Marlon 350E Auto Crimper Service Manual, page 1

Page 1 of 19

Marlon 350E Auto Crimper Service Manual, page 2

Page 2 of 19

Marlon 350E Auto Crimper Service Manual, page 3
Text on page 3

INTRODUCTION

Your new Marlon 350 Auto Crimper is designed to increase your plastic spiral binding production. The Marlon 350 is an inexpensive yet extremely versatile tabletop machine. The Marlon 350 cuts and crimps 6mm through 50mm coil, with an adjustable binding length from 3.5-inches to 14-inches. The Marlon 350 is capable of 50 cycles per minute, and features a coil waste chute that uses standard plastic grocery bags for clipping waste containment. The Marlon 350 is an operator friendly machine that is easy to set up, allowing for quick changeover from one coil diameter to another. We are confident that your new Marlon 350 Auto Crimper will be a valuable asset to your plastic coil binding operation. The following pages of this manual will cover machine setup, operating procedures, and trouble shooting your Marlon 350 Auto Crimper.

WARNING: Changing of cutting blades should be done only by trained service personnel. Disconnect power from unit before servicing.

Page 3 of 19

Marlon 350E Auto Crimper Service Manual, page 4
Text on page 4

MARLON 350E CONNECTIONS

COIL WASTE CHUTE

PLACE BAG

HANDLES IN THESE SLOTS TO HOLD BAG

THE COIL WASTE CHUTE USES STANDARD PLASTIC GROCERY BAGS

FOR CLIPPING CONTAINMENT. PLACE THE HANDLES OF THE BAG IN THE SLOTS ON BOTH SIDES TO HOLD THE BAG IN PLACE.

Page 4 of 19

Marlon 350E Auto Crimper Service Manual, page 5
Text on page 5

BLADE SELECTION

The Marlon 350 Auto Crimper features interchangeable cutter blades. Your Marlon 350 was shipped with the B-size cutter blades installed. Use the following chart to determine what blade size is required for the coil diameter your crimping.

A-size blades: 6mm and 7mm coil

Note: Over sized punch patterns (.248) or punch patterns with a large backstop (distance from paper edge to hole) will not work well with the A – size cutter head.

B-size blades: 8mm through 25mm coil C-size blades: 12mm through 50mm coil

The cutter blades and cutter head assemblies have been color coded to reduce the chance of improper assembly.

Universal parts of the cutter head assembly that are used for all three sets of knives are marked white. These parts are used all of the time.

A-size parts of the cutter assembly are marked red.

B-size parts of the cutter assembly are marked green.

C-size parts of the cutter assembly are marked yellow.

Note: Some parts of the cutter assembly are marked with two colors. These parts are used on two of the three cutter assembly configurations.

Page 5 of 19

Marlon 350E Auto Crimper Service Manual, page 6
Text on page 6

CUTTER HEAD ASSEMBLY

Cam Arm Arm drive Screw

Cutter blade assembly Clamp blade stop Cam micro switch Clamp blade stop mtg. holes 1, 2 Hole # 1, will provide a wider blade gap Suitable for larger coil / filament Hole # 2 accommodates smaller coils / Filament size

Page 6 of 19

Marlon 350E Auto Crimper Service Manual, page 7
Text on page 7

B-SIZE CUTTER BLADE ASSEMBLY

LEFT CUTTER HEAD

RIGHT CUTTER HEAD

LEFT BASE PLATE

A, B & C – SIZE ANVIL BLADE

RIGHT BASE PLATE

B – SIZE .126” SPACERS

CLAMP SPRING

B – SIZE CUTTER BLADE

B & C – SIZE CLAMP BLADE

B & C – SIZE-FORMING BLADE

B & C – SIZE-FORMING BLADE

CLAMP SPRING

B – SIZE CUTTER BLADE

B & C – SIZE CLAMP BLADE

B – SIZE .126” SPACERS

CLAMP STOP 1/4 X 1-1/2

SHOULDER BOLT

A, B & C – SIZE ANVIL BLADE

FOR B – SIZE ASSEMBLY

ONLY .062 SPACER

CLAMP STOP 1/4 x 1-1/2 SHOULDER BOLT

10-24 NYLOCK NUTS

10-24 NYLOCK NUTS

NOTE: THE RIGHT CUTTER BLADE ASSEMBLY IS UP SIDE DOWN. THE SAME FOUR BLADES ARE USED ON BOTH SIDES, BUT THEY ARE INSTALLED IN EXACTLY THE OPPOSITE ORDER.

