Logan F500-3 Deluxe Frame Finishing Kit Manual, page 1

Page 1 of 5

Logan F500-3 Deluxe Frame Finishing Kit Manual, page 2

Page 2 of 5

Logan F500-3 Deluxe Frame Finishing Kit Manual, page 3
Text on page 3

Dual DrivE Elite Point Driver

Operating Instructions

Loading Points

  1. Press release button
  2. Pull up cover
  3. Install point strips with point facing forward NOTE: Make sure points are inserted down into nose piece.
  4. Slide cover closed (Fig. 1)

Operation

1. Hold outside of frame

2. Press driver nose against inside frame

3. Keep drive flat on material - DO NOT LIFT OR ANGLE

4. Squeeze trigger to insert point

5. Space points 6” apart, 3” from corners (Fig. 2)

1. Turn adjustment screw to increase tension for hardwoods or decrease tension for softwoods. (Fig. 3)

Point Jammed

  1. Remove points
  2. Remove nose screw and nut
  3. Remove nose piece and discard jammed point (Fig. 4)

Replacement Points Use only authentic Logan Points F53 - Flex (600) F54 - Rigid (600) F55 - Flex (2500) F56 - Rigid (2500)

IF GUN JAMS & NO LONGER FIRES POINTS

Keep 1” or higher stack of points in gun at all times Make sure you are using authentic Logan rigid or flexible points (F53, F54, F55, F56). Make sure points are loaded and seated correctly. Try removing and re-loading the point strip. To remove a point jammed in the nose piece, reference the instructions to remove the nose piece, clear it and re-install it. If point does not leave the gun, try reducing or tightening tension. Check to see that main body screws holding two halves of the tool together are not loose. If necessary, re-tighten with Phillips screwdriver.

IF THE POINT BENDS

  • If flexible inserts are bending or not staying in the wood, try increasing the tension or switch to rigid points.
  • Try reducing the tension if handle is hard to pull.

Logan Graphic Products Inc. 1100 Brown Street, Wauconda, IL 60084 1-847-526-5515 1-800-331-6232 LoganGraphic.com

Page 3 of 5

Logan F500-3 Deluxe Frame Finishing Kit Manual, page 4
Text on page 4

DUST COVER TRIMMER

Operating Instructions

Left hand usage mount side

Blade install: (Fig. 1)

  1. Determine right hand or left hand usage.
  2. Remove nut and three (3) blades.
  3. Separate and install one blade, sharp edge down.
  4. Slide cover to “safe” when not using and “blade” when ready to use.

Apply dust cover:

  1. Using double sided tape , ATG tape or glue, apply continuous line around back of frame about 1/8” from edge (Fig. 2)

Right hand usage mount side

  1. Cut a piece of Kraft paper (30, 40, or 50 lb available at craft stores) that is larger than overall outside of frame by a minimum of 1”.
  2. Lay paper flat onto table and drop the frame straight down onto the paper with taped side down and artwork side facing up. (Fig. 3)
  3. Using water in a spray bottle, completely dampen Kraft paper evenly. As water dries, the paper will shrink tight. (Fig. 4) NOTE: Use a hairdryer to decrease drying time.
  4. Crease paper along the edges of frames (Fig. 5)
  5. Using trimmer, start beyond edge of a corner, hold on slight angle up against frame edge. Draw trimmer along edge to trim. (Fig. 6)
  6. Repeat for other three sides.

Logan Graphic Products Inc. 1100 Brown Street, Wauconda, IL 60084 1-847-526-5515 1-800-331-6232 www.logangraphic.com

Page 4 of 5

Logan F500-3 Deluxe Frame Finishing Kit Manual, page 5
Text on page 5

Installing Hanging Wire and Bumper Pads

Several options exist for hanging your artwork, but the general method utilizes picture hanging wire because it provides the greatest ease and flexibility with artwork of any size. In recent years, strap hangers with D‑rings have grown in popularity over screweyes, because they lie flat against the back of the dust cover and won’t scratch the wall.

Installing D-Rings

To position D-Rings, measure about one-third down from the top of the frame and mark the location. Do this on both sides. Nylon-coated hanging wire comes in three strengths: 19 lb., 25 lb. and 43 lb. Each strength is a measure of the weight-bearing capacity of the wire. If the framed piece is too heavy for the wire, the wire will unravel, pulling free of the hangers, regardless of the complexity of the knots used.

To attach D-Rings to soft or medium wood frames, make a pilot hole in the back of the frame with a scratch awl. Turn the screw into the wood with a screwdriver (Fig. 1). To attach a D-Ring into hard‑ wood frames, drill a hole with a power drill and attach the screw with a power screwdriver (Fig. 2).

Installing Wire

To install the wire, insert one end through the D-Ring allowing 3-5 inches of wire to feed through, twist it around itself and loop it through the D-Ring one more time. Pull tight and then coil the excess around itself keeping the coil tight and cutting away any excess after finishing. (Fig. 3)

Stretch the wire across through the other D-Ring allowing 3-5 inches of excess, use a finger to pull up slightly in the center of the wire to create some slack in the middle of the wire and repeat the tying and coiling process. (Fig. 4)

Attaching Bumper Pads

For a nice finishing touch, attach self-adhesive bumper pads to bottom corners on the back of your frame. These will prevent the frame from scratching the wall, allow air circulation behind the frame to help prevent any condensation and allow some light behind the frame to help prevent fading of wall paint color. (Fig. 5)

Logan Graphic Products Inc. 1100 Brown Street, Wauconda, IL 60084 1-847-526-5515 1-800-331-6232 www.logangraphic.com N1328 Rev 1 09/15

Page 5 of 5 · End of manual

Quick start

  1. Load the point driver: press the release button, lift the cover, insert point strips facing forward and seated in the nose piece, then close the cover.
  2. Press the nose against the inside of the frame, keep it flat and squeeze the trigger. Space points 6" apart and 3" from corners.
  3. Apply double sided tape, ATG tape or glue around the back of the frame about 1/8" from the edge.
  4. Drop the frame taped side down onto Kraft paper at least 1" larger than the frame, then dampen the paper evenly with a spray bottle so it shrinks tight.
  5. Crease the paper along the frame edges and trim with the dust cover trimmer, starting beyond a corner.
  6. Mark D-ring positions about one-third down from the top on both sides, attach them, and tie on hanging wire leaving 3-5" of excess at each end.

Troubleshooting

ProblemLikely causeFix (from the manual)
Point driver jams and no longer fires pointsLow point stack, non-Logan points, points not seated, or wrong tension.Keep a 1" or higher stack loaded, use authentic Logan F53-F56 points, re-load the strip, clear the nose piece, adjust tension, and tighten loose body screws. Page 3
Point is jammed in the nose pieceA point stuck in the nose.Remove the points, remove the nose screw and nut, then the nose piece, and discard the jammed point. Page 3
Flexible points bend or don't stay in the woodTension too low for the wood.Increase the tension or switch to rigid points. Page 3
Handle is hard to pullTension set too high.Reduce the tension. Page 3

Frequently asked questions

How do I adjust the driver for hardwoods?

Turn the adjustment screw to increase tension for hardwoods or decrease it for softwoods. See page 3.

What paper should I use for the dust cover?

Kraft paper (30, 40 or 50 lb) cut at least 1" larger than the outside of the frame. See page 4.

Where should D-rings go?

About one-third down from the top of the frame on both sides. See page 5.

What hanging wire strengths are there?

Nylon-coated wire comes in 19 lb, 25 lb and 43 lb strengths; wire that is too weak for the piece can unravel. See page 5.