Martin Yale BT100 User Manual, page 1

Page 1 of 17

Martin Yale BT100 User Manual, page 2
Text on page 2

PRODUCT MANUAL

BT100

BA N NER TRIMME R

Please review this manual in its entirety before attempting to operate.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 2 of 17

Martin Yale BT100 User Manual, page 3
Text on page 3

TABLE OF CONTENTS

ASSEMBLY INSTRUCTIONS

Install Handle Holder........................................ 4

Install Cross Support........................................ 6

Install Deck Frame Assembly........................... 7

Install Banner Carrier....................................... 8

Install Clamp Handles...................................... 9

PARTS IDENTIFICATION .......................... 10

INSTRUCTIONS FOR USE

Preparing a Banner for Loading...................... 11

Loading Banner into Banner Carrier................ 11

Setting Paper Guides...................................... 12

Placing and Locking Blades............................ 13

Pre-Wind Collection Bar & Using Turn Handle... 13

Removing Cut Banner..................................... 14

CARE AND MAINTENANCE

Oiling Linear Bearings..................................... 15

REPLACEMENT PARTS ............................ 15

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 3 of 17

Martin Yale BT100 User Manual, page 4
Text on page 4

ASSEMBLY INSTRUCTIONS

TOOLS NEEDED: 3/32" ALLEN WRENCH

3/16" ALLEN WRENCH 7/16" WRENCH Tongue & Groove Pliers

  1. Unbox Components

INSTRUCTIONS: Unbox components and set aside.

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever Not Shown
  10. 6 - 10-32 x 1/2" Button Head Screw
  11. 2 - 1/4-20 x 2-1/2" Socket Head Screw
  12. 10 - 1/4-20 Nut
  13. 10 - 1/4" Internal Lock Washer
  14. 1 - Banner Carrier Fabric

Page 4 of 17

Martin Yale BT100 User Manual, page 5
Text on page 5
  1. Install Handle Holder

TOOLS NEEDED: 3/32" Allen Wrench

INSTRUCTIONS: Attach Handle Holder (8) to Right Stand Leg (4) with two 10-32 button head screws (11).

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever
  10. 10-32 x 1/2" Button Head Screw
  11. 1/4-20 x 2-1/2" Socket Head Screw
  12. 1/4-20 Nut
  13. 1/4" Internal Lock Washer
  14. Banner Carrier Fabric

Page 5 of 17

Martin Yale BT100 User Manual, page 6
Text on page 6
  1. Install Casters

TOOLS NEEDED: 7/16" Wrench Tongue & Groove Pliers

INSTRUCTIONS: Install Swivel Casters (7) by screwing threaded stem into nut on Left Stand Leg (3), tighten with a pair of Tongue & Groove Pliers. Install Rigid Casters (6) onto Right Stand Leg (4), secure with washer (14) and nut (13).

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever
  10. 10-32 x 1/2" Button Head Screw
  11. 1/4-20 x 2-1/2" Socket Head Screw
  12. 1/4-20 Nut
  13. 1/4" Internal Lock Washer
  14. Banner Carrier Fabric

Page 6 of 17

Martin Yale BT100 User Manual, page 7
Text on page 7
  1. Install Cross Support

TOOLS NEEDED: 3/16" Allen Wrench 7/16" Wrench

INSTRUCTIONS: Install Cross Support (2) by slipping the tabs on either end over each stand leg (3) & (4) until holes in tab line up with holes on the stand legs. Then insert a 1/4-20 screw (12) into each hole from the top and loosely secure with a washer (14) and nut (13). Movement is needed for step 5.

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever
  10. 10-32 x 1/2" Button Head Screw
  11. 1/4-20 x 2-1/2" Socket Head Screw
  12. 1/4-20 Nut
  13. 1/4" Internal Lock Washer
  14. Banner Carrier Fabric

Page 7 of 17

Martin Yale BT100 User Manual, page 8
Text on page 8
  1. Install Deck Frame Assembly

TOOLS NEEDED: 7/16" Wrench

INSTRUCTIONS: With two people, install Deck Frame (1) by angling the Deck Frame Assembly so that the four studs on the bottom of the unit can slide into the holes on one stand leg (3) or (4) first (ensure that the handle side is installed on the stand leg with the rigid casters). Then push in on the other stand leg (4) or (3). Lower the deck frame and release pressure from the stand leg to allow the studs to slide into the remaining holes. Secure with washer (14) and nut (13) on each stud. Then tighten fasteners from step 4.

