Logan F400-1 Picture Framing Fitting Tool Manual, page 1

Page 1 of 3

Logan F400-1 Picture Framing Fitting Tool Manual, page 2
Text on page 2

Model F400-1

Instruction Manual

PICTURE FRAMING

FITTING TOOL

U.S. Patent No. 6,896,168

The Model F400-1 Fitting Tool has been designed to provide long lasting quality operation with easy to use features. It’s primary purpose is to drive pins, points and nails into wood picture frame moulding to securely hold framing materials in place. The Model F400-1 Fitting Tool features a unique and revolutionary rotating turret to accommodate all of the most popular style points.

Operation

A. Driving Insert

1. Slide foot away from turret.

2. Load insert into turret slot. Be sure point end faces out (Fig. 5).

3. Align body and tip of insert against frame. Rest body on framing material. Slide foot until bumper rests firmly against frame (Fig. 6).

Reference Part No. L988

Identification

Lever - Moveable handle which drive inserts. Foot - Sliding stop block. Lock Plate - Locks foot secure. Turret - Insert holder which rotates. Holds four insert styles. Flexible Insert - Bendable insert used to hold framing material inside frame.

  1. Firmly squeeze handle and drive insert into the wood until turret stops against frame (Fig. 7). Note-for best results keep body flat on material while squeezing.
  2. Squeeze lock plate on foot and rotate foot to release (Fig. 8).
  3. Slide body back along top of framing material to remove from insert. Do not lift up, but rather pull straight back.
  4. Repeat to finish.

Preparation

A. Fill frame

1. Turn over frame.

2. Load glass, matboard and image and backing material into frame (Fig. 1).

B. Choose an insert (Fig. 2).

1. Flexible Insert- Bendable insert used in photo frames where material can easily be changed. Brad Nails - Economical insert. Can be used for securing canvas. Multipoint Insert - Bendable insert and used to hold fillets in place. Rigid Insert - Firm insert used in permanent applications.

Problem: Points bend when being inserted.

Backing Material (Foamboard or Cardboard)

Solution: Try using a different insert more suited to hardwood.

Problem: Mats or framed material buckles after being secured.

Solution: Let the turret rest gently on back of material when inserting points. Do not angle inserts down to “pinch” material being secured.

Problem: Fitting Tool handle does not release after point insertion.

Solution: Release pressure by squeezing lock plate on the foot and swivel foot to clear moulding, then withdraw turret in opposite direction of insertion.

continued on next page

Flexible Insert

Brad Nail

Multipoint Insert

Rigid Insert

Preparation continued

B. Choose an insert (continued)

2. Rotate turret so insert choice faces foot (Fig. 3).

C. Determine insert spacing and quantity

1. Corner spacing is generally 1” (3cm) to 2” (5cm) from corner.

2. Side spacing is generally 4” (10cm) to 5” (13cm) apart (Fig. 4).

Warranty

Make sure the turret is resting flush on back material being framed.

Trouble Shooting

Model F400-1

FITTING TOOL

Instruction Manual

Logan Graphic Products, Inc. (“Logan”) warrants the Fitting Tool - Model F400-1, to be free from defects in parts and workmanship for a period of one year from the date of original purchase. Logan warrants that it will either repair or replace, at it’s sole discretion, any necessary replacement parts found to be defective. Should the product need to be returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This warranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other warranties, expressed or implied.

No. L811 L963 L964-N L965 L966 L967 L968 L969 L970 L972 L975 L976 L977 L978

Description Lock Plate Spring Bumper End Cap Handle Body Turret-Top Turret-Bottom Lock Plate Foot Drive Rod Turret Screw Pivot Screw Ball Ball Spring

Logan Graphic Products, Inc. 1100 Brown Street, Wauconda, IL 60084 USA Phone 1 847 526 5515 Toll Free 1 800 331 6232 www.logangraphic.com

Reference Part No. L988

Page 2 of 3

Logan F400-1 Picture Framing Fitting Tool Manual, page 3
Text on page 3

Bedienungsanleitung

Mode d'emploi

Modèle F400-1/ Modelo F400-1/ Modell F400-1/Modello F400-1

BILDEINRAHMUNG

ENCADREMENT

FR OUTIL D’AJUSTAGE

Description L’outil d’ajustage modèle F400-1 a été conçu pour assurer un fonctionnement de qualité de longue durée avec des caractéristiques ergonomiques. Sa fonction principale est de chasser des taquets, des pointes et des clous dans la moulure de cadre de tableau en bois pour tenir fermement en place les matériaux d’encadrement. L’outil d’ajustage modèle F400-1 se caractérise par une tourelle rotative révolutionnaire qui accepte toutes les pointes les plus populaires.

