MBM 1500S Manual, page 1

Page 1 of 52

MBM 1500S Manual, page 2

Page 2 of 52

MBM 1500S Manual, page 3
Text on page 3

Introduction

Thank you for purchasing UCHIDA Model “AeroFold” Air Suction Paper Folder. You should receive many years of reliable service from this machine. Compact and easy to use, “AeroFold” is sure to

streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual

thoroughly before using this machine.

Contents

Safety Instructions ......................................................................................4

(1) Specifications .........................................................................................7

(2) Accessories .............................................................................................8

(3) Part Names...........................................................................................10

(4) Designation and Functions of Operations Panel.............................. 11

(5) Setup .....................................................................................................12

(A) Setting of the Paper Ejection Table ..........................................................................................12

(B) Setting of Table 1......................................................................................................................13

(C) Setting of Table 2......................................................................................................................14

(D) Setting of the Auxiliary Paper Feed Table................................................................................16

(E) Connecting Power Cabler .........................................................................................................17

(6)Preparation of Paper ...........................................................................18

(7) Directions for use.................................................................................19

(A) Standard folding of standard-size paper..............................................................................19

(B) Standard Folding of Non-standard-size Paper..........................................................................26

(C) How to Use the Interval Function ............................................................................................27

(8) Adjustment...........................................................................................29

(A) Fine Adjustment .......................................................................................................................29

(D) Paper Height Adjustment .........................................................................................................38

(E) Standard of Suction Air and Paper Feed Table Height .............................................................39

(F) Separator Height Adjustment....................................................................................................40

G) Changing Location of Paper Ejection Roller.............................................................................40

(9) Memory ................................................................................................40

Page 3 of 52

MBM 1500S Manual, page 4
Text on page 4

(A) Fold Position Memory of Non-standard Papers.......................................................................40

(B) Fold Position Memory of Standard Papers...............................................................................41

(C) Clearing Memory......................................................................................................................42

(D) Clearing all the memorized patterns.........................................................................................42

(10) Check Lamps, Error Codes and Troubles......................................43

(11) Troubleshooting and Cleaning .........................................................46

(A) Troubleshooting of Paper jam ..................................................................................................46

(B) Cleaning of Sensors..................................................................................................................47

(C) Cleaning of Fold Roller and Paper Feed Belt...........................................................................48

Page 4 of 52

MBM 1500S Manual, page 5
Text on page 5

Safety Instructions

Definition of Symbols and Notes The following names and signs stand for possible dangers.

This symbol stands for immediate danger. Disregarding these instructions may cause severe injury.

This symbol stands for a potentially dangerous situation. Disregarding these instructions may lead to injuries or damage to property.

Danger

Make sure that the machine is electrically grounded to prevent electrical shock. Operate the machinery within reasonable voltage range. There is a risk of electrical shock or fire if a higher or lower voltage is used, or if an electric current is utilized with a frequency not within the range stated above. Do not place any object on top of this machine. There is a risk of electrical shock or fire if water or any foreign object enters the machine. Handle the power cord with care. There is a risk of electrical shock or fire if the cord is damaged, broken, or placed under a heavy object. Do not insert or remove the power plug when water is present. Do not remove the cover of this machine. There is a risk of an electrical shock. Do not reconfigure the electronics of this machine. There is a risk of an electrical shock or fire. Do not operate the machine if it is emitting smoke or a strange odor. Turn off the machine, unplug it from the outlet and contact your dealer. Do not operate the machine if the power cord is generating heat or emits a strange smell. Turn off the machine, unplug it from the outlet and contact your dealer. If a foreign object enters into the machine, turn off the power switch and unplug the power plug, then consult your dealer. In the event of a thunderstorm, unplug the machine.

Caution

Keep hair, clothing, and jewelry away from the machine while operating. Serious injury may result. Do not put the machine on an unstable or slanted surface. Doing so may cause the machine to drop or fall over, causing damage and possible injury. Store and operate the machine in a clean, dust-free environment with low humidity. Avoid areas with high moisture, extreme temperatures and excessive dust, as these conditions may cause machine failure or electrical shock. Operate the machine at the temperature of 5 degrees to 35 degrees C. Be sure to grasp the power cord by the plug when unplugging it from the electrical outlet. Not doing so may cause damage to the cord and possible electrical shock or fire. Be sure to pull the power plug out of the electric outlet before moving the machine. Not doing so may cause damage to the cord and possible electrical shock or fire. Unplug the power plug from the electrical outlet when this machine is not in use. The socket-outlet shall be installed near the equipment and shall be easily accessible.

Page 5 of 52

MBM 1500S Manual, page 6
Text on page 6

WARNING_

WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY.