Page 7 of 19

Marlon 350E Auto Crimper Service Manual, page 8
Text on page 8

Pictured above is the B-size cutter blade assembly. The following information describes the changes needed to switch from the B to A-size and B to C-size cutter assemblies. Refer to the color codes on page four to select the proper parts when changing from one blade configuration to another. Refer to pages five and six for part descriptions.

Changing from B to A-size blades:

1.)Disconnect the power cord from Marlon 350. 2.)Remove the top cover from the machine. 3.)Remove the clamp stop shoulder bolts from each side 4.)Remove the three 10-24 nylock nuts from each side. 5.)The left clamp blade is now free and can be removed. 6.)Remove the right anvil blade by lifting it straight up. 7.)Remove the left forming blade by lifting it straight up. 8.)Detach the right cutter blade from the drive pin. (the right cutter blade is now free.) 9.)Remove the two .126” B-size spacers from each side. 10.)Remove the right forming blade by lifting it straight up. The right clamp blade is now free. 11.)Detach the left cutter blade from the drive pin, the arm drive screw must be loosened to free cutter blade. (See step 8 for details.) 12.)Leave the left anvil blade on, because it’s used in all three setups. 13.)Reassemble the cutter blade assemblies in reverse order using the correct color-coded parts. 14.)Use the fifth .094” A-size spacer instead of .062spacer on the left hand shoulder bolt.

Page 8 of 19

Marlon 350E Auto Crimper Service Manual, page 9
Text on page 9

A-KIT COIL GUIDE INSTALLATION

PICTURED ABOVE ARE THE COIL GUIDES INSTALLED ON

THE CUTTER ASSEMBLY. THESE GUIDES ARE ONLY USED WITH THE A-SIZE BLADE CONFIGURATION. THE COIL GUIDES ARE STAMPED “L” FOR LEFT AND “R” FOR RIGHT AND ARE ALWAYS INSTALLED WITH THE LETTERS UP. YOU HAVE TWO “L” GUIDES ONE MARKED “L” AND ONE MARKED “L 6”. THE “L 6” IS USED FOR 6mm DIA. COILS ONLY.

Page 9 of 19

Marlon 350E Auto Crimper Service Manual, page 10
Text on page 10

Changing from B to C-size blades:

1.)Disconnect the power cord from Marlon 350. 2.)Remove top cover from machine. 3.)Remove the clamp stop shoulder bolts on both sides. 4.)Remove the three 10-24 nylock nuts from each side. 5.)The left clamp blade is now free and can be removed. 6.)Remove the right anvil blade by lifting it straight up. 7.)Remove the left forming blade by lifting it straight up. 8.)Detach the right cutter blade from the drive pin. (The right cutter blade is now free.) 9.)Remove the two .126” B-size spacers from each side. 10.)Remove the right forming blade by lifting it straight up. The right clamp blade is now free. 11.)Detach the left cutter blade from the drive pin, the arm drive screw must be loosened to free cutter blade (See step 8 for details.) 12.)Leave the left anvil blade on, because it is used in all three setups. 13.)Change the clamp stop to its correct hole position. 14.)Reassemble the cutter blade assemblies in reverse order using the correct color-coded parts. 15.) Note: No washers or spacer is used on the left-hand shoulder bolt when using the C-size blade configuration.

Page 10 of 19

Marlon 350E Auto Crimper Service Manual, page 11
Text on page 11

C-CUTTER BLADE INSTALLATION

REAR HOLE OF THE

C-CUT BLADE IS NOT USED IN THIS MODEL.

IN YOUR “C” KIT

THIS HOLE IS PLUGGED.

INSTALL THE DRIVE

PIN IN THE OPEN HOLE.

PICTURED ABOVE ARE THE C-SIZE CUTTER BLADES AS

FURNISHED IN THE “C” KIT SHIPPED WITH YOUR MACHINE.

Page 11 of 19

Marlon 350E Auto Crimper Service Manual, page 12
Text on page 12

CLAMP STOP POSITIONS

Mount the clamp stop in the first hole for C-size blade configuration.

Mount the clamp stop in the second hole for A and B-size blade configurations.

These stop positions allow adjustment of blade opening for coil Insertion and the above are suggested settings. Some B size coils Might work well in the first hole position. Filament size and coil Pitch will be the factors involved.

Page 12 of 19

Marlon 350E Auto Crimper Service Manual, page 13
Text on page 13

TABLE ADJUSTMENTS

Now that you have the correct blade configuration ready for the coil diameter you are crimping you need to adjust the table height and cutter head spacing (width) for your book. Refer to page 13 for table adjustment details.

