

Page 1 of 9

Text on page 2
Operating Instructions SP100, BCS400 series
1.0 Introduction
Thank you for your purchase of the intimus ® line of Business Card Slitters or Scoring/Perforating machines. With proper maintenance your unit will provide you with years of service. Upon receiving the machine verify that there are no signs of shipping damage on the exterior. If you feel the product may have been damaged in transit, contact the appropriate freight carrier immediately, then contact technical support at Martin Yale Industries, Inc. at 260-563-0641. Upon opening the machine, verify that you have the following components.
2.0 Inventory of Contents
SP100 Unit Catch Tray W-ODT0021 Paper Support W-ODT1124 3/32" T- Handle Allen M-S012012 Operating Instructions 8.5" Top Plate W-ODT0100 11.0" Top Plate W-ODT0200
BCS400 Series Unit Receiver Tray W-ODT0024 Receiver Base Form W-ODT0023 Paper Support W-ODT1124 T- Handle 3/32" Allen M-S012012 10 - Up Catch Tray W-ODT0021 12 - Up Catch Tray W-ODT0020 Operating Instructions 8.5" Top Plate W-ODT0100 11.0" Top Plate W-ODT0200
Model: Serial No: Manuf. Date:
3.0 Specifications
> Accessory shafts can be easily disassembled for addition of optional components. > Units will handle 24# bond to 100# cover stock. > Min. Sheet Size 4 1/8" X 3 ½" > Max. Sheet Size 8 ½" X 11" > Speed: BCS412: 300 finished cards per minute. BCS410: 375 finished cards per minute. SP100: 1400 8 ½" X 11" sheets per hour.
SHIPPING WEIGHTS
- MODEL SP100
- MODELS 410&412
23 lb# 44 lb#
Page 2 of 9

Text on page 3
4.0 Set up from carton to table
Caution: The unit contains rotating blades and other dangerous items. Do not remove any safety cov-
ers from the machine. Be aware that loose jewelry, long hair and loose fitting clothes should be kept away from the unit.
1. Set the machine on a tabletop. Verify the power switch is set to "0" (off position).
2. Look in each feed shelf of your unit, and verify that the tips of the sheet retarder are not in contact with the feed wheels. These are preset at the factory and should not need to be adjusted. Note: If the machine is operated with the retarder in contact with the feed wheels the wheels could be damaged. Retarder Make sure that the sheet Retarder is factory set to .012 retarder tips are not touching gap and should not need to be the feed wheel in each shelf adjusted for typical 65# stock. when the machine is turned on.
2a. Remove taped accessories from the exit tray shelves. These are used as paper weights on top of the stack to insure accurate tracking of curled stocks, or for stocks that require additional control for accurate feeding and registration. See Figure 2.
Make sure that the stack weights are removed from the feed bins before the machine is run for the first time.
3. Turn rocker switch to "1" . The unit should begin running. If there is no power, try the following:
3a. Check the electrical outlet to verify function. A good way to do this is to plug in another device that you know works.
3b. If still no power, check that circuit breaker has not tripped. Find source of machine bind and correct. Allow machine to cool and push breaker in to reset.
3c. Call the technical support division at Martin Yale Industries, Inc. at 260-563-0641.
Tray/ Paper Support Installation
Depending on the model, install the paper support and collection bins onto the machine. A paper support is utilized on the in feed of any bin where the sheets overhang the edge of the feed shelf. The paper support is installed by inserting the tabs into the slots on the front of the feed shelves as shown in Figure 3. Also, for units that make business cards, the bottom shelf will be where the first pass is made and the shelf above it will be where the finished product is created. NOTE: On the 400 series the bottom stacking tray and paper support can be moved to the top shelf for stacking of scored or perforated stock. See Figure 4 for correct location of collection trays on the 400 series business card slitters.
Collection bin for finished cards goes on middle shelf; large collection tray goes on top or bottom.
Page 3 of 9

