

Page 1 of 8

Text on page 2
Thank you for your purchase of the Martin Yale Industries, Inc. 1501X Autofolder. Upon receiving the machine, perform an inspection of all components received. If you suspect that the unit may have been damaged in transit, call the appropriate freight carrier immediately. If you have any additional questions, please contact Martin Yale Industries, Inc. Customer Service department at 260- 563-0641.
Upon receiving the machine, verify that you have the following components:
First Fold Table Second Fold Table L Shaped Catch Tray 24 VDC Adapter Extension Table Feed Table Wedge
1501X SPECIFICATIONS
PAPER WEIGHT: 16# - 24# BOND STOCK
MIN./ MAX WIDTH: 3 ½” – 8 ¾” MIN./ MAX LENGTH: 5” – 14” MAX FEED LOAD: 250 SHEETS (20# BOND STOCK). SPEED: 5,000 – 8,000 PER HOUR. POWER CONSUMPTION: 24 VDC (1A)
UNIT IS PROTECTED BY A PTC STYLE CIRCUIT BREAKER. SHOULD IT LOSE POWER FOR ANY REASON, TURN UNIT OFF FOR 60 SECONDS. IF POWER DOES NOT RETURN, CALL TECHNICAL SUPPORT AT Martin Yale Industries, Inc. AT 219-563-0641.
Page 2 of 8

Text on page 3
First step is to plug into wall outlet. The power adaptor connects on the inside frame, under the feed table. Once plugged in, toggle the power switch and make sure there is power to the motor*.
FEED TABLE EXTENSION
Extension Table
Extension Table locking pins.
The feed table extension is slotted on the bottom, and goes onto a dual set of pins on the left and right side of the feed table. (See photo above.)
LOADING THE MACHINE- SINGLE SHEET APPLICATION
To load the feed table, position paper guides at proper width and insert stack. Square the guides with the paper. Do not allow the guides to pinch the stock, but, do not leave a great deal of room in between the side edges of stock and the guides.
Stack of paper should be squared against the retarder frame for proper feeding.
1/16” clearance between paper guides and the sides of the stack.
- Some units may not have a detachable power cord.
Page 3 of 8

Text on page 4
When putting paper into the machine, it should be a neat stack. Once the stack is on the tray, press down and slide the stack against the retarder frame. After squaring, allow the table to return to its upper position. At this point, the stack of paper should be pressed against the feed roller.
SETTING THE FOLDS
In order to use the unit, you must first understand the different fold setups.
The first consideration is how to do a half fold as opposed to a tri- fold. in order to do this, the second folding table must be repositioned on its mounting post to disable it. (See photo below.)
First step in doing a half fold.
This is accomplished by pulling out o n the bottom edge of the second folding table and lowering it slightly so that is is aligned with the rubber grommet that says ‘single fold’. When resecuring the table onto the mounting post, make sure it is fully pressed into position. After this is performed, the second folding table will be disabled and the table underneath the feed tray needs to be set for the appropriate sheet size. This is typically going to be a half fold. There are icon markings on the ruler for A4, 8 ½ X 11 and 8 ½ X 14.
When adjusting the paper stop brackets on the fold tables, make sure that they are straight in alignment. Also, when tightening the knobs, be careful not to over tighten.
Any time there are two folds in the stock, like a typical letter fold, the second fold tables mounting post should be inserted into the double fold opening. (See photo on next page.)
Page 4 of 8

Text on page 5
Post goes into double fold hole during a letter fold.
NOTE: When doing two folds, make sure that both folding tables are pointing to an identical icon.
LOADING THE MACHINE- MULTIPLE PAGE SETS
Your unit is capable of folding up to three pieces of 20# bond stock at one time. This must be done by hand feeding the machine through the top of the bonnet.
Load multiple page sets here, one set at a time.
NOTE: Your unit can run stapled sets, but they must be stapled parallel to the top edge, and the staple must be centered. Also, when hand feeding sets into the machine make sure that you use the engaging clip to hold the feed table in the down position. If this were not done, it could cause premature wear of the feed tire.
Page 5 of 8