EINSTIFTGERÄT

Beschreibung Das Einstiftgerät F400-1 ist ein leicht zu handhabendes Werkzeug von langer Lebensdauer, mit dessen Hilfe sich verschiedene Stifttypen wie Points, Pfeile und Nägel einfach in Bilderrahmen einstiften lassen, so dass das jeweilige Einrahmobjekt fest und sicher gehalten wird. Das Gerät F400-1 verfügt über ein einzigartiges und revolutionäres drehbares Stiftemagazin, in welches die unter Einrahmern populärsten Stifttypen passen.

U.S. Patent No. 6,896,168

Manuale d’uso

Manual De Instrucción

ENMARCADO DE CUADROS

PER INCORNICIATURA

ESP HERRAMIENTA DE ACOPLE

ITL UTENSILE DI MONTAGGIO

Descripción La Herramienta de Acople Modelo F400-1 ha sido diseñada para proveer una operación de calidad y duradera con propiedades ventajosas fáciles de usar. Su propósito primario es introducir grapas, puntas y clavos en la moldura de madera del marco para retener con seguridad los materiales del enmarcado en su lugar. La Herramienta de Acople Modelo F400-1 ofrece una torreta rotatoria única y revolucionaria para utilizar con todos los estilos más populares de puntas.

Descrizione L’Utensile di montaggio modello F400-1 è stato progettato per un funzionamento durevole e di qualità e per essere semplice da utilizzare. Il suo scopo consiste nell’inserire perni, punte e chiodi in cornici di legno al fine di tenere saldamente in posizione i materiali di incorniciatura. L’Utensile di montaggio modello F400-1 è dotato di un’esclusiva e rivoluzionaria torretta rotante per accogliere le punte di tutti i tipi.

Identification Identificación Bezeichnung Identificazione

Plaque de verrou Placa Aseguradora Arretierungsplatte Piastra di bloccaggio

Sabot Pie Fuß Piede

Levier Palanca Hebel Leva

Butée Apoyo Puffer Paraurti

Tourelle Torreta Stiftemagazin Torretta

ESP

ITL

Palanca - Manija movible que empuja las puntas. Pie - Bloque deslizante de apoyo. Placa Aseguradora – Traba el pie asegurándolo. Torreta - Portador de puntas rotatorio. Sostiene cuatro estilos de puntas. Punta flexible - Punta flexible usada para sostener los materiales de enmarcado dentro del marco.

Leva – Manico mobile per inserire i tasselli. Piede – Blocchetto di arresto scorrevole. Piastra di bloccaggio – Blocca stabilmente il piede. Torretta – Portatasselli rotante. Idoneo per quattro tipi di tasselli. Tassello flessibile – Tassello pieghevole utilizzato per tenere fermo nella cornice il materiale di incorniciatura.

FR

ESP

Preparazione Preparación Vorbereitung A . Introduzcaelmarco A . B e f ü llendesRahmens A . Riempirelacornice

1. Voltee completamente

1. Drehen Sie den

1. Capovolgere la cornice el marco. Rahmen um.

2. Inserire il vetro, il car-

2. Cargue el vidrio, la

2. Legen Sie das Glas, tone pesante, la lámina perimétrica e den Passepartoutkarton fotografia e il imagen y el material und das Objekt mit materiale di rinforzo del forro dentro del dem Rückwandkarton nella cornice (Fig. 1). B . Selezionareun marco (Fig. 1). in den Rahmen (Abb. 1) B . Elijaunapunta (Fig. 2) B . Auswahleines tassello (Fig. 2). Stifttyps (Abb. 2).