1.)Loosen the two clamp knobs on the left-hand book guide; position the guide so your book will be approximately centered on the machine. Re tighten the two clamp knobs. 2.)Using the same procedure position the right-hand book guide so it just touches the right edge of the book. The book should lay flat on the table between the book guides and be able to slide in and out, but not side to side. 3.)Use a #3 Phillips screwdriver to loosen the two bolts located under the two access holes in the top cover. The two cutter heads will now be able to slide from side to side. Slide the two cutter heads so the cutter blades are close to the correct loop of the coil at each end of the book. 4.)Make a rough adjustment on the table height by turning the two table height knobs. Turn the knobs clock-wise to lower the table and counter clock-wise to raise the table. Adjust the table height so the coil in the book is in the center of the cutter blade assembly on both sides. The right side of the table will always be adjusted higher than the left side. 5.)Adjust the two cutter heads from side to side until the coil in the book slides into the cutter blades at the correct loop of the coil on each side of the book 6.)Make a finer adjustment to the table height so the coil in the book is properly positioned in the center of the cutter blades. 7.)Make your final cutter head adjustments side to side if needed and then re tighten the two bolts under the access holes of the top cover using the #3 Phillips screwdriver. 8.)Test crimp a book by depressing the foot pedal. 9.)Make your final table height adjustments if needed. Then repeat steps #8 and #9 until the desired crimp is achieved.

Page 13 of 19

Marlon 350E Auto Crimper Service Manual, page 14
Text on page 14

TABLE ADJUSTMENT DETAILS

TWO ACCESS HOLES

IN TOP COVER

TABLE HEIGHT

ADJUSTER KNOBS: ONE ON EACH SIDE

BOOK GUIDES: ONE ON

EACH SIDE

CLAMP KNOBS:

TWO ON EACH BOOK GUIDE

Page 14 of 19

Marlon 350E Auto Crimper Service Manual, page 15
Text on page 15

TROUBLE SHOOTING GUIDE

PROBLEM

CRIMPER DOESN’T CYCLE

COIL IS BEING CRIMPED BUT NOT

CUT POWER ON DOESN’T CYCLE

SOLUTION

VERIFY THAT POWER IS PLUGGED IN AND TURNED ON ADJUST TABLE HEIGHT FOR PROPER ALIGNMENT RESET FUSES

Page 15 of 19

Marlon 350E Auto Crimper Service Manual, page 16
Text on page 16

Heads with A-Blades installed

A-Blade Parts Layout in Order of Use

Page 16 of 19

Marlon 350E Auto Crimper Service Manual, page 17
Text on page 17

Heads with B-blades installed

B-Blade Parts Layout in Order of Use

Page 17 of 19

Marlon 350E Auto Crimper Service Manual, page 18
Text on page 18

Heads with C-blades installed

C-Blade Parts Layout in Order of Use

Page 18 of 19

Marlon 350E Auto Crimper Service Manual, page 19

Page 19 of 19 ยท End of manual

Quick start

  1. Hang a standard plastic grocery bag on the coil waste chute by placing its handles in the slots on both sides.
  2. Check the installed blades match your coil: A-size for 6 and 7 mm, B-size (factory installed) for 8 to 25 mm, C-size for 12 to 50 mm.
  3. Loosen the book guide clamp knobs and set the guides so the book is roughly centred and slides in and out without side play.
  4. Loosen the two bolts under the top cover access holes with a #3 Phillips screwdriver and slide the cutter heads near the correct coil loop at each end.
  5. Turn the table height knobs (clockwise lowers, counter-clockwise raises) so the coil sits in the centre of the blades; the right side is always higher than the left.
  6. Fine-tune head position and table height, retighten the bolts, then press the foot pedal to test crimp and adjust until the crimp is right.

Troubleshooting

ProblemLikely causeFix (from the manual)
Crimper doesn't cyclePower is not connected or switched on.Verify the machine is plugged in and turned on. Page 15
Coil is crimped but not cutThe coil is not aligned correctly in the cutter blades.Adjust the table height for proper alignment. Page 15
Power is on but the machine doesn't cycleFuses have tripped.Reset the fuses. Page 15

Frequently asked questions

What coil sizes does the Marlon 350E handle?

6 mm through 50 mm plastic coil, with a binding length adjustable from 3.5 to 14 inches (page 3).

Which cutter blades do I need?

A-size for 6 and 7 mm coil, B-size for 8 to 25 mm and C-size for 12 to 50 mm. Parts are color coded: white universal, red A, green B, yellow C (page 5).

How fast is the 350E?

Up to 50 cycles per minute (page 3).

Where should the clamp stop be mounted?

In the first hole for C-size blades and the second hole for A and B-size blades. Some B-size coils may work better in the first hole (page 12).

Who should change the cutter blades?

Only trained service personnel, with power disconnected (page 3).