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever
  10. 10-32 x 1/2" Button Head Screw
  11. 1/4-20 x 2-1/2" Socket Head Screw
  12. 1/4-20 Nut
  13. 1/4" Internal Lock Washer
  14. Banner Carrier Fabric

Page 8 of 17

Martin Yale BT100 User Manual, page 9
Text on page 9
  1. Install Banner Carrier

TOOLS NEEDED: 3/32" Allen Wrench

INSTRUCTIONS: Install Banner Carrier Fabric onto Banner Carrier Bars if not done. Slide a banner carrier bar in between tabs on stand legs (3) & (4) making sure that the unfinished side of the fabric is facing the rear of the machine. Line up the threaded holes on the banner carrier bar with the holes in the tabs. Then secure with a 10-32 screw (11) in each hole. Repeat for the rear bar.

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle
  8. Clamp Lever with Brass Tip
  9. Clamp Lever
  10. 10-32 x 1/2" Button Head Screw
  11. 1/4-20 x 2-1/2" Socket Head Screw
  12. 1/4-20 Nut
  13. 1/4" Internal Lock Washer
  14. Banner Carrier Fabric

Page 9 of 17

Martin Yale BT100 User Manual, page 10
Text on page 10
  1. Install Clamp Handles

INSTRUCTIONS: Install the Clamp Lever (10) into the right paper guide which comes pre-installed on the Deck Frame Assembly (1). The Clamp Levers with Brass Tip (9) need to be installed on the blade carriers which are also pre-installed on the deck frame.

COMPONENTS: 1. Deck Frame Assembly

  1. Cross Support
  2. Left Stand Leg
  3. Right Stand Leg
  4. Banner Carrier Bars
  5. Rigid Casters
  6. Swivel Casters
  7. Handle Holder & Handle

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

  1. Clamp Lever with Brass Tip
  2. Clamp Lever
  3. 10-32 x 1/2" Button Head Screw
  4. 1/4-20 x 2-1/2" Socket Head Screw
  5. 1/4-20 Nut
  6. 1/4" Internal Lock Washer
  7. Banner Carrier Fabric

Page 10 of 17

Martin Yale BT100 User Manual, page 11
Text on page 11

PARTS IDENTIFICATION

BT 1 0 0

B AN NERTRI MME R

Cutting Module with Retractable Blade

Cutting Module Clamp Lever

Channel Guide Locking Clamp Lever

Stationary Guide Channel

Attachment Clips (3)

Banner Carrier

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 11 of 17

Martin Yale BT100 User Manual, page 12
Text on page 12

INSTRUCTIONS FOR USE

  1. PREPARING A BANNER FOR LOADING

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Prepare the banner for loading by tightly and evenly rolling up the banner with the artwork facing outward.

  1. LOADING BANNER INTO BANNER CARRIER

While holding onto the leading edge, place the uncut banner into the banner carrier so that the rolled up portion is placed on the inside nearest the center of the trimmer unit.

Feed the leading edge of the uncut banner into the stationary channel guide first, making sure it remains square with the front and back position of the guide.

Page 12 of 17

Martin Yale BT100 User Manual, page 13
Text on page 13
  1. SETTING PAPER GUIDES

Then, slide the other mobile channel guide on the opposite side of the trimmer so that the corner of the banner feeds squarely into the guide.

To maintain a square cut along both sides of the banner, ensure that when positioning the banner into the channel guides, each side of the banner is flush against the edge of the guide. When the banner is in place, secure the mobile channel guide by hand tightening the orange clamp lever.

  1. SECURING BANNER

Evenly space the attachment clips along the width of your banner. Note: this placement may vary each time depending on the custom width of each banner. Secure the leading edge of the uncut banner with the 3 attachment clips by pulling back the edge of each clip with your finger just enough for the banner to slide underneath. Make sure that the banner is able to slide deep under the clip about one inch so that it does not inadvertently pull out while commencing the trimming process.

