

Page 1 of 3

Text on page 2
CAUTION
DO NOT insert thick cardboard, metal, hard paper, etc. into the letter opener
Desktop Letter Opener
DO NOT feed envelopes fastened with staples or paper clips.
DO NOT touch the cutters with your ngers.
Operating Instructions
Parts List
M-S162811 M-S162812 MRA161609 MRA161610
Envelope Exciter Drive Belt Lower Cutter Blade Upper Cutter Blade
251 Wedcor Avenue, Wabash, IN. 46992 Toll Free: 1.800.225.5644 Fax: (260) 563.4575 Email: info@martinyale.com Website: www.martinyale.com
Warning: Never connect power to this product until you are ready to use the letter opener. The AC outlet used for this machine must be nearby and must not be blocked. This machine contains moving parts that can catch hair, loose clothing or jewelry. During operation and maintenance, keep hair, loose clothing and jewelry clear of moving parts. Disconnect the power cord from the wall outlet before attempting any service to the unit, and before removing the cover for any reason.
Attention: For equipment that plugs in, the socket/outlet shall be installed near the equipment and shall be readily accessible.
Page 2 of 3

Text on page 3
Unpack the unit and plug the power cord into a power outlet. The unit should turn on when depressing the start button on the top cover and shut off when releasing the start button.
NOTE: If unit jams during operation, unplug the unit and clear all jams. Then reinstall the power plug.
Step 3. Momentarily depress the START button to begin the feeding process. You may release the START button when envelopes begin exiting the unit.
Step 1. Prepare up to 10 standard envelopes to be opened by tapping the top sealed ap side down rmly on desktop several times.
This will cause the envelope contents to slide to the opposite side of that to be opened.
Step 2. Place up to 10 prepared envelopes onto the feed tray with the bottom edges of the envelopes back against the opener housing and also against the top cover that contains the START button.
Step 4. Depending on the condition of the envelope edges and atness, the entire stack should automatically feed until the stack is completed. However, under previously mentioned conditions of the envelopes, you can depress the START button to begin feeding again if it hesitated and did not complete the stack.
Step 5. Your stack of envelopes will be stacked on the right side of the unit and the scrap is easily separated from your opened envelopes. The cut edges of your envelopes are cut such that they are unlikely to cut or injure ngers.
Page 3 of 3 · End of manual
Quick start
- Unpack the unit and plug it into a nearby, accessible outlet.
- Tap up to 10 envelopes, sealed flap side down, firmly on the desk so contents slide away from the edge to be opened.
- Place the envelopes on the feed tray, bottom edges against the opener housing and the top cover.
- Momentarily press START; release it once envelopes begin exiting.
- If feeding hesitates before the stack is done, press START again.
- Collect opened envelopes on the right side and separate the scrap.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Unit jams during operation | Envelope caught in the feed path | Unplug the unit, clear all jams, then plug it back in. Page 3 |
| Stack stops feeding before it is finished | Envelope edge condition or flatness | Press the START button again to resume feeding. Page 3 |
Frequently asked questions
How many envelopes can the 1628 open at once?
Load up to 10 standard envelopes on the feed tray. See page 3.
Can I feed envelopes with staples or paper clips?
No. Do not feed fastened envelopes, thick cardboard, metal or hard paper. See page 2.
What are the replacement blade part numbers?
Lower cutter blade MRA161609 and upper cutter blade MRA161610. See page 2.
What is the drive belt part number?
The drive belt is M-S162812; the envelope exciter is M-S162811. See page 2.
