Martin Yale CDS200 CD Inserter Slitter and Perforator Manual, page 1
Text on page 1

CDS200

TABLETOP CD TRAY LINER SLITTER

QUICK INSTRUCTIONS

INTRODUCTION

Thank you for selecting the Martin Yale Model CDS200 Tabletop CD Tray Liner Slitter. This liner slitter was designed for easy installation, set-up, and operation with minimal maintenance required. We recommend that you familiarize yourself with the Model CDS200 Tabletop CD Tray Liner Slitter by carefully reading this manual. Thorough understanding of this information will eliminate most operator-associated errors.

Functional Maximum Stock Size………………………………………………………………….9” X 12” Speed………………………………………………………………………approx. 4200 /Hour Load Capacity………………………………………………………………………….……5/8” Physical Machine Dimensions…………………………………………………15 ½”w X 6 ½”d X 11”h Machine Weight……………………………………………………………….……….31# Lbs. Electrical Power……………………………………………………………………..115V.A.C. 50-60Hz.

  • Shipping Weight Model CDS200 – 31 lbs

WARNING! Never connect power to the machine until you are ready to set up and operate the CD liner slitter. During set up, operation, and maintenance keep hands, hair, loose clothing, and jewelry away from all moving parts. Serious bodily injury could result. Service, or disassembly of letter opener should only be attempted with the power disconnected and locked out.

251 Wedcor Avenue Wabash, Indiana 46992 Ph# (260) 563-0641 Fax# (260) 563-4575 email: info@martinyale.com website: www.martinyale.com Made in U.S.A.

Page 1 of 4

Martin Yale CDS200 CD Inserter Slitter and Perforator Manual, page 2
Text on page 2

I. Set up from carton to table

  1. Unpack CD Tray Liner Slitter and accessories; place CD Tray Liner Slitter on a stable level surface near an electrical outlet. Install Paper Support
  2. Untape machine accessories and place aside.
  3. Install paper support as shown in Figure #1 and Figure #2.
  4. Install catch trays. Line up tabs and slots as shown in Figure #3. Let trays hang from slitter. Longer tray goes on lowest level, shorter tray goes on level above. Install Bottom tray first. See Figure #4.

Let Paper Support rest on bottom feed shelf after inserting tabs

Line tabs of exit trays up with slots on machine and “hang” exit trays from slitter

Install short tray on level above

Install longer exit tray on bottom first

Page 2 of 4

Martin Yale CDS200 CD Inserter Slitter and Perforator Manual, page 3
Text on page 3

A. Paper guide set up. Not all paper widths are necessarily equal from ream to ream and paper guide adjustment may be needed for each size. To adjust paper guides, follow the steps below:

1. Turn slitter off and unplug.

2. Slide a single sheet of stock into the appropriate feed shelf. First pass (3 cuts) goes on lower shelf; second pass (cut and perforate) goes on the shelf above. Registration marks on stock must be face up.

3. Push stock all the way in to the blades. Paper Guide

4. Check location of registration marks to Thumb Knobs blades. If they do not align, loosen both and move the paper guides with stock left or right until the registration marks (see Figure #6) align themselves with the cutter blades. You may need a flashlight to see the cutter blades from the feed side. Tighten paper guides down so that side-to-side movement of stock is no more than 1/64”. Paper guides too tight will result in inconsistent feeding; too loose will result in skewing and/or crooked cuts.

Align Registration Marks with Blades (See Inset)

Registration Marks (on Layout Sheets)

FIG.

DESCRIPTION

FIG.

