drive it all the way flush with the moulding, depending on wood used, in which case, it may be necessary to sand or file the V-Nail until it is flush with moulding. This should not be done until all 4 corners have been joined.

  1. Repeat the process until the corner has been completely joined and then repeat with the remaining three corners.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 8 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 9
Text on page 9

Trouble Shooting

Make sure the two pairs are equal length.

Reduce the amount of glue in joint.

Check square cutting action of saw.

Use longer V-nails if possible.

V-nails don’t drive in all the way in.

Try using one (1) V-nail at a time, especially when joining hard woods.

Remove any obstruction under vise.

Re-adjust the depth of the lever arm.

V-nail holders won’t emerge from V-nail blocks. Soak in solvent to clear away glue or dust. Place a finger under V-nail block between block and slider to push V-nail holder up.

Moulding joints open up when pressing V-nails in.

Re-adjust the placement of the pressure foot to spread the load more evenly.

Use one V-nail at a time when foot contacts awkward sloping profile moulding.

Warranty

Logan Graphic Products, Inc. (“Logan”) warrants the Pro Joiner - Model F300-2, to be free from defects in parts and workmanship for a period of one year from the date of original purchase. Logan warrants that it will either repair or replace, at it’s sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 9 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 10
Text on page 10

PRO Joiner

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 10 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 11
Text on page 11

PRO Joiner

V-nail Slider

L860NS

Slide Block Tension Screw

Slide Block Spring Pin

Slide Block Spring Pin

Pressure Pad Assembly

Adj. Nut Retaining Ring

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 11 of 12

Logan F300-2 Picture Framing Pro Joiner Manual, page 12
Text on page 12

PRO Joiner

Also ava ilableFromLoganGraphics

Logan Graphics picture framing system includes all the tools and accessories you need to produce professional quality frames including…

Precision Sander ELITE

Model F200-2 Sands miters to perfect 45° angle for tight, square frames

10 lb wheel Adjusts 45° left, 90° and 45° right Micro adjustment for perfect 45° Aluminum oxide sand paper with life extending bar Sand up to 2 1/2“ (64mm) mouldings Dust removal bar

Fittingtool Model F400-1

Drives brads or point inserts into wood frames to hold materials in place

replacement V-Nails Find replacement V-nails where you purchased your tool.

Drives four different inserts No slipping or bending Removes inserts Easy adjust foot Use on hard or soft woods Patented rotating insert holder Proper drive angle assured No guessing or skill required

1/4” (7mm), 3/8” (10mm) and 1/2 (12mm)

sizes are available for both soft and hard wood

applications, packaged in quantities of 200.

dual drive ELITE

Model F500-2

Spring-loaded action drives both rigid and flexible points to secure artwork in both hard and softwood frames

Holds stacks of flexible or rigid points for fast productive framing Comfortable handle grip and smooth firing action Must-have for artists, framers and hobbyists! For best results, using only authentic Logan points

For more information, including where to buy Logan Framing

Products, Please visit us at www.logangraphic.com or

call Toll Free (800) 331 6232.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com

Page 12 of 12 ยท End of manual

Quick start

  1. Attach the extension arms to the vise with the supplied screws and wrench, rubber bumper facing up.
  2. Mark and glue the miters, then clamp the longer piece on the right and the shorter on the left, with the top corner square.
  3. Read the vise scale and set the V-nail block in the slider to the same dimension.
  4. Position the pressure foot over the middle of the moulding, then set the foot height so it touches the moulding with the handle below horizontal.
  5. Load V-nails sharp edge up on the pins and slide the slider back against the corner stop.
  6. Lower the lever and pull it fully with a quick, firm action until the clamp bottoms on the V-nail blocks, then remove the joined corner.

Troubleshooting

ProblemLikely causeFix (from the manual)
Gaps in the jointUnequal lengths, too much glue, or saw not cutting square.Make sure both pairs are equal length, reduce glue, check the saw's square cut, and use longer V-nails if possible. Page 9
V-nails don't drive in all the wayHard wood, an obstruction under the vise, or lever depth set wrong.Drive one V-nail at a time, remove obstructions under the vise, and re-adjust the lever arm depth. Page 9
V-nail holders won't come up from the V-nail blocksGlue or dust build-up.Soak in solvent and push the holder up with a finger between the block and slider. Page 9
Moulding joints open when pressing V-nailsUneven load from the pressure foot.Re-position the pressure foot to spread the load, and use one V-nail at a time on sloping profiles. Page 9

Frequently asked questions

Which V-nails should I use?

Use hardwood nails for very hard woods like oak and maple (not on softwoods); softwood nails work on other woods. The nail should be at least half the moulding thickness. See page 7.

How many V-nails per corner?

Two V-nails for mouldings up to 2" (5 cm) and three from 2" to 3". See page 7.

Can I join mouldings 1/2 inch or smaller?

Yes. Remove the stop knob and slide out the moveable V-nail block, then drive two V-nails one at a time. See page 6.

How do I join extra-thick moulding?

For mouldings 1 1/2" or more you can stack V-nails behind the first, pressing one at a time with slow firm action. Practice on scrap first. See page 8.

What is the warranty?

One year from the date of original purchase against defects in parts and workmanship. See page 9.