1. Punta Flexible- Punta

1. Tassello flessibile –

1. Flexipoint: Biegbarer flexible usada en los Tassello pieghevole Stift für Fotorahmen, marcos de fotos donde utilizzato in cornici per schnelles el material se puede foto in cui il materiale Auswechseln des cambiar fácilmente. possa essere cambia- Einrahmobjekts Clavos Brad sin to facilmente. möglich cabeza – Punta de Chiodo senza testa – Nagel: retención de bajo pre- Tassello economico. Kostengünstiger Stift, cio. Può essere utilizzato kann zum Fixieren von Pueden ser utilizadas per fissare la tela. Leinwand verwendet para asegurar lienzos Tassello multipunto – werden de lona. Tassello pieghevole Mehrfachpoint:

Grapa de múltiples utilizzato per man- Biegbarer Stift zum puntas - Grapa flexible tenere in posizione i Fixieren von Inlays y utilizada para nastri. Pfeil: Fester Stift für sostener filetes en su Tassello rigido – permanente lugar. Tassello fisso utilizzato Anwendungen Punta rígida - Punta per applicazioni perfirme empleada para manenti. Fortsetzung nächste Seite usos permanentes. continua alla pagina succontinúa en la página cessiva siguiente

suite à la page suivante

FR

ESP

Préparation (suite) B . S é lectionneruninsert (suite).

  1. Faire pivoter la tourelle pour que l’insert choisi soit face au sabot (Fig. 3).

C . D é terminerl ’ espacementet laquantit é d ’ inserts .

  1. En règle générale, espacer les inserts de 25,5 mm (1 po) à 51 mm (2 po) des coins.
  2. Espacer latéralement les inserts les uns des autres de 101,5 mm (4 po) à 127 mm (5 po) (Fig. 4).

Preparación (continuación) B . Elijaunapunta (continuación)

  1. Rote la torreta de modo que la punta elegida dé frente al pie (Fig. 3).

C . Determineelespaciamien toylacantidaddepuntas

  1. El espaciamiento de la esquina es generalmente de 1" (2.5cm) a 2" (5cm) desde la esquina.
  2. El espaciamiento lateral es generalmente 4" (10cm) a 5" (13cm) de separación (Fig. 4).

Hebel: Hebelgriff zum Einstiften. Fuß: Verschiebbarer Anschlagsblock. Arretierungsplatte: Arretiert den Fuß an einer bestimmten Position. Stiftemagazin: Drehbar, passend für vier verschiedene Stifttypen. Flexipoint: Verbiegbarer Stift zum Fixieren des Einrahmobjekts im Rahmen.

Levier – poignée mobile qui chasse les inserts. Sabot – bloc de butée coulissant Plaque de verrou – verrouille fermement le sabot. Tourelle – porte-insert rotatif. Porte quatre types d’inserts. Insert flexible – insert pliable utilisé pour maintenir l’objet à encadrer à l’intérieur du cadre.

Préparation A . Remplirlecadre

  1. Retourner le cadre.
  2. Charger le verre, le passe-partout et l’image et le matériau de support dans le cadre (Fig. 1).

B . S é lectionneruninsert (Fig. 2).

  1. Insert flexible – insert pliable utilisé dans les cadres de photo où le matériau peut être facilement remplacé.

Clous de vitrier – insert économique. Peuvent être utilisés pour fixer des toiles. Insert multipoint – insert pliable utilisé pour tenir des listels en place. Insert rigide – insert ferme utilisé dans des applications permanentes.

FR

ITL

Vorbereitung (Fortsetzung) B . AuswahleinesStifttyps (Fortsetzung)

2. Drehen Sie das Stiftemagazin so, dass der Stifttyp in Richtung Fuß zeigt. (Abb. 3) C . BestimmendesAbstands undderAnzahlderzu verwendendenStifte