Page 6 of 52

MBM 1500S Manual, page 7
Text on page 7

WARNING_2

WARNING

HAZARDOUS MOVING PARTS

KEEP FINGERS AND OTHER BODY PARTS AWAY.

Page 7 of 52

MBM 1500S Manual, page 8
Text on page 8
  1. Specifications

Model:

MBM 1500S Air Suction Folder

Paper sizes:

4.72 x 8.27 – 13.00 x 19.21 inch

Paper weight:

Bond 13.9 to 42.5 lbs (Bond 42.5 – 61.1 lbs for single fold with limited paper)

Paper quality:

Offset paper, Coated Paper

Folding patterns:

Single, Letter, Zigzag, Double Parallel, Fold-out and Gate* (*Gate is limited to certain papers)

Folding dimensions:

Maximum folding dimensions Table 1: 14.4 inch Table 2: 9.6 inch

Minimum folding dimensions Table 1: 2.1 inch Table 2: 2.1 inch Smallest adjustment increment: 0.004 inch

Paper feed system:

Belt Suction Feed system

Maximum capacity:

500 sheets, 20 lbs Bond

Folding speed:

2,500 to 15,000 sheets per hour (single fold using Letter size paper) Speed adjustable in 5 steps.

Control system:

Automatic setting by built-in microcomputer

Other functions:

Automatic paper size detector (Ledger, Legal and Letter) Four-digit counter with addition/subtraction modes Paper Jam detector/indicator Skew correction 18 memories for standard paper size (fine adjusted) 3 special memories for out of standard paper size

86dB, 20 lbs Bond , double parallel at the highest speed level 5

Power source:

100 thru 120 VAC, 2.6A/240W, 50/60Hz

Dimensions:

51.2 (W)×23.6 (D)×23.2 (H) inch 46.1 (W)×27.6 (D)×25.6 (H) inch

Weight:

Options:

Perforation unit Scoring unit

(in use) (in storage)

Shipping (Approx.): 198.4 lbs

Page 8 of 52

MBM 1500S Manual, page 9
Text on page 9
  1. Accessories

After un-boxing, make sure that the following accessories are present. Please contact your local dealer immediately if anything is missing.

Auxiliary paper feed table

Page 9 of 52

MBM 1500S Manual, page 10
Text on page 10

Auxiliary paper ejection table

Paper Spacer for Ledger and larger

Paper Spacer for Letter and smaller

Page 10 of 52

MBM 1500S Manual, page 11
Text on page 11
  1. Part Names

Top cover Left side cover Paper guide(L w/spring loaded & R ) Paper height detection sensor Auxiliary feed table Table 1 Control panel Paper feed table Door for the table 2 Right side cover L Stopper guide

Number ⑫ ⑬ ⑭ ⑮ ⑯ ⑰ ⑱ ⑲ ⑳ ∗

Name Skew adjustment knob Paper ejection table Paper ejection roller Auxiliary paper ejection table Power switch Paper ejection table socket Air adjustment knob Paper Spacer for Ledger and larger Paper Spacer for Letter and smaller Table 2

∗ Table 2 is set under the paper feed table in the machine, which you find when opening the door for the table 2, ⑨.

⑲ or ⑳ Paper Spacer on the paper feed table, make the paper stack flat.

Page 11 of 52

MBM 1500S Manual, page 12
Text on page 12
  1. Designation and Functions of Operations Panel

No. ①

Designation/Indication START/STOP key

Speed adjustment key Paper feed table up/down key Store key Memory 1/2/3 key Fold type key

Table 2 stopper move mode key Table 1 stopper move mode key Paper length input mode key Interval key Paper ejection roller move key

Starts and stops machine.

  1. Test folds two sheets without counting.
  2. Also test blow without folding, when pressed more than 2 seconds.

Adjusts speed. Moves up and down the paper feed shelf. Fold position after adjustment is stored. Three special fold types are stored. Six fold types can be input and stored. Shows the number of sheets, the position of the stopper pin of Table 1 and 2, and paper size. Clears the counter / resets after an error. Used for adjusting the position of the stopper of Table 1 and 2, the position of paper ejection roller, and paper length Used for inputting the number of sheets to be folded and the length of non-standard size paper Indicates when the position of stopper of Table 2 is adjusted. Indicates when the position of stopper of Table 1 is adjusted. Indicates when paper length is input Sets a certain time of interval to stop paper feed. Indicates when the position of the paper ejection roller is adjusted. Indicates when paper stock runs short, or the location of paper feed trouble. Indicates when cleaning of the FEED section (belt, roller) is necessary. It lights every after 10,000 peaces of paper are fed. For reset, turn on the machine holding down – key. You can disable this function when you turn up the machine keep pushing [single (Fold type)] key. You can activate this function again when you turn up the machine with[gate(Fold type)] key pushed. Indicates when the optional perforating unit is installed.