DESCRIPTION

1 W-ODT0019

2 M-S031092

ADJUSTMENT BLOCK

TIMING PULLEY

SPRING

95T DBL SIDED BELT

3 W-ODT0015

4 W-IDT1119

SHEET SEPARATOR

755 RW BUMPERS

FEED BRACKET

BCS AC GEARMOT 110V

5 W-ODT0202

6 M-S019033

11" TOP PLATE FEMALE

22 W-ODT0020

CATCH TRAY 12 UP

STAND OFF

23 W-ODT0017

FEED SHAFT

7 W-ODT1123

8 W-ODT0016

PRESSURE FINGER

3/8 CLIP BEARING

ADJUSTMENT BAR

1/2 CLIP BEARING

9 W-ODT1124

10 M-S032007

PAPER SUPPORT

26 W-OGC0026

FEED ROLL ASSEMBLY

KNOB

5/8 CLIP BEARING

11 W-ODT0014

12 W-ODT0013

RIGHT HAND GUIDE

28 W-ODT0018

PERF/SLIT SHAFT

LEFT HAND GUIDE

29 W-ODT0107

THREADED SPACER

13 W-ODT0011

14 M-S019033

DRIVE COVER

30 W-ODT0022

BASE COVER

STAND OFF

31 W-OCD0002

REAR COVER

15T PULLEY

32 W-OCD0004

LINER CATCH TRAY

10T PULLEY

33 W-OCD0001

CDS FRAME

12T PULLEY

B. Retarder set-up. See Figure #7 for picture of retarder location. Retarder is raised or lowered by turning the retarder adjustment knob on side of machine as shown in Figure #8. Proceed as listed below.

1. Turn off and unplug machine.

2. Turn all retarder adjustment knobs 1 turn counter clockwise; you should see the paper retarder rise slightly.

3. Place a piece of stock between retarder and feed wheel. Slowly turn the appropriate retarder adjustment knob clockwise until a distinct drag is felt on the feed tire while the stock is moved in and out. Fine-tuning of the retarder can be accomplished by slightly turning the retarder knob while the slitter is running with stock in it. Note: Retarder should not touch feed roller.

Retarder should never contact the feed wheel at this point

Page 3 of 4

Martin Yale CDS200 CD Inserter Slitter and Perforator Manual, page 4
Text on page 4

C. Pressure Arm adjustment. See Figure #9 for pressure arm location and pressure arm adjustment Knob. If adjustment is needed, proceed as listed below:

1. Turn off and unplug machine.

2. Turn pressure arm adjustment knob clockwise to lower pressure arm and counter-clockwise to raise pressure arm. NOTE: Very little turning of the pressure arm adjustment knob is needed to result in a substantial change in pressure arm location. Typically only a slight turning of the pressure adjustment knob is needed to adjust the machine to the desired point.

3. Turn knob so that the pressure arm slightly drags a single piece of stock, but does not touch the feed wheel. See Figure #10. NOTE: If the pressure arm drags on the feed wheel, feed wheel damage will occur if extended operation without stock in place.

Pressure Arm Adjustment Knob

  1. Repeat with a single sheet of stock on the upper machine level. See Figure #12. Note that the full 8 ½” by 11” sheet goes on the lowest bin, the slit product of that bin then is run through the level above.

Loading 8 ½” X 11” Stock in lowest bin

Loading product of lowest bin into the bin above

Slight drag on stock at this point

A. Plug Slitter into a 115 V.A.C. outlet and turn it on (without stock). The machine should immediately begin to run. If slitter stalls for more than 5 seconds, check for:

1. Dead electrical outlet

2. Obstruction in blades

3. Tripped breaker; find source of machine bind and correct. Push in breaker to reset. Warning: These units contain rotating blades and other dangerous items. Do not remove any safety covers from the machine. Beware that loose jewelry, long hair and loose fitting clothes should be kept away from the unit at all times.

B. Run machine for a couple of minutes without stock to seat the blades.

1. Put a single sheet in the lowest shelf and turn machine ‘ON’. It should feed and slit. See Figure #11. NOTE: You may see oil residue on the first few pieces of stock. This is normal. Use unprinted stock to remove.

3. Once you are comfortable with the single sheet performance of card slitting, a stack of stock may be slit. WARNING: Only install stock into the slitter while it is ‘off’. Attempting to load stock while the slitter is running may result in injury or damage to the machine.

