Page 1 of 4
Text on page 2
JT828P
Version #11 (0217) Approved by J. S.
JT828P is a 3.9-mil matte white, soft-calendared PVC film designed for UV and solvent-based ink jet printing. The product is coated on one side with a clear permanent, acrylic pressure sensitive adhesive and supplied with a 74# Kraft liner.
JT828P is designed for general purpose indoor and short term outdoor advertising and promotion on flat or slightly curved surfaces.
Physical Properties Property
Peel Adhesion lb./in. (N/25mm) 180° on glass
- 24 hr.
Quick Tack, lb./in² (N/25mm) Stainless Steel
FTM - 1
FTM - 9
Dimensional Stability, (%) 48 hours @ 158°F
Temperature Ranges Minimum Application: End Use:
40°F (+5°C)
- 5°F to 158°F (-20°C to 70°C)
FTM - 14 10” x 10” Sample Bonded to aluminum
The indoor durability of this film is 5 - 6 years and the outdoor durability of the unprinted film is up to 4 years. Over lamination of the inkjet-printed material with Permacolor ® overlaminates minimizes yellowing of the print media and delays color fading that may occur over time. This color fading is mainly dependent upon the inks quality (see technical data sheets given by the ink manufacturers) and the pressure sensitive media being used.
2 years from D.O.M. when stored at 60/77°F (15/25°C) and 50% relative humidity in the original package.
Page 2 of 4
Text on page 3
Approved Printing Processes:
Screen Printing: UV Cured Solvent Digital: UV Inkjet Eco-solvent True solvent Latex
HP Indigo Off-set Off-set UV Thermal Transfer Flexographic * Laser Jetrion
To achieve the best possible print quality, please make sure that the correct ICC profiles or printer settings are used. Profiles can be obtained from our Distributors or can be downloaded from www.MyBinding.com . Printer and heater settings and ICC profiles can also be downloaded from some O.E.M. or software manufacturer’s websites.
The ICC profiles are provided solely as a customer resource. Print environments, the individual nature of printing systems, inks and software can significantly affect output. It is the customer’s responsibility to determine the suitability of any profile for use in their specific print environment.
- The user is responsible for determining the product’s suitability, including adhesion and if needed, removal characteristics when used in applications other than listed specifically in this Performance Guide.
- If there are any questions about applications, please contact your Mactac sales representative to discuss your requirements for recommendations.
- If this is a printed Performance Guide it is an uncontrolled document. Please check the Mactac website for the latest, most up-to-date version.
Always test your combination of IMAGin products, inks and laminating films prior to commercial use.
- Printing Conditions: Print in conditioned pressroom at ±73°F (23°C) and 50% RH. Ink saturation
should not exceed 270%.
- Drying Requirements: Solvent, Eco-solvent and Mild-solvent inkjet prints require 24 - 48 hr. drying time - open to the air. Inks do not dry when printed media is rolled up. The prints must be dry prior to lamination.
- Laminating Conditions: If the printed graphic is likely to be exposed to corrosive liquids, smoke, fumes and highly polluted areas or there is a likelihood of scratching it is highly recommended you laminate with Permacolor ColorGard LUV series (intermediate) or PromoGard (economical) overlaminating films. Please be aware that adding an overlaminate will significantly reduce conformability to complex surfaces.
- Transportation Conditions: To allow for easy transportation, IMAGin series can be rolled up, with the image out, with a minimum diameter of 6 inches (15cm). When the image is not protected by an overlaminate, make sure the print is completely dry and protected in a plastic bag. During transportation or storage, avoid exposing them to extreme temperature and humidity changes.
Page 3 of 4
Text on page 4
Values given are typical and are not necessarily for use in specification.
CALL 1-800-321-8834 for additional product information
IMPORTANT NOTICE: The information given and the recommendations made herein are based on our research and are believed to be accurate, but no guarantee of their accuracy or completeness is made. In every case, user shall determine before using any product in full scale production, or in any way, whether such product is suitable for user’s intended use for their particular purpose under their own operating conditions. User assumes all risk and liability whatsoever in connection with their use of any product. The products discussed herein are sold without any warranty as to merchantability or fitness for a particular purpose, or any other warranty, express or implied. No representative of ours has any authority to waive or change the foregoing provisions, and no statement or recommendation not contained herein shall have any force of effect unless in an agreement signed by the officers of seller and manufacturer. Nothing contained herein shall be construed to imply the nonexistence of any relevant patents or to constitute a permission, inducement or recommendation to practice any invention covered by any patent without authority from the owner of the patent. The following is made in lieu of all warranties, express or implied: Seller’s and manufacturer’s only obligation shall be to replace or credit such quantity of the product proved to be defective at its discretion.
Page 4 of 4 · End of manual
Quick start
- Print in a conditioned pressroom at about 73°F (23°C) and 50% RH, keeping ink saturation at or below 270%.
- Let solvent, eco-solvent and mild-solvent prints dry 24 to 48 hours open to the air before laminating.
- Laminate with Permacolor ColorGard LUV or PromoGard if the graphic faces chemicals, pollution or scratching.
- Roll prints image-out on a core of at least 6 inches diameter for transport, bagging unlaminated prints.
- Apply at 40°F (5°C) or warmer on flat or slightly curved surfaces.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| JT828P will not stick when applied in a cool room | The room is below the minimum application temperature | Apply at 40°F (+5°C) or warmer. Page 2 |
| You are unsure your print process can be used | The process is not on the approved list | Approved processes include screen printing, UV cured, UV inkjet, eco-solvent, true solvent and latex digital, HP Indigo, offset, UV offset, thermal transfer, flexographic, laser and Jetrion. Page 3 |
| The film is old and performs poorly | It was kept past its shelf life | Shelf life is 2 years from D.O.M. when stored at 60/77°F (15/25°C) and 50% relative humidity in the original package. Page 2 |
| The finished graphic sees extreme heat or cold | The temperature is outside the end-use range | Keep it within 5°F to 158°F (-20°C to 70°C). Page 2 |
| A new film, ink and laminate mix gives unexpected results | The combination was not tested | Always test your combination of IMAGin products, inks and laminating films before commercial use. Page 3 |
| A printed copy of this guide may be out of date | A printed Performance Guide is an uncontrolled document | Check the Mactac website for the latest version. Page 3 |
Frequently asked questions
How long does JT828P last?
Indoor durability is 5 to 6 years, and the unprinted film lasts up to 4 years outdoors. See page 2.
Which printers and inks can I use?
Approved processes include UV inkjet, eco-solvent, true solvent and latex digital printing, plus screen, offset, thermal transfer and other methods. See page 3.
Should I laminate the print?
Overlaminating with Permacolor minimizes yellowing and delays color fading, and is highly recommended where prints face chemicals, pollution or scratching. Lamination reduces conformability. See page 2 and page 3.
What is the shelf life?
2 years from date of manufacture when stored at 60 to 77°F (15 to 25°C) and 50% RH in the original package. See page 2.
What temperatures can it handle?
Minimum application temperature is 40°F (+5°C), and the end-use range is -20°C to 70°C. See page 2.