Page 12 of 52

MBM 1500S Manual, page 13
Text on page 13

(5) Setup

(A) Setting of the Paper Ejection Table

Install the paper ejection table to the main machine body.

Install the table by putting its hook on the guide pins at two

G uide p in

Make sure that the hooks are securely put on the guide pins.

Auxiliary paper ejection table

Install the auxiliary paper ejection table to the paper ejection

Join the connector of the paper ejection table to the machine.

Page 13 of 52

MBM 1500S Manual, page 14
Text on page 14
  1. Setting of Table 1

Slide Table 1 bracket (RH&LH) slowly to diagonal direction

along the guide of the main machine body.

Table 1 guide on the operator side

The Table 1 connector is set on the operator’s side. Give

caution not to damage the connector when installing the

Table 1 guide on the opposite side of the operator.

Install Table 1 to the main machine body securely and fix it

using the lock levers located on both sides. (Move top of the

lock lever to the arrow direction as shown in the right figure.)

Page 14 of 52

MBM 1500S Manual, page 15
Text on page 15
  1. Setting of Table 2

Make sure that no paper is loaded on the paper feed table, and

press the paper feed table Up and Down Key so as to raise the table

until it stops at the uppermost point.

For installing or removing table 2, do it after raising the paper

feed table up to the highest point using the paper feed table Up and

In case the paper feed table is located at any place other than

the lowermost point, if the paper feed table Up and Down Key is

Table up and down key

pressed, it moves down to the lowermost point. Therefore, press the

paper feed table Up and Down Key again to raise it to the

In case the paper feed table is located at the lowest point, if

the paper feed table Up and Down Key is pressed, the table moves

If the paper feed table Up and Down Key is pressed while the

paper feed table is in operation, the paper feed table stops motion.

Open the door for the table 2.

Place the Guide Bracket of Table 2 on the Table Guide 2 on both

Ta bl e2 G u i de

Page 15 of 52

MBM 1500S Manual, page 16
Text on page 16

Push Table 2 in the direction of arrow and along Table Guide 2.

Push Table 2 until it is securely locked.

Make sure that Table 2 is securely locked.

Insert the connector of Table 2.

Close the door for the table 2.

Page 16 of 52

MBM 1500S Manual, page 17
Text on page 17
  1. Setting of the Auxiliary Paper Feed Table

Have the Paper feed side table parallel and set the tip of metal fitting

of that between fixed pin No.1 and No.2

Fixed Pin No. 2

Fixed Pin No. 1

Put the Paper feed side table down as it is and catch the fixed pin

Put the Paper feed side table up diagonally, the tip of them should be

below fixed pin No.2 and pull down the paper feed side table.

Please check the tip of the paper feed side table catch the fixed pin

Page 17 of 52

MBM 1500S Manual, page 18
Text on page 18
  1. Connecting Power Cabler

Insert the power cable into inlet for machine and the other end to

Caution:

Do not use a power cable other than the one provided.

Page 18 of 52

MBM 1500S Manual, page 19
Text on page 19

(6)Preparation of Paper

Fan out the paper sufficiently.

If there is a sheet of paper whose edge

is bent or warped, it must be straightened.

Keep the stacking capacity.

Max. 500 sheets shee ts (20 ( 20 lbs Bond) Bond )

( 20 lbs Bond) Bond )

It should be noted that when paper as thick as 1.97 inch or more is stacked on the station, smooth collation will not be done. Also it may cause damages to the machine.

Page 19 of 52

MBM 1500S Manual, page 20
Text on page 20
  1. Directions for use

To start using this machine, following is described for paper size A3 and 80g/m2 offset paper with

Single Fold at medium speed 3. This introductory operation makes

the user to operate the machine

easier for applied applications.

As the user becomes familiar with the machine, it is recommended to use other paper sizes, paper

weights, folding patterns and different speeds.

  1. Standard folding of standard-size paper

Prepare approximately 200 sheets of Ledger, 11 x 17 inch, 20 lbs Bond. Paper corners must be

exactly 90 degree angles.

  1. Turn power switch on.
  2. Skew Adjustment Knob for Feed Table Make Paper Feed Table square to machine Front Wall by rotating Skew Adjustment Knob.

Center the scale indicator.

NOTE: Skew Adjustment Knob is used for the paper which weighs

more than 34.3 lbs Bond unless otherwise needed.

Skew Adjustment Knob for Feed Table

Feed Roller Direction Adjustment Dial

Rotate Feed Roller Direction Adjustment Dial and let Pin centered to the Scale.