1. Die Stifte werden gewöhnlich etwa 5 cm von den Ecken entfernt gesetzt.

2. Der Abstand zwischen den einzelnen Stiften beträgt gewöhnlich etwa 10 bis 13 cm (Abb. 4).

Insert Punta Stift Tassello

Moulure Moldura Leiste Cornice

Verre Vidrio Glas Vetro

FR

ESP

Fonctionnement A . Chassedesinserts

  1. Faire glisser le sabot à l’écart de la tourelle.
  2. Charger l’insert dans la fente de la tourelle. S’assurer que l’extrémité pointue est orientée vers l’extérieur (Fig. 5).
  3. Aligner le corps et l’extrémité de l’insert contre le cadre. Faire reposer le corps sur le matériau d’encadrement. Faire glisser le sabot jusqu’à ce que la butée s’appuie fermement contre le cadre (Fig. 6). suite à la page suivante

Operación A . Introducci ó ndelapunta

  1. Deslice el pie lejos de la torreta.
  2. Cargue la punta en la rendija de la torreta. Asegúrese que el extremo de la punta apunte hacia afuera (Fig. 5)
  3. Alinee el cuerpo y los extremos de la punta en el marco. Descanse el cuerpo sobre el material enmarcado. Deslice el pie hasta que el apoyo descanse firmemente contra el marco (Fig. 6). continúa en la página siguiente

FR

Preparazione (continuo) B . Selezionareuntassello (continuo).

  1. Ruotare la torretta così che il tassello scelto sia rivolto verso il piede (Fig. 3).

C . Stabilireladistanzaela quantit à deltassello .

  1. Di norma, la distanza angolare è compresa tra 1" (3 cm) e 2": (5 cm) dall’angolo.
  2. Di norma, la distanza laterale è compresa tra 4" (10 cm) e 5" (13 cm) (Fig. 4).

Insert rigide Punta Rígida Pfeil Tassello rigido

ITL

ITL

FR

ESP

ITL

Problème : Les pointes se tordent quand elles sont insérées. Solution : Essayer d’utiliser un insert différent, mieux adapté au bois dur. S’assurer que la tourelle repose en affleurant sur le matériau de support en cours d’encadrement. Problème : Les caches ou le matériau encadré ondulent après avoir été fixés. Solution : Laisser la tourelle reposer doucement sur l’arrière du matériau lors de l’insertion de pointes. Ne pas incliner les inserts vers le bas pour « pincer » le matériau en cours de fixation. Problème : La poignée de l’outil d’ajustage ne se relâche pas après l’insertion des pointes. Solution : Relâcher la pression en serrant la plaque de verrou sur le sabot, pivoter le sabot pour dégager la moulure puis retirer la tourelle dans la direction opposée de l’insert.

Problema: Las puntas se doblan al ser insertadas Solución: Intente usar una punta diferente que sea más adecuada a la dureza de la madera. Asegúrese de que la torreta está descansando a ras sobre el material que se está enmarcando. Problema: Las láminas periféricas o el material enmarcado se comban después de ser asegurados. Solución: Deje que la torreta descanse suavemente encima del material al insertar las puntas. No deje que las puntas entren en ángulo "mordiendo" el material que se está asegurando. Problema: La manija de la herramienta de acople no libera después de la inserción de la punta. Solución: Libere la presión apretando la placa aseguradora del pie y rote el pie para soltar la moldura, entonces retire la torreta en la dirección opuesta a la de la inserción.

Problem: Der Stift verbiegt sich beim Einstiften. Lösung: Verwenden Sie einen anderen Stifttyp, der besser für Hartholz geeignet ist. Stellen Sie sicher, dass das Stiftemagazin flach auf dem Einrahmobjekt aufliegt. Problem: Passepartoutkarton oder Einrahmobjekt wellen sich nach dem Einstiften. Lösung: Das Stiftemagazin muß beim Einstiften flach auf dem Einrahmobjekt aufliegen. Vermeiden Sie es, das Werkzeug in einem anderen Winkel anzulegen, und den Stift nach unten in die Leiste „einzustechen". Problem: Der Hebelgriff des Werkzeugs löst sich nach dem Einstiften nicht. Lösung: Verringern Sie den Druck, indem Sie zuerst die Arretierungsplatte lösen und den Fuß von der Leiste wegschieben. Ziehen Sie nun das Werkzeug mit dem Stiftemagazin in entgegengesetzter Richtung vom Stift weg.

