Page 1 of 11
Text on page 2
Flat Panel Cart Assembly Guide
Adjustable Height Flat Panel TV Cart with Media Shelf
Designed for 32”-65” TV Panels VESA: 100 x 100 - 600 x 400 Max Load Capacity: 100 lbs Media Shelf Max Load: 10 lbs
Page 2 of 11
Text on page 3
Table of Contents
Table of Contents and Warnings
- Installing the Casters and Poles
- Adjusting the Pole Height
- Installing the Media Shelf
- Installing the TV Mount
- Selecting the VESA pattern
- Attaching the TV to the Cart
Tools Required Phillips Screwdriver Tape Measure Wrench
Assistance Required
WARNING!
Severe personal injury and property damage can result from improper installation. Read instructions carefully before beginning.
Assistance is required when installing the TV. If you do not understand the instructions or have any concerns please contact a qualified local installer. Do not install or assemble if the product or hardware is damaged or missing, if you require replacement parts, contact your local dealer. This product fits most 40” - 60” flat panel displays; maximum eight for the disply is 100 lbs. Do not use this product for anything other than what it was originally designed. This product contains moving parts, please use caution. The manufacturer disclaims any liability for the modifications, improper installation, and installation exceeding maxium weight capacity. The manufacturer will not be liable for any damages arising out of the use of, or inability to use the product.
Page 3 of 11
Page 4 of 11
Text on page 5
1.1 Install casters to base
1.2 Install poles to base
Note: Make sure the cable management holes are facing the rear of the base
Page 5 of 11
Text on page 6
- Adjust the height of the telescopic mounting poles
Using your thumb or finger, depress the right upper pole spring plunger ball located at the cable window, and twist the upper pole 90 degrees. Pull the upper pole to your desired height, twist the upper pole toward the plunger holes, and engage the spring ball into the plunger hole and set as shown in Figure1.
Repeat with the left pole.
Page 6 of 11
Page 7 of 11
Page 8 of 11
Text on page 9
- Select your VESA pattern and attach TV brackets
Note:
To avoid damage, a spacer must be used when the mounting hole is minimal.
Page 9 of 11
Page 10 of 11
Page 11 of 11 ยท End of manual
Quick start
- Gather a Phillips screwdriver, a tape measure and a wrench, and have a helper for installing the TV.
- Install the casters to the base, then install the poles with the cable management holes facing the rear of the base.
- To set the height, press the spring plunger ball at the cable window, twist the upper pole 90 degrees, pull it to the height you want, twist it back and engage the ball in a plunger hole. Repeat on the other pole.
- Install the media shelf and the TV mount.
- Select your VESA pattern and attach the TV brackets, using a spacer where the mounting hole is minimal.
- Attach the TV to the cart with assistance.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Risk of injury or damage during installation | Improper installation. | Read the instructions before starting. Get help when installing the TV. If you have concerns, contact a qualified local installer. Page 3 |
| Parts are damaged or missing | The product or hardware is damaged or missing. | Do not install or assemble it. Contact your local dealer for replacement parts. Page 3 |
| TV is too heavy for the cart | The weight is over the limit. | Keep the TV at or under the maximum load of 100 lbs. The media shelf maximum is 10 lbs. Page 2 |
| Cable holes face the wrong way | The poles were installed in the wrong direction. | Install the poles so the cable management holes face the rear of the base. Page 5 |
| Cart height needs changing | The poles are at the wrong height. | Press the upper pole spring plunger ball at the cable window, twist the upper pole 90 degrees, pull it to the height you want, twist it back and engage the ball in the plunger hole. Repeat on the other pole. Page 6 |
| TV bracket may be damaged | The mounting hole is minimal. | Use a spacer when the mounting hole is minimal. Page 9 |
Frequently asked questions
What size TV does the FP2500 hold?
It is designed for 32" to 65" TV panels with VESA patterns from 100 x 100 to 600 x 400 (page 2).
What is the weight limit?
Maximum load capacity is 100 lbs. The media shelf holds up to 10 lbs (page 2).
How do I adjust the pole height?
Depress the spring plunger ball at the cable window, twist the upper pole 90 degrees, pull it to height, then twist it back so the ball locks into a plunger hole. Repeat on the left pole (page 6).
What tools are required?
A Phillips screwdriver, a tape measure and a wrench. A second person is required to install the TV (page 3).
