Logan F500-2 Picture Framing Dual Drive Elite Manual, page 1

Page 1 of 3

Logan F500-2 Picture Framing Dual Drive Elite Manual, page 2
Text on page 2

Model F500-2

Instruction Sheet

PICTURE F RAMING

Dual DrivE Elite Point Driver

Operation

  1. Hold outside of frame
  2. Press driver nose against inside frame
  3. Keep drive flat on material - DO NOT LIFT OR ANGLE
  4. Squeeze trigger to insert point
  5. Space points 6” apart, 3” from corners

Point Loading Cover

Adjust Point Depth Increase drive tension for hardwoods and decrease for softwoods.

Replacement Points Use only Logan Points F53 - Flex (600) F54 - Rigid (600) F55 - Flex (2500) F56 - Rigid (2500)

Loading Points

  1. Press release button
  2. Pull up cover
  3. Install point strips with point facing forward
  4. Slide cover closed

Point Jammed

  1. Remove points
  2. Remove nose screw and nut
  3. Remove nose piece and discard jammed point

See the entire line of Logan DIY Picture Framing Tools and Mat Cutting Equipment at www.logangraphic.com or call 1-800-331-6232 for more information.

Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084

Page 2 of 3

Logan F500-2 Picture Framing Dual Drive Elite Manual, page 3
Text on page 3

Dual Drive Elite Agrafeuse Dual Drive Elite Point Driver Dual Drive Elite Point Driver

Feuille d’instructions Gebrauchsanweisung Hoja de Instrucciones

Ajustement de Profondeur Augmentez la force de frappe pour les bois durs et diminuez la force de frappe pour les bois tendres. (2)

Einstellung der Einschusstiefe Für harte Hölzer Druck erhöhen, für weiche Hölzer Druck verringern. (2)

Ajuste de Profundidad Aumentar la presión para maderas duras y disminuir la presión para maderas blandas. (2)

Chargement de pointes (3)

  1. Appuyez sur le bouton pour libérer le magasin de pointes
  2. Soulevez le couvercle du magasin
  3. Rechargez les pointes

Fonctionnement (4)

  1. Maintenez le cadre exterieur
  2. Placez la tête de l’agrafeuse contre la partie intérieure du cadre
  3. Maintenez l’outil bien à plat sur le matériau. Ne le levez pas ni ne l’inclinez
  4. Appuyez sur la gâchette pour insérrer les pointes
  5. Espacez de 15 cm les pointes entre elles et commencez à 7cm des angles

Remplacement des pointes Utilisez uniquement les pointes Logan F53 Flex (100) F54 Rigides (100) F55 Flex (100) F56 Rigides (2.500)

Deblocage de l’agrafeuse (5)

  1. Retirez les pointes
  2. Retirez la vis et l’ecrou du magasin
  3. Sortez le magasin et enlevez la pointe coincée

Consultez toute la ligne Logan sur les outils d’encadrement de photos et équipements de découpe de passe-partouts sur www.logangraphic.com

Nachfüllen von Stiften (3)

  1. Magazinlösungsknopf betätigen
  2. Stiftemagazin-Deckel hochziehen
  3. Stifte einlegen

Funktionsweise (4)

  1. Rahmen festhalten
  2. Ansetzer von innen gegen den Rahmen drücken
  3. Werkzeug flach auf dem Material halten, NICHT ANHEBEN ODER ANWINKELN
  4. Auslöser betätigen um den Stift einzuschiessen
  5. Empfohlener Abstand zwischen Stiften 15 cm, Abstand zur Rahmenecke: 7 cm

Ersatzstifte Nur original Logan Stifte verwenden F53 Flex (100) F54 Fest (100) F55 Flex (2500) F56 Fest (2.500)

Entfernen steckengebliebener Stifte (5)

  1. Stifte aus dem Magazin entfernen
  2. Anschlagschraube und Mutter lösen
  3. Anschlag entfernen und steckengebliebenen Stift entnehmen.

Erfahren Sie mehr über Logans DIY Einrahmwerkzeuge und Passepartoutschneidgeräte unter www.logangraphic.com

Recargar grapas (3)

  1. Empujar botón de apertura del cargador
  2. Levantar tapa del cargador de grapas
  3. Recargar las grapas.

Funcionamiento (4)

  1. Mantener marco fijo
  2. Poner el posicionador contra la parte interior del marco
  3. Mantener la herramienta en posición plana, NO LEVANTAR O INCLINAR
  4. Utilizar disparador para meter las grapas
  5. Distancia recomendada entre las grapas: 15 cm, desde la esquina del marco: 7 cm Grapas de recambio:

Sólo utilizar grapas originales de Logan F53 Flex (100) F54 Rígidas (100) F55 Flex (100) F56 Rígidas (2.500)

Desatascar la grapadora (5)

  1. Extraer las grapas del cargador
  2. Soltar tornillo y tuerca del posicionador
  3. Extraer posicionador y eliminar grapa atascada

Para más información sobre las herramientas de enmarcación y cortadoras de passepartout de Logan, consulte www.logangraphic.com

Modèle F500-2 Modell F500-2 Modelo F500-2

1 Bouton d’ouverture du magasin

Magazinlösungsknopf Botón de apertura del cargador

Gâchette Auslöser Disparador

Couvercle du magasin de pointes Stiftemagazin- Deckel Tapa del cargador de grapas

Ajustement de la profondeur Einsteller für Einschusstiefe Ajuste de profundidad

Tête Ansetzer Posicionador

Vis d’ajustement Einstellschraube Tornillo de Ajuste

LoganGraphicProductsInc . , 1 1 00 Brown Street, Wauconda, IL 60084 847-526-5515 www.logangraphic.com

Page 3 of 3 · End of manual

Quick start

  1. Load points: press the release button, pull up the cover, install the point strips with the points facing forward and slide the cover closed.
  2. Hold the outside of the frame and press the driver nose against the inside of the frame.
  3. Keep the driver flat on the material; do not lift or angle it.
  4. Squeeze the trigger to insert a point.
  5. Space points 6" apart and 3" from the corners.

Troubleshooting

ProblemLikely causeFix (from the manual)
Point jammedA point stuck in the nose piece.Remove the points, remove the nose screw and nut, then remove the nose piece and discard the jammed point. Page 2

Frequently asked questions

How do I adjust it for hardwood or softwood?

Increase the drive tension for hardwoods and decrease it for softwoods. See page 2.

Which replacement points does it use?

Logan points only: F53 Flex (600), F54 Rigid (600), F55 Flex (2500) and F56 Rigid (2500). See page 2.

How far apart should I place points?

6" apart and 3" from the corners. See page 2.