Text on page 4
5.0 Setting Registration
Note: The registration is preset at the factory and should not be adjusted unless it is determined that it is not correct for the stock being used.
Perform the following steps in order to achieve accurate registration.
- Loosen the thumb knobs on the paper guides for the appropriate shelf (see Figure 5).
- Raise retarder up using the thumb knob on the side of the machine (rotate counter-clockwise) until stock will easily slide under retarder (Figure 7, Below.)
- Align register marks on layout sheets with the cutter blade edges (Figure 8).
- Position paper guides so that side-to-side movement will be no more than 1/32". NOTE: The guides should not pinch the stock. Inaccurate feeding could result if too tight (Figure 9).
- Feed single sheets to test for accuracy. Readjust paper guides as necessary.
NOTE: You may want to use unprinted stock for initial start up to remove residual oil from cutting blades.
Retarder Knobs
Paper Guide Thumb Knobs (3 Pairs)
Stock Retarder
Align Register Marks with Blades
Register Marks (on Layout Sheet)
Paper Guide to Stock Adjustment Watch for Pinching of Stock at These Points
Verifying a square cut:
To verify that the finished product is square, take a stack of business cards and divide in half. Flip ½ over and recombine. All edges should align evenly. If edges do not align, the stock is skewing. See skewing section under 7.0 Troubleshooting.
Page 4 of 9

Text on page 5
Proper Feeding
NOTE: The feed is preset for 65# stock and typically does not require readjustment. Registration should be set before setting the retarder for single sheet feeding.
Follow these steps:
- Using the adjustment knob on the front of the feed shelf, position feed pressure arm so that it is just above the feed wheel. Make sure there is no contact. (Figure 10). Pressure arm should rest just out of contact with the feed wheel.
- Using the adjustment knob on side of feed shelf, raise retarder off feed wheel. Insert one piece of stock to be ran in between the retarder and feed wheel so that sheet passes freely. Lower retarder so that there is a slight drag on the stock as it is pulled out.
- Place a neat stack of three sheets into the unit and test. Readjust as necessary until one sheet feeds steadily.
Feeding Thermographic or severely curled stock:
In some applications a hesitant feed can occur if the raise of the lettering prevents the sheet retarder from functioning normally. This can also occur with heavier stocks should they develop a curl when printed. Should this become an issue, the following steps can be performed:
- Run stock through image side down.
- Apply some weight to the stock for a period of time before it is to be run.
- Use the 8.5" and 11.0" weights on top of the stack.
Should stock still have feed issues call technical support at Martin Yale Industries, Inc. at 260-563-0641.
Should your machine need to be professionally serviced, Martin Yale Industries, Inc. can refer you to the nearest Factory Authorized Technician. Contact us at the phone number given above.
6.0 Accessory Function
Factory standard accessories include scoring wheels and perforator wheels. Each component uses its own cutting hub as an assembly. The components cannot be separated.
To engage the scoring roller, follow the instructions below:
- Loosen the 3/32" Allen set screw in the lower back up hub.
- Slide the scoring roller and hub to the appropriate location.
- Retighten the setscrew in the back up hub.
NOTE: The scoring roller does not contain a setscrew. This component should be free spinning.
To engage the perforator wheel, follow the instructions below:
- Loosen the 3/32" Allen set screw in the perforating wheel and in the backup hub.
- Slide components to the appropriate location. Retighten both setscrews.
NOTE: THE BACKUP HUBS ARE NOT INTENDED TO BE SEPARATED FROM THEIR UPPER COUNTER PART. DO NOT ATTEMPT TO SEPARATE THESE ITEMS.
NOTE: Positioning of the feed rollers to the scoring/perforating blade should be located at the left edge and right edge of stock being used. NOTE: OVERTIGHTENING OF SET SCREWS CAN CAUSE STRIPPING. WHEN TIGHTENING ACCES- SORIES, SCREWS SHOULD BE APPLIED 1/8-1/16 OF A TURN PAST SNUG.
Page 5 of 9

