Martin Yale W30 W36 Instructions, page 1

Page 1 of 3

Martin Yale W30 W36 Instructions, page 2
Text on page 2

Heavy-Duty Paper Trimmers

W30 PARTS LIST

Key Features and Benefits

  • Heavy-duty 3/4” thick wood base
  • Fully-hardened self-sharpening steel blades cut up to 20 sheets
  • Accurately cuts paper, matte board, cardboard, film, tissue, and textiles
  • Permanent 1/2” grid and dual rulers for proper paper alignment
  • Patented automatic blade latch locks with every cutting motion
  • Finger guard helps protect the entire blade length
  • Torsion spring counterbalances blade arm
  • Non-skid feet

WC36 PARTS LIST

Model Numbers

W30 – 30” cutting length WC36 – 36” cutting length

MADE IN USA

Page 2 of 3

Martin Yale W30 W36 Instructions, page 3
Text on page 3

Operating Instructions

Key Components

  • Hand Grip/Blade Arm/Blade Latch Assembly
  • Wood Base
  • Alignment Rulers
  • Finger Guard (note model WC36 has a automatic clamp in place

of the finger guard)

E – Paper Guide Ruler

Assembly Instructions

None – your trimmer is ready for use right out of the box

Automatic Safety Latch

The patented automatic blade latch is a key safety feature of this trimmer. It will lock with every complete cutting stroke, helping to eliminate forgetfulness. Remember to always push the blade arm down completely when you are finished cutting, to ensure that the latch activates. Never remove the latch for any reason.

  1. Place the trimmer on a flat, stable surface
  2. Release the blade latch, which is located on the hand grip (A)
  3. Lift the blade arm (A) up into cutting position
  4. Using the rulers or the 1/2” grid, align the paper to the proper position, pushing it up against the paper guide ruler (E).

CAUTION:

Keep hands and fingers behind the finger guard (D) at all times, away from the cutting blades

  1. While holding the paper down with your left hand (to make sure it stays in place), pull down the blade arm (A) to cut. Model WC36 has a clamp that will automatically activate to assist in holding the paper in place.
  2. Always make sure that the blade arm is completely down and locked when not in use.

Safety Information

Always ensure that the blade arm is fully pushed down, and that the blade latch is engaged, when not in use Never operate the trimmer without the finger guard in place Always keep clothing, jewelry, watches, and hair away from the cutting blade Keep out of the reach of children Do not carry the trimmer by the hand grip or the blade arm

For Best Cutting Performance

Use Trim-Ease Blade Lubricant for a smoother cut and to help preserve the life of the cutting blade. To order, send $4.00 per stick and a self-addressed, stamped envelope to the address below.

Customer Service

Telephone: Fax: Email: Internet: Address:

(260) 563-0641 (260) 563-4575 info@martinyale.com www.martinyale.com Martin Yale Industries, Inc. 251 Wedcor Avenue Wabash, IN 46992

Visit www.martinyale.com for more information on trimmers and other office products.

AUTOMATIC BLADE

SAFETY LATCH

Literature Part No. M-S027088

Page 3 of 3 · End of manual

Quick start

  1. No assembly needed. Place the trimmer on a flat, stable surface.
  2. Release the blade latch on the hand grip and lift the blade arm into cutting position.
  3. Align the paper using the rulers or 1/2" grid, pushed up against the paper guide ruler.
  4. Keep hands behind the finger guard. Hold the paper down with your left hand and pull the blade arm down to cut (the WC36 clamps automatically).
  5. Push the blade arm fully down after cutting so the automatic latch engages.

Troubleshooting

ProblemLikely causeFix (from the manual)
Blade arm will not liftThe blade latch is still engagedRelease the blade latch on the hand grip, then lift the blade arm into cutting position. Page 3
Blade latch does not lockThe blade arm was not pushed all the way downPush the blade arm down completely after cutting so the automatic latch activates. Never remove the latch. Page 3
Paper shifts during the cutPaper is not held or alignedAlign the paper using the rulers or 1/2 inch grid against the paper guide ruler (E) and hold it down with your left hand. Model WC36 has a clamp that holds the paper automatically. Page 3
Cut is rough or blade wears quicklyBlade is not lubricatedUse Trim-Ease Blade Lubricant for a smoother cut and longer blade life. Page 3
Trimmer moves while cuttingIt is not on a flat, stable surfacePlace the trimmer on a flat, stable surface. It has non-skid feet. Page 3
Finger guard is missingGuard was removed or is not in placeNever operate the trimmer without the finger guard in place, and keep hands and fingers behind it. Page 3

Frequently asked questions

How many sheets can the W30 or WC36 cut?

The self-sharpening steel blades cut up to 20 sheets (page 2).

What is the cutting length?

30" on the W30 and 36" on the WC36 (page 2).

What materials can it cut?

Paper, matte board, cardboard, film, tissue and textiles (page 2).

How does the safety latch work?

It locks automatically with every complete cutting stroke. Always push the blade arm all the way down when done, and never remove the latch. See page 3.

How do I keep the blade cutting smoothly?

Use Trim-Ease Blade Lubricant for a smoother cut and longer blade life (page 3).