Problema: Le punte si piegano quando vengono inserite. Soluzione: Tentare di utilizzare un tassello diverso che risulti più adatto legno duro. Accertarsi che la torretta sia appoggiata a filo sul materiale di rinforzo da incorniciare. Problema: Il cartone pesante o il materiale incorniciato si curva dopo essere stato fissato. Soluzione: Quando si inseriscono le punte, lasciare che la torretta si appoggi dolcemente sul retro del materiale. Non curvare i tasselli verso il basso per "pinzare" il materiale che si sta fissando. Problema: Il manico dell’utensile di montaggio non rilascia le punte dopo averle inserite. Soluzione: Rilasciare pressione stringendo la piastra di bloccaggio sul piede e ruotare il piede per liberare la cornice, quindi ritirare la torretta in direzione opposta all’inserimento.

FR

Problèmes et solutions • Solución de Fallas • Problembehebung • Localizzazione guasti

Matériau de support (en mousse ou en carton) Material del Forro (Lámina de espuma o Cartulina) Rückwandkarton (Hartschaumplatte oder Karton) Materiale di rinforzo (Pannello in espanso o di cartone)

Insert multipoint Grapa de múltiples puntas Mehrfachpoint Tassello multipunto

ESP

ITL

Funzionamento A . Inserimentodeltassello

  1. Far scorrere il piede lontano dalla torretta.
  2. Inserire il tassello nella scanalatura della torretta. Accertarsi che l’estremità appuntita sia rivolta verso l’esterno (Fig. 5).
  3. Allineare corpo e punta del tassello contro la cornice. Appoggiare il corpo sul materiale di incorniciatura. Far scorrere il piede finché il paraurti non poggi stabilmente contro la cornice (Fig. 6). continua alla pagina successiva

Funzionamento (continuo) Bedienung (Fortsetzung) Operación (continuación) Fonctionnement (suite) A . Chassedesinserts (suite) A . Introducci ó ndelaPunta A . Einstiften (Fortsetzung) A . Inserimentodeltassello

4. Serrer fermement la

4. Drücken Sie den Hebelgriff (continuación) (continuo) poignée et chasser l’insert fest zusammen, und treiben

4. Apriete firmemente la mani-

4. Stringere saldamente il dans le bois jusqu'à ce que Sie den Stift soweit in den ja y empuje la punta dentro manico e inserire il tassello la tourelle s’arrête contre le Rahmen, bis das de la madera hasta que la nel legno finché la torretta cadre (Fig. 7). Stiftemagazin an der Leiste torreta se detenga contra el non si fermi contro la Remarque : pour de anschlägt. (Abb. 7) marco (Fig. 7) cornice (Fig. 7). meilleurs résultats, main- Anmerkung: Das Gerät Nota – Para mejores resul- Nota – Per ottenere migliori tenir le corps à plat contre sollte dabei flach auf dem tados mantenga el cuerpo risultati, tenere il corpo le matériau tout en serrant. Einrahmmaterial aufliegen plano sobre el material piano sul materiale mentre

5. Serrer la plaque de verrou

5. Drücken Sie nun auf die mientras aprieta. si esercita pressione. contre le sabot et faire piv- Arretierungsplatte des

5. Apriete la placa asegurado-

5. Stringere la piastra di oter celui-ci pour le libérer Fußes und drehen Sie ra sobre el pie y rote el pie bloccaggio sul piede e (Fig. 8). diesen, um ihn zu lockern. para soltar (Fig. 8). ruotare il piede per

6. Faire coulisser le corps en (Abb. 8)

6. Deslice el cuerpo hacia rilasciare (Fig. 8). arrière le long de l’arête

6. Ziehen Sie nun das atrás encima del material

6. Far scorrere il corpo indisupérieure du matériau Werkzeug nach hinten vom de enmarcado para retiraretro lungo la parte superid’encadrement pour le Stift weg. lo de la punta. ore del materiale di incornidétacher de l'insert.