Text on page 6
7.0 Troubleshooting
Multiple Sheet Feeding:
- Set feed system per Section 5.1.
- If stock is glossy the feed wheels of the machine may have grip issues. This is a common issue with friction
- fed units. If one side is not glossy, run through with glossy side facing up.
Inaccurate Registration:
Set registration on unit per Section 5.0. Double-check the layout to make sure that the register marks are being utilized in the proper manner. Verify that locking knobs in the paper guides are tight. NOTE: DO NOT OVERTIGHTEN LOCKING KNOBS. Check o-rings on the unit for signs of wear and tear. Clean paper dust off component. Check the upper extreme left O-ring and the extreme lower right O-ring. Verify that the document is going under these on both sides. Readjust as necessary. If the document does not go under these on both sides it will cause the document to skew to one side.
Stacking Issues:
If business cards do not properly fall into slots:
- Slide the collection tray as the machine runs to fine - tune positioning.
- Make sure collection trays are not obstructed. They should hang freely from the exit side of the unit.
Scoring / Perforating Issues:
Scoring roller cutting stock: The solution to this is to humidify your stock. Typically only very dry material will do this.
Poor perforation or score:
- Check the nearness of the guide roller to the score or perforation wheel. If possible, position for better function to the extreme edges of the stock.
- Verify that the set screws in the accessories have been tightened (scoring roller does not use a setscrew).
Skewing:
- Most often occurs during the second cut (2" width) on business cards slitters (does not apply to the SP100). Check that paper guides are properly adjusted to give minimal side clearance on material and still allow stock to slide freely.
- In the event the machine is properly set and a slight skewing may still occur, loosen the setscrew (A) in both of the collars with O-rings and slide collars inward (B) until slight resistance is felt. Do not push collar into slitter blade (C), as this will affect slitting quality. Retighten setscrews (A) after relocation and before operation. See diagram at right. Moving O-ring collars usually requires some amount of trial and error. It should only be attempted after all the above recommendations have been exhausted.
7.1 Maintenance
Proper maintenance of your unit will prevent most situations that cause damage. Follow the steps below to maintain the unit.
- Once every 60 days, clean all paper dust from the unit.
- Once every 90 days, check the Phillips head screws in each sheet retarder and make sure they are tight.
- Periodically, check the power cord of the machine for frays and pinches. Replace cord should any damage be found.
- As needed, clean feed wheels on the unit with mild cleaner and a Scotch-Brite pad.
- Periodically clean the O-rings on the cutter shafts with a damp, soft cloth.
- In the event of blade removal during the life of the machine, a diagram of blade placement has been included for reassembly purposes. See Figure next page. CAUTION: Blade spacing and tension is extremely critical to the operation of any business card slitter. Only a qualified service technician should attempt blade removal/replacement.
Page 6 of 9

Text on page 7
BCS 410/412, SP100 Parts List
Item 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 15. 16. 17. 18. 19. 20. 21. 22. 24. 25. 26. 27. 29. 30.
Part No. W-ODT0019 M-S031092 W-ODT0015 W-IDT1119 M-S032046 M-S019033 W-ODT1123 W-ODT0016 W-ODT1124 M-S032007 W-ODT0014 W-ODT0013 W-ODT0010 W-ODT0012 M-S019033 M-S022132 M-S022130 M-S022015 M-S022131 M-S63751563 M-S025054 M-S025052 M-S030045 M-S021073 W-ODT0007 W-ODT0009 W-ODT0024
Description Adjustment Block Spring Sheet Separator Feed Bracket Thumb Screw Knob Stand Off Pressure Finger Adjust Bar Paper Support Knob Right Hand Guide Left Hand Guide Drive Cover Drive Cover Stand Off 15T Pulley 10T Pulley 12T Pulley 14T Pulley Pulley 20XL 125T Double Sided Belt 65T Double Sided Belt Bumpers Motor Rear Cover Rear Cover Receiver Tray
Item 31. 32. 33. 34. 37. 38. 39. 40. 41. 42. 43. 44. 45. 46. 47. 48. 49. 50. 51. 52. 53. 54. 55. 56. 57. 58.
Part No. W-ODT0023 W-ODT0021 W-ODT0020 W-ODT0001 W-ODT0004 W-ODT0017 M-S014029 W-ODT0115 M-ODT1105 M-S031091 M-O200134 M-S014030 W-ADT1114 M-S014031 M-O003076 M-O003082 W-ODT1109 W-ODT0018 M-O003080 M-O003079 M-O003083 WRA03085D W-ODT0107 M-S63751634 W-ODT0022 W-ODT0025
Description Receiver Base Form 10 Up Catch Tray 12 Up Catch Tray Housing Assembly Housing Assembly Slitter Shaft 3/8 Clip Bearing Tension Collar Blade Blade Spring ½" Set Collar ½ Clip Bearing Feed Roll Assembly 5/8 Clip Bearing Accessory Guide Roller Score Roller Back Up Groove Guide Roller Perf - Score Shaft Accessory Rubber Accessory Bushing Scoring Roller Perf Roller Spacer 24T Pulley Base End Plate
Page 7 of 9

