Martin Yale P7200 RapidFold instruction manual, page 1: cover
Text on page 1

Martin Yale P7200 RapidFold Desktop Auto Folding Machine

Instruction Manual

Provided by MyBinding.com. Call us at 1-800-944-4573.

Page 1 of 5

Martin Yale P7200 manual, page 2: specifications, components diagram and safety warning
Text on page 2

RapidFold instruction manual

Model P7200 (110V), Model P720022 (220V)

Specifications

  • Folds 8.5" x 11" or A4 size paper
  • Creates four different folds
  • Operates at a speed of 4000 sheets/hr
  • Accepts 16–28 lb. bond paper (60–105 gsm)
  • Folds 1 sheet at a time automatically, or up to 3 sheets at a time manually

Your machine comes with the following components

  1. RapidFold folding machine
  2. Paper guides (2)
  3. Front fold table
  4. Back fold table
  5. Metal brackets (2)
  6. Exit tray connector set (3). Exit tray connectors contain 3 top plastic pieces, 3 bottom plastic pieces, and 6 connector screws.

Warning! Never connect power to the folder until you are ready to set up and operate the machine. During set up, operation, and maintenance keep hands, hair, loose clothing, and jewelry away from all moving parts. Serious bodily injury could result. Service or disassembly of the folder should only be attempted with the power disconnected.

Martin Yale Industries, Wabash, IN 46992. Phone (260) 563-0641. www.martinyale.com. Made in Taiwan.

Page 2 of 5

Martin Yale P7200 manual, page 3: assembly of the paper guides and exit tray, and aligning the paper guides
Text on page 3

Assembly

  1. Insert the paper guides into the paper tray as shown in Figure 1. You will need to remove the black plastic nuts and clear spacers from the guides. Once inserted, install the clear spacers on the paper guides and screw the nuts back onto the paper guides and tighten. The paper guides should now be attached to the machine as shown in Figure 2.
  2. To assemble the exit tray, you will need a #2 Phillips screwdriver, the 2 metal brackets, and the 3 exit tray connector sets (each set contains one top plastic piece, one bottom plastic piece, and two screws). Assemble each exit tray connector set onto the metal brackets as shown in Figure 3. Hint: it may be easier to assemble the middle connector set first. Position the front set near the front of the exit tray for better stacking.
  3. The assembled exit tray should fit underneath the machine (Figure 4). It does not snap into place; the weight of the machine will hold it in position. Push the tray so it is against the tabletop. Many users find it easier to attach the first connector to one metal part and screw it halfway together. The other metal portion may then be installed to the plastic connector and screwed together completely.
  4. Insert the plug into the back of the machine, and then into an electrical outlet.

Aligning the paper guides

Note: paper guide placement is a critical and often overlooked factor in machine set-up. Please follow the instructions below carefully to assure trouble-free paper feeding.

  1. Loosen the 4 plastic thumbscrews under the feed table (see Figure 1 for thumbscrew location) to loosen the paper guides.
  2. For standard U.S. 8 1/2" x 11" paper, move both paper guides in so that their inside edges align with the straight marks on the feed table denoted LS (see Figure 5). For A4 paper, align the outside edges of the paper guides with the straight marks denoted A4. Tighten both thumbscrews (do not over-tighten).
  3. Slide a single piece of paper between the paper guides and check for:
    1. Pinching: the paper should slide freely between the paper guides with a small amount of clearance to feed freely. Loosen the thumbscrews and adjust the paper guides if necessary. Setting the paper guides too tight will result in feed hesitation.
    2. Skewing: the paper should be exactly square to the feeding roller. Loosen the thumbscrews and adjust the paper guides if necessary.

Figure 6 (bottom view of an installed fold table): the front slots on the fold tables go around the fold table pins, and cutouts in the fold tables rest on top of the silver tie rods.

Page 3 of 5

Martin Yale P7200 manual, page 4: installing and adjusting the fold tables, fold types, double fold and half fold setup
Text on page 4

Fold tables

The front and back fold tables should come already inserted in the machine. If you need to remove them for jam removal, insert them back into the machine as shown in Figures 7 and 8.

  • Slots on the ends of both fold tables fit onto the 2 silver-colored pins inside the machine (Figure 6).
  • The fold tables should rest on top of the silver tie rods (Figure 6).
  • The tables should go into the machine open end first. Exception: when doing a half fold, the back fold table should go in closed end first (see Half fold below). Hint: many users find it easier to install the fold tables while looking at them from the bottom.

Adjusting the fold tables

The RapidFold (110 Volt version) comes factory preset to fold an 8 1/2" x 11" sheet to a letter fold appropriate for a standard business envelope. 230 Volt machines (UK and Europe) are factory preset to fold an A4 sheet to a letter fold.

Before setting the P7200 to a fold different from the factory setting, you must understand the different types of folds (Figure 9 shows the letter, half, Z-fold and double parallel folds and their icons). A half fold requires that only the first fold table be set and used. All other folds require that both fold tables be set up and used.

Double fold operation

All folding operations apart from the half fold place two folds in the stock, as in the typical letter fold or Z-fold. The second fold table must be in the double fold position (the position it is in as received). To create the different types of folds:

  1. Loosen both locking knobs on both fold tables to loosen the paper stops.
  2. Locate the icons on the fold table rulers for the type of fold you want.
  3. Move the paper stops to the arrows next to the desired icons. 8 1/2" x 11" paper (yellow icons) uses the inch scale on the left side of the rulers. A4 paper (blue icons) uses the metric scale on the right side of the rulers (Figure 10 shows a Z-fold setting for US Letter).
  4. Tighten the paper stop locking knobs to lock the paper stops into position.