7. Wiederholen Sie diese

7. Repita hasta terminar. ciatura per rimuoverlo dal

7. Recommencer pour com- Schritte, bis der Rahmen tassello. pléter l’opération. fertig ist.

7. Ripetere l’operazione fino a risultato ottenuto.

Passe-partout ou image Lámina perimétrica o imagen Passepartoutkarton oder Objekt Cartone pesante o fotografia

Clou de vitrier Insert flexible Clavo Brad sin cabeza Punta flexible Nagel Flexipoint Chiodo senza testa Tassello flessibile

Bedienung A . Einstiften

  1. Drücken Sie auf die Arretierungsplatte und schieben Sie den Fuß vom Stiftemagazin weg.
  2. Schieben Sie den Stift in den entsprechenden Schlitz des Stiftemagazins. Stellen Sie sicher, dass die Spitze des Stifts aus dem Schlitz herausschaut. (Abb. 5)
  3. Legen Sie das Einstiftgerät mit der Spitze des Stifts nach vorn gerichtet so von innen an der Leiste an, dass es gleichzeitig auf dem Einrahmobjekt aufliegt. Schieben Sie den Fuß nun soweit an die Leiste, dass der Puffer fest an ihr anliegt. (Abb. 6) Fortsetzung nächste Seite

Description Ressort de plaque de verrou Butée Capuchon Poignée Corps Tourelle – sommet Tourelle – base Plaque de verrou Sabot Biellette d’entraînement Vis de tourelle Vis pivot Rotule Ressort de rotule

Nr. Beschreibung L811 Arretierungsplattenfeder L963 Anschlag L964-N Stangenkappe L965 Hebelgriff L966 Werkzeugkörper L967 Oberteil Stiftemagazin L968 Unterteil Stiftemagazin L969 Arretierungsplatte L970 Fuß L972 Schubstange L975 Magazinschraube L976 Drehschraube L977 Kugel L978 Kugelfeder

Rev. 7/08

ESP No

L811

ITL

Descripción Resorte de la Placa Aseguradora Apoyo Casquillo del Extremo Manija Cuerpo Parte Alta de la Torreta Parte Baja de la Torreta Placa Aseguradora Pie Varilla Impulsora Tornillo de la Torreta Tornillo Pivote Bola Resorte de la Bola

Descrizione Molla piastra di bloccaggio Paraurti Cappuccio di estremità Manico Corpo Parte superiore torretta Parte inferiore torretta Piastra di bloccaggio Piede Asta di trascinamento Vite torretta Vite perno Sfera Molla sfera

Logan Graphic Products, Inc. 1100 Brown Street, Wauconda, IL 60084 USA Phone 1 847 526 5515 Toll Free 1 800 331 6232 www.logangraphic.com

Numéro de référence L988 • Pieza de Referencia No. L988 • Referenz-Teilenr L988 • N. pezzo di riferimento L988

Page 3 of 3 ยท End of manual

Quick start

  1. Turn the frame over and load the glass, matboard, image and backing material.
  2. Choose an insert (flexible, brad nail, multipoint or rigid) and rotate the turret so it faces the foot.
  3. Slide the foot away from the turret and load the insert with the point end facing out.
  4. Rest the body on the framing material and slide the foot until the bumper rests firmly against the frame.
  5. Squeeze the handle firmly until the turret stops against the frame, keeping the body flat.
  6. Squeeze the lock plate, rotate the foot to release, and pull the tool straight back. Space points 1"-2" from corners and 4"-5" apart.

Troubleshooting

ProblemLikely causeFix (from the manual)
Points bend when being insertedThe insert is not suited to the wood (e.g. hardwood).Try a different insert more suited to hardwood. Page 2
Mats or framed material buckle after securingInserts angled down, pinching the material.Let the turret rest gently and flush on the back material; do not angle the inserts down. Page 2
Handle does not release after insertionPressure still held by the foot.Squeeze the lock plate on the foot, swivel the foot clear of the moulding, then withdraw the turret opposite to the insertion direction. Page 2

Frequently asked questions

Which insert should I use?

Flexible inserts for photo frames where contents change, brad nails as an economical option (also for canvas), multipoint inserts to hold fillets, and rigid inserts for permanent framing. See page 2.

How far apart should points be spaced?

Generally 1" (3 cm) to 2" (5 cm) from each corner and 4" (10 cm) to 5" (13 cm) apart along the sides. See page 2.

What is the warranty?

One year from the date of original purchase against defects in parts and workmanship. See page 2.