Text on page 8
BCS 410/412, SP100 Wiring Diagram
Brown
PART No. DESCRIPTION QTY.
M-S037020110 V0Ltcord
M-S045237 Amp Bcs Cir. Breaker
/-S033053SWITCHON/OFF
- S021073 110 V.A.C. BCS MOTOR
Page 8 of 9

Text on page 9
2.000 000:2 10 UPFORMAT
10 UP FORMAT
12 UPFORMA1
12 UP FORMAT
Feed
Perf/Score Accesories
Martin Yale
I ndustries
251 Wedcor Avenue · Wabash, Indiana 46992 Phone (260) 563-0641 ·Fax (260) 563-4575 Website: www.martinyale.com
Email: info@martinyale.com M-S027122 1/11/07
Page 9 of 9 ยท End of manual
Quick start
- Set the machine on a tabletop with the power switch at 0 (off).
- Check each feed shelf to confirm the retarder tips are not touching the feed wheels.
- Remove the taped stack weights from the exit trays and make sure no weights are in the feed bins before the first run.
- Install the paper support and collection trays: the finished-card bin goes on the middle shelf, the large tray on the top or bottom.
- Turn the rocker switch to 1; the unit should start running.
- If needed, align the register marks on the layout sheet with the blade edges and set the paper guides to no more than 1/32" side play.
- Test with a neat stack of three sheets and adjust the retarder until one sheet feeds steadily.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| No power when switched on | Dead outlet or a tripped circuit breaker | Test the outlet with another device. If the breaker tripped, find and correct the machine bind, let it cool and push the breaker in to reset. Page 3 |
| Multiple sheets feeding | Feed system not set, or glossy stock reducing feed wheel grip | Reset the feed per the Proper Feeding section. If one side is not glossy, run with the glossy side facing up. Page 6 |
| Inaccurate registration | Registration not set, loose paper guide knobs, or worn/dusty O-rings | Reset registration, confirm the locking knobs are tight (do not overtighten), and check and clean the O-rings. Make sure the sheet goes under the outer O-rings on both sides. Page 6 |
| Cards don't fall into the collection slots | Tray position or an obstructed tray | Slide the collection tray while the machine runs to fine-tune, and make sure trays hang freely. Page 6 |
| Scoring roller cuts the stock | Very dry material | Humidify the stock. Page 6 |
| Poor perforation or score | Guide roller too far from the wheel, or loose set screws | Position the guide roller closer to the score or perf wheel, toward the edges of the stock, and tighten the accessory set screws. Page 6 |
| Cards skewing, usually on the 2" second cut | Paper guides not adjusted for minimal side clearance | Adjust the guides so stock slides freely with minimal side play. As a last resort, move the O-ring collars inward until slight resistance is felt. Page 6 |
| Hesitant feed with thermographic or curled stock | Raised lettering or curl prevents the retarder from working normally | Run stock image side down, weight it before running, and use the 8.5" and 11.0" weights on top of the stack. Page 5 |
Frequently asked questions
What paper weights can the BCS410 handle?
24# bond to 100# cover stock. See page 2.
How fast is the BCS410?
375 finished cards per minute (the BCS412 does 300). See page 2.
What sheet sizes does it accept?
Minimum 4 1/8" x 3 ½", maximum 8 ½" x 11". See page 2.
How do I check that my cards are cut square?
Divide a stack of cards in half, flip one half over and recombine. All edges should align; if not, the stock is skewing. See page 4.
What maintenance does it need?
Clean paper dust every 60 days, check the retarder screws every 90 days, clean the feed wheels with mild cleaner and a Scotch-Brite pad as needed, and wipe the O-rings with a damp cloth. See page 6.