Half fold

To set the machine for a half fold, take out the back fold table (lift up and pull it out of the machine), reverse it so the knobs face up, and re-insert it closed end first, knobs still facing up (Figure 11). Adjust the front fold table as described in step 3 above.

Page 4 of 5

Martin Yale P7200 manual, page 5: automatic feeding, hand feeding of sets, clearing paper jams and troubleshooting
Text on page 5

Automatic feeding of single sheets

  1. Square a stack of up to 50 sheets of paper by tapping it on all sides on a flat surface such as a table.
  2. Load the squared stack into the P7200 feed table. The top sheet should be in contact with the black feed tire. Note: the stack need only be pushed into the feed mechanism with a light touch. Jamming the stack into the folder with force will result in feeding problems. The paper is placed in the folder square, not fanned; the folder feeds the top sheet (Figures 12 and 13).
  3. Turn the folder on by pushing the "I" portion of the I-O-II rocker switch. Folding should begin. Note: use Martin Yale Static Eliminator (model 300) to remove static and improve machine performance, and Martin Yale Rubber Roller Cleaner (model 200) for better folding performance and longer roller life.

Hand feeding of sets

Mandatory when folding multiple-sheet sets of paper.

  1. To prevent jams, remove all paper from the paper tray before feeding sets by hand.
  2. For sets of up to 3 sheets (stapled or unstapled), first square the paper against a tabletop.
  3. Place the paper into the manual feed slot on the top of the machine (Figures 13 and 14). Do not put multiple-sheet sets in the feed table; a jam will result.
  4. Use the momentary-on "II" switch position to start folding. Hold the switch down until the folded paper exits the machine.
  5. Do not run the machine for long periods without paper in the paper tray; this could wear down the feed tire.

Hint: multiple-sheet sets may crease because of their thickness. Correct this by moving the 1st fold table stop out approximately 1/8". For example, if the 1st fold table were set at 7 3/8" for a letter fold, reset it to 7 1/2" for the multiple-sheet set.

Paper jams

  1. Unplug the machine. Check whether you can clear the jam by removing one of the fold tables.
  2. If you cannot remove the jam, use a flathead screwdriver to turn the folding rollers by hand through the access hole in the left side of the machine. The paper should eventually emerge.
  3. You may need to remove the top plastic cover to extract the jammed paper.

Troubleshooting

Problem: the paper jams in the machine

  1. If feeding by hand, make sure there is no paper in the paper tray.
  2. Re-align the paper guides and check the fold table settings.
  3. Check that the paper is within specifications (8 1/2" x 11" or A4, 16–28 lb. bond or 60–105 gsm).
  4. Remove the top cover and clean the rollers with Martin Yale Rubber Roller Cleaner (model 200).
  5. Use Martin Yale Static Eliminator (model 300) to remove static in the paper.

Problem: paper will not feed correctly

  1. Paper guides too tight or not parallel to each other: adjust them as described in Aligning the paper guides.
  2. If feeding by hand, make sure the paper is properly aligned before placing it in the slot.
  3. If feeding by hand, place the set in the slot before turning the machine on.
  4. Re-align the paper guides.
  5. Check that the paper is within specifications (8 1/2" x 11" or A4, 16–28 lb. bond or 60–105 gsm).
  6. The feed tire could be worn. Replace it.

Page 5 of 5 · End of manual

Quick start

  1. Fit the paper guides and the exit tray, then plug the folder in.
  2. Align the paper guides to the LS marks for 8.5" x 11" (or A4 marks). Paper should slide freely and sit square to the feed roller.
  3. Set both fold table paper stops to the arrows for the fold you want (yellow icons = inch scale, blue = A4). Half fold uses only the front table, with the back table reversed.
  4. Tap a stack of up to 50 sheets square and push it lightly against the black feed tire. Don't fan it.
  5. Press I on the rocker switch to fold. For sets of up to 3 sheets, empty the paper tray, use the manual feed slot and hold II.

Troubleshooting

ProblemLikely causeFix (from the manual)
Paper jams in the machinePaper in the tray while hand feeding, guides or fold tables set wrong, paper out of spec, dirty rollers or staticEmpty the tray when hand feeding, re-align the paper guides and check the fold tables, use 8.5" x 11" or A4 16–28 lb paper, clean the rollers with roller cleaner, use static eliminator. Page 5
Paper won't feed correctlyPaper guides too tight or not parallel, or a worn feed tireRe-align the paper guides so the sheet slides freely and square. Replace the feed tire if it's worn. Page 3
Feed hesitationPaper guides set too tightLoosen the thumbscrews and give the sheet a little clearance. Page 3
Creasing on multi-sheet setsExtra thickness of the setMove the 1st fold table stop out about 1/8" (e.g. 7 3/8" to 7 1/2" for a letter fold). Page 5
A jam won't clearPaper stuck between the folding rollersUnplug, remove a fold table, then turn the rollers with a flathead screwdriver through the access hole on the left side. Page 5

Frequently asked questions

What paper does the Martin Yale P7200 fold?

8.5" x 11" or A4 paper, 16–28 lb bond (60–105 gsm).

How fast is the P7200 RapidFold?

Up to 4,000 sheets per hour.

What folds can the P7200 make?

Four: letter, half, Z-fold and double parallel. Half fold uses only the front fold table, with the back table reversed (page 4).

Can the P7200 fold stapled sets?

Yes, sets of up to 3 sheets, stapled or unstapled, fed by hand through the manual feed slot using the "II" switch position (page 5).

How many sheets can I load in the feed tray?

Up to 50 sheets, squared and pushed in lightly against the feed tire (page 5).