4. Turn slitter ‘ON’, it should feed and slit the stock one sheet at a time. If machine double feeds or hesitates, follow the steps below:

a. Paper guides too tight will result in hesitant feeds; try loosening paper guides slightly as outlined in Section III.

b. Retarder too loose or too tight will result in double or hesitant feeds. Slightly adjust retarder as outlined under retarder adjustment in Section III. Usually only a slight turning of the retarder adjustment knob is needed to allow the slitter to function.

c. The correct use of stack weights can significantly improve the feed of curled or otherwise difficult to feed stock, and also may improve straightness of feed if necessary (see Figure #13).

Correct use of stack weight on top of stack

A. Now that the slitter is set up, printed stock can start to be run through it with printed side facing up. Follow the steps as listed below. Please note that slitting tray liners require 2 passes through the machine. The 1st pass is done on the lowermost level; the product of that level is then placed on the level above where the liners are cut to their final size and perforated on both edges.

1. If stock goes as far as the blades and then stops, the retarder is slightly too wide. Slowly turn retarder knob clockwise while the machine is running until the stock goes through. NOTE: Turn the retarder no more than ¼ turn. Turning the retarder more than this may damage the feed wheel if making contact.

Page 4 of 4 ยท End of manual

Quick start

  1. Place the slitter on a stable, level surface near an outlet, then install the paper support and hang the catch trays (longer tray on the bottom level first, shorter tray above).
  2. With the machine off and unplugged, slide one sheet into the lower shelf with registration marks face up and adjust the paper guides until the marks line up with the blades; allow no more than 1/64" side-to-side play.
  3. Set the retarder: back each knob off one turn, then turn clockwise until you feel a distinct drag on a sheet. The retarder should never touch the feed wheel.
  4. Adjust the pressure arm so it lightly drags a single sheet without touching the feed wheel.
  5. Plug into a 115 V AC outlet, turn the machine on without stock and run it a couple of minutes to seat the blades.
  6. Load stock only with the machine off. Run full sheets on the lowest level first (3 cuts), then run that product on the level above to cut liners to final size and perforate both edges.

Troubleshooting

ProblemLikely causeFix (from the manual)
Slitter stalls for more than 5 seconds at start-upDead outlet, obstruction in the blades, or a tripped breakerCheck the outlet and blades; find and correct the source of the bind, then push in the breaker to reset. Page 4
Hesitant feedingPaper guides set too tightLoosen the paper guides slightly. Page 4
Double feeds or hesitant feedsRetarder too loose or too tightTurn the retarder adjustment knob slightly; usually only a small adjustment is needed. Page 4
Curled or difficult stock feeds poorly or crookedNo stack weight on the stackPlace a stack weight on top of the stack to improve feeding and straightness. Page 4
Stock goes as far as the blades and stopsRetarder gap slightly too wideWith the machine running, slowly turn the retarder knob clockwise until stock goes through, no more than 1/4 turn. Page 4
Skewing or crooked cutsPaper guides too looseRe-adjust the guides so side-to-side movement is no more than 1/64". Page 3
Oil residue on the first few sheetsNormal after setupRun unprinted stock to remove the residue. Page 4

Frequently asked questions

What size stock does the CDS200 accept?

The maximum stock size is 9" x 12", with a load capacity of 5/8" (page 1).

How fast is the CDS200?

It runs at approximately 4,200 sheets per hour on 115 V AC, 50-60 Hz power (page 1).

Why does it take two passes to make tray liners?

The first pass on the lowest level makes three cuts. The product of that level then goes on the level above, where liners are cut to final size and perforated on both edges (page 4).

How do I line up my printed sheets with the blades?

Insert a single sheet with registration marks face up, push it to the blades, then loosen the thumb knobs and move the paper guides until the marks align with the cutter blades (page 3).