Text on page 6
MAINTENANCE
Clean the folding rollers of the machine once every 15 thousand folds. Do this by removing the spring loaded bonnet assembly. You will need a can of Rubber Roller Cleaner and a 3M Scotch-brite pad. Clean each roller throughly by rotating by hand to scrub each section. Use an old cloth to mop up any liquid residue that may be left over. Also, from time to time the feed tire of the unit may become soiled and need to be cleaned. In this case, soap and warm water would be ideal.
Should the machine become labored, apply one drop of lubrication to each of the units folding roller bushings. A light weight all purpose lubrication is recommended for this.
TROUBLESHOOTING
UNIT WILL NOT RUN:
Turn power to unit off for 60 seconds and try again. If still no power, verify a good plug in by plugging in another device. Also, in the power jack on the machine there is a metal spring clip. It is possible over a period of time that the clip could get bent and no longer make good contact. With a n unfolded paper clip, bend the bracket outward to make sure it provides good contact. If there is still no power, call Martin Yale Industries, Inc. technical support at 219-563-0641.
WRINKLED FOLDS
Clean rollers, make sure that you allow the stock time to cool (one hour). Do not place the machine on a metal table, and try to operate unit in a temperature controlled environment. If unit still wrinkles paper, call Martin Yale Industries, Inc. technical support at 219-563-0641.
PAPER WILL NOT FEED
Make sure the paper guides are not pinching the stock. Monitor the feed tire for wear and tear. Replace if excessively warn. Allow the stock time to cool (one hour) after being duplicated. NOTE: If stock has a slick finish, friction fed folders in general have difficulty feeding and folding this type of paper.
CROOKED FOLD
Make sure that each of the paper stops are lined up straight, and stack is properly inserted. If due for a cleaning or if you suspect that some characteristic of your stock could cause rapid contamination, thoroughly clean the rollers of the unit. Always suspect dirty rollers when any fold machine starts giving fold
Page 6 of 8

Text on page 7
offages under normal settings. Make sure there is no gappage in between the side edges of the stock and guides that hold it straight as it feeds into the unit.
SMUDGING
Typically, there is nothing that can be done to a friction fed unit that will prevent this. Adjusting toner, inking or the amount of drying time are all good suggestions. This issue can be particularly tough on stocks that are printed on both sides.
JAMS
Follow the below steps to clear a jam:
Remove the spring loaded bonnet assembly (shown above).
Manually rotate rollers by spinning the center rubber roller, and one of the rollers next to it together.
If necessary, remove each of the folding tables by disengaging off of mounting pin and lowering down until it separates.
Page 7 of 8

Text on page 8
This should provide you with all necessary info to operate the unit. If you have any further questions , please call the technical support division at Martin Yale Industries, Inc., we will be glad to assist you.
Page 8 of 8 ยท End of manual
Quick start
- Check that you received the first and second fold tables, L-shaped catch tray, 24 VDC adapter, extension table and feed table wedge.
- Plug the adapter into the wall and into the frame under the feed table, then toggle the power switch.
- Slide the slotted feed table extension onto the pins on each side of the feed table.
- Set the paper guides to the stack width with about 1/16" clearance, press the stack down and square it against the retarder frame.
- For a half fold, lower the second fold table to the single fold grommet; for a letter fold, insert its post in the double fold opening.
- Set the fold table paper stops to the same size icon (A4, 8 1/2 x 11 or 8 1/2 x 14) and keep the stop brackets straight.
- Hand-feed sets of up to three 20# sheets through the top of the bonnet, with the feed table clipped down.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Unit will not run | The PTC circuit breaker has cut power, the outlet is bad, or the spring clip in the power jack is bent | Turn the unit off for 60 seconds and try again. Test the outlet with another device. Bend the metal clip in the power jack outward with an unfolded paper clip so it makes contact. Page 6 |
| Wrinkled folds | Dirty rollers, warm stock, or operating on a metal table | Clean the rollers, let freshly printed stock cool for one hour, keep the folder off metal tables and run it in a temperature-controlled room. Page 6 |
| Paper will not feed | Guides pinching the stock, a worn feed tire, warm stock or slick-finish paper | Loosen the paper guides, replace an excessively worn feed tire and let duplicated stock cool for an hour. Slick stock is hard for any friction-fed folder. Page 6 |
| Crooked fold | Paper stops out of line, stack inserted wrong, dirty rollers or a gap between stock and guides | Line up the paper stops, reinsert the stack, close any gap at the guides and clean the rollers. Page 6 |
| Smudging | Friction feeding on wet ink or toner, especially on two-sided prints | Adjust toner or ink coverage, or allow more drying time before folding. Page 7 |
| Paper jam | Paper caught in the rollers or fold tables | Remove the spring-loaded bonnet, turn the center rubber roller and its neighbor together by hand, and remove the fold tables from their mounting pins if needed. Page 7 |
Frequently asked questions
What paper sizes and weights does the 1501X fold?
It folds 16# to 24# bond stock from 3 1/2" to 8 3/4" wide and 5" to 14" long. See page 2.
How fast is the 1501X and how much does the feed table hold?
It runs 5,000 to 8,000 sheets per hour, and the feed table holds 250 sheets of 20# bond. See page 2.
Can the 1501X fold stapled sets?
Yes, hand-fed through the top of the bonnet, up to three 20# sheets at a time. The staple must be centered and parallel to the top edge, and the feed table should be clipped down. See page 5.
How often should I clean the rollers?
Every 15,000 folds. Remove the spring-loaded bonnet and scrub each roller with rubber roller cleaner and a Scotch-Brite pad while turning it by hand. Clean the feed tire with soap and warm water. See page 6.
