

Page 1 of 8

Text on page 2
Height range: 640-1290 mm / 25.2 x 50.8 in Weight capacity: 120 kg / 256 lbs Features: Electric, triple stage, dual motor, T-frame configuration, two memory position handset + home, expandable frame Notes: Desktop sold separately, images may vary from purchased desk
Electric / Triple Stage / Dual Motor
Page 2 of 8

Text on page 3
HANDSET
MANUAL RESET:
Check to make sure all cables are well connected, retry handset. If issue continues... Disconnect power cable for 3 minutes, reconnect power cable, retry handset.
Auto saved memory position (will go to 720mm)
Second memory position (press and hold 5 seconds to save)
First memory position (press and hold 5 seconds to save)
Display screen (640mm - 1290mm)
Down key (push and hold)
Up key (push and hold)
CAUTION
Keep children away from desk - especially handset, controller / powerbrick, legs, or cables. There is a risk of electric shock or serious injury.
Do not open any componements - especially handset, controller / powerbrick, legs or cables. There is a risk of electric shock or serious injury.
Close supervision is necessary when children, elderly, or persons with disabilities are in close proximity.
Keep all electrical components away from liquids or wet areas.
Do not sit or stand on desk. Do not crawl or lie under desk.
Do not place any object taller than 20” (when using glides) 23” (when using casters) under desk.
Never operate desk if cords / plug are wet or damaged.
Make sure there are no obstacles in the path of the desk’s motion.
Make sure all cords are appropriate length to accomodate desk’s motion.
Never exceed noted weight capacity.
Ensure all hardware are properly tightened.
If component needs to be replaced, remove power cord first.
In the event of a power outage or accidental removal of power cord, a manual reset may be necessary. See MANUAL RESET.
USE & LIABILITY
Read all instructions before using desk. Keep instructions for reference. Manufacturer does not accept warranty claims or liability claims for damages caused by improper use or handling.
CUSTOMER SERVICE
Page 3 of 8

Text on page 4
PARTS INCLUDED
NOT TO SCALE
A QTY: 2
B QTY: 2
C QTY: 1
D QTY: 2
E QTY: 2
F QTY: 1
G QTY: 1*
H QTY: 2
J QTY: 1
HARDWARE INCLUDED
1 QTY: 12 M8-10
2 QTY: 8 M8-20
3 QTY: 4 M6-10
TOOLS INCLUDED
NOT TO SCALE
4 QTY: 8 M6-12
5 QTY: 2 ST3.5-13
TOOLS REQUIRED
OR
Page 4 of 8

Page 5 of 8

Page 6 of 8

Page 7 of 8

Page 8 of 8 ยท End of manual
Quick start
- Check the parts: Compare the box with the Parts Included page. The hardware includes 12 M8-10, 8 M8-20, 4 M6-10, 8 M6-12 and 2 ST3.5-13. The desktop is sold separately.
- Tighten the hardware: Make sure all hardware is properly tightened before use. Do not open the handset, controller, legs or cables.
- Route the cords: Use cords long enough for the full range of motion and keep them dry. Never run the desk with wet or damaged cords or plug.
- Clear the path: Make sure nothing blocks the desk's motion. Nothing taller than 20 inches (glides) or 23 inches (casters) may sit under the desk.
- Move the desk: Push and hold the Up or Down key on the handset. The display shows height from 640mm to 1290mm.
- Save positions: Press and hold the first or second memory button for 5 seconds to save the current height. The auto saved memory position goes to 720mm.
- Mind the load: Stay within the 120 kg (256 lb) weight capacity. Do not sit or stand on the desk.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Memory button does not recall the height you wanted on the STANDE-60-BK/DW | The memory position was never saved, because the button needs a 5 second hold. | Raise or lower the desk to the height, then hold memory button 1 or 2 for 5 seconds to store it. Page 3 |
| Desk travels to 720 mm by itself | That is the auto saved memory position of the handset. | No repair needed. Use the Up and Down keys, held down, to move to another height within 640 to 1290 mm. Page 3 |
| Desk pulls on its cables while rising or lowering | The cords are too short for the travel range of the desk. | Use cords of a suitable length and keep the path clear of obstacles. Page 3 |
| Hardware rattles or the frame feels unsteady | Fasteners have loosened or the load is heavier than 120 kg (256 lbs). | Tighten all hardware and keep the load within the stated capacity. Page 3 |
| Child or other person tampers with the handset or controller | The handset, controller, legs and cables carry shock and injury risk. | Keep children away and supervise the elderly or people with disabilities. Never open these parts. Page 3 |
Frequently asked questions
Does the STANDE-60-BK/DW 60-inch desk come with a top?
No, the desktop is sold separately, and pictures may differ from the desk you receive. See page 2.
Can I stand or sit on the frame, or put things underneath?
No. Do not sit or stand on the desk, and do not crawl or lie under it. Keep objects taller than 20 inches (glides) or 23 inches (casters) out from under it. See page 3.
What should I do if the handset stops working after the cord is knocked out?
Check that all cables are seated and try the handset again. If that fails, unplug the power cable for 3 minutes, plug it in and retry. See page 3.
What is the auto saved memory height on this Luxor desk?
The auto saved position moves the desk to 720 mm. The two other memory buttons save a height when you hold them for 5 seconds. See page 3.
How many M8-20 screws are in the box?
The hardware list shows 8 pieces of M8-20, along with 12 of M8-10 and 4 of M6-10. See page 4.