Page 13 of 17

Martin Yale BT100 User Manual, page 14
Text on page 14
  1. PLACING AND LOCKING BLADES

Slide each cutting module to the desired edges of the banner (cutting blade stays in retracted position until next step.) For banners printed with a full bleed, allow for at least 1/8" bleed on each side of the desired cut to ensure that the desired color is maintained throughout. The BT100 will accurately trim to within 1/8". Once the banner is set to the desired location, engage the blade by firmly pushing down on cutting module and tightening the screw. Note: The top of the leading edge of the banner may remain uncut as the cutting modules do not directly engage with the top edge of the banner. When printing the banner, allow for a few inches of excess on the top or bottom of the banner (depending on which side is the leading edge being fed into the trimmer).

  1. PRE-WIND COLLECTION BAR and USING TURN HANDLE

Hand turn the collection bar about 1-1/4 turns so that the banner completely engages in the clips, once the banner is engaged. Attach the supplied turn handle on the side of the trimmer machine and begin to cut the banner by rotating the handle slowly in a counter-clockwise direction.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 14 of 17

Martin Yale BT100 User Manual, page 15
Text on page 15
  1. REMOVING CUT BANNER

Disengage the cutting module by loosening the orange clamp lever. Once the banner has been trimmed, retract blades by loosening the orange clamp lever. Remove turn handle. Gently pull banner off of the collection bar by carefully releasing the banner from the banner clips. Trim the remaining 1-2" portion of the uncut border off the both sides of the leading edge. Note: To avoid the trimmer from potentially tipping over, pull the banner in a downward motion.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 15 of 17

Martin Yale BT100 User Manual, page 16
Text on page 16

CARE AND MAINTENANCE

REPLACING BLADES

Remove the two black thumb screws on top of the cutting module. Then use a Phillips screw driver to remove the screw holding the blade in place. Replace the blade and reassemble the cutting module. Note: for replacement blades, the cutting module uses a standard off-the-shelf utility blade.

OILING LINEAR BEARINGS

For optimum performance, ensure that the linear bearings located inside the cutting module are lubed on a periodic basis.

REPLACEMENT PARTS

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 16 of 17

Martin Yale BT100 User Manual, page 17

Page 17 of 17 ยท End of manual

Quick start

  1. Roll the banner tightly and evenly with the artwork facing out, and place it in the banner carrier with the roll toward the center.
  2. Feed the leading edge into the stationary channel guide, then slide the mobile guide against the other edge and lock it with the orange clamp lever.
  3. Space the three attachment clips across the leading edge and slide the banner about one inch under each clip.
  4. Slide each cutting module to the desired cut line (allow at least 1/8" bleed on full-bleed prints), push down to engage the blade and tighten.
  5. Hand turn the collection bar about 1-1/4 turns, attach the turn handle, and rotate it slowly counter-clockwise to cut.
  6. Loosen the clamp levers to retract the blades, remove the handle, pull the banner off downward, and trim the 1-2" uncut leading edge.

Troubleshooting

ProblemLikely causeFix (from the manual)
Top of the leading edge is left uncutThe cutting modules do not engage the top edge of the bannerPrint with a few inches of excess on the leading edge and trim the remaining 1-2" by hand. Page 14
Banner pulls out of the clips while trimmingBanner not slid far enough under the attachment clipsSlide the banner about one inch under each clip and pre-wind the collection bar about 1-1/4 turns. Page 13
Trimmer tips when removing the bannerPulling the banner the wrong wayPull the banner off in a downward motion. Page 15

Frequently asked questions

How accurately does the BT100 trim?

It trims accurately to within 1/8". Allow at least 1/8" bleed on each side of the cut for full-bleed banners (page 14).

What blades does the BT100 use?

The cutting module uses a standard off-the-shelf utility blade. Remove the two black thumb screws and the Phillips blade screw to replace it (page 16).

What tools are needed to assemble the BT100?

A 3/32" Allen wrench, 3/16" Allen wrench, 7/16" wrench and tongue and groove pliers. Two people are needed to install the deck frame (page 4, page 8).

What maintenance does it need?

Lubricate the linear bearings inside the cutting modules periodically (page 16).