NOTE: Feed Roller Direction Adjustment Dial is used for the paper which weighs less than 34.3 lbs Bond

unless otherwise needed. Use Skew Adj. Knob when Feed Roller Direction Adj. Dial is not effective.

Page 20 of 52

MBM 1500S Manual, page 21
Text on page 21
  1. Set sheets of paper on the paper Feed Table. By pressing Up and Down Key, lower the Feed Table before placing

When setting sheets of paper on the paper feed table, press the paper feed table Up and Down Key. In case the paper feed table is located at any place other then the lowest point, it moves down to the lowest point. Also, in case the paper feed table is located at the lowest point, if the paper feed table Up and Down Key is pressed, the table moves up. If the paper feed table Up and Down Key is pressed while the paper feed table is operating, the table stops.

Table up and down key

Note: In case of installing or removing table 2, do it after raising the paper feed table up to the highest point using the paper feed table Up and Down Key.

Skew Adjustment Knob for Feed Table

  1. Loosen the paper guide set screws and adjust the L and R paper guide to fit the width of the paper.
  2. Set the paper spacer matching to the size of paper on the paper feed table. (In this case Ledger Size)
  3. Neatly arrange paper and place it on the feed table.
  4. Adjust Paper Side Guides fit to the paper and tighten the Set Thumb Screw. Make sure that the Spring loaded

Paper Guide which is installed inner of the L Paper Guide

(opposite side from control panel) slightly push paper edge with its spring.

Front Wall to leave no gap.

Push paper stack against machine

Page 21 of 52

MBM 1500S Manual, page 22
Text on page 22
  1. Place L Stopper Guide at the back end of the paper stack.

Note: Make sure that there is no space among the paper, Machine Front Wall and the paper guides. Otherwise it may originate paper skew. If gap is observed due to incorrect cutting of paper etc., adjust it by the Skew Feed Table Adjustment Knob. .

  1. Press Single Fold Key and the Key lights.
  2. Select Speed at Medium (3).
  3. Select 3 rows for Suction Belt.
  4. Set Suction Strength Window at 4.
  5. Set Paper Feed Table Height Adjustment Knob
  6. Press Test Mode Key for more than 2 seconds until buzzer sounds.

Then air starts to blow without feeding paper and Paper Feed Table rises.

  1. Adjust Air Blow Control Knob so as that the top 7 to 10 sheets flies

in the air with stability/steadily and without sticking two

sheet together. Dial is set more or less at fine line (week blow)

as right picture for 20 lbs Bond paper.

Air Blow Control Knob

  1. Press Test Key again and two sheets come out with single fold.

NOTE: (1) By pressing Test Key during blow test mode, machine test folds and automatically goes out of

  1. Or, by pressing START/STOP Key, blow test mode ends.

Page 22 of 52

MBM 1500S Manual, page 23
Text on page 23

17. Check 2nd sheet to see if there is any skew.

(1) Skewed to the right.

(a) Loosen Thumb Screw and slightly turn Feed Roller Direction Adjustment Dial

counter-clockwise. Tighten Thumb Screw again.

  1. Press Test Key and check 2nd sheet if there is still any skew.
  2. Repeat (a) and (b) above, and any skew should be corrected by Feed Roller Direction

Upper side when paper was placed

Feed Roller Direction Adjustment Dial

(2) Skewed to the left

(a) Loosen Thumb Screw and slightly turn Feed Roller Direction Adjustment Dial clockwise.

Tighten Thumb Screw again.

  1. Press Test Key and check 2nd sheet if there is still any skew.
  2. Repeat (a) and (b) above and any skew should be corrected by Feed

Roller Direction Adjustment Dial.

Upper side when paper was placed

  1. After skew is corrected, make trial fold of 10 sheets and make sure that obviously apparent skew is not found for

2nd sheet till 10th sheet.

Note 1st sheet is not checked because it is folded before machine is in stabilized motion.

Page 23 of 52

MBM 1500S Manual, page 24
Text on page 24

Through above procedures, basic operation of the machine has been learnt. Now, we try in applied applications.

  1. Selection of fold type

One of the six folding types (Single, Double Parallel, Fold-out, Letter, Zigzag, and Gate) can be selected. Press the desired fold type key.

Example: When selecting the Single folding type, the button illuminates as shown in the right figure.

  1. Setting of the number of sheets of paper to be folded

When inputting the number of sheets of paper (preset counter):

Press the C Key to display “0” on the counter.

Input the value of necessary number using the numerical keys

from “1” to “1000”.

Then, the machine operates until the input value becomes “0”

If the value displayed on the counter is “0”, the machine

operates until there is no paper loaded on the paper feed shelf.

  1. Setting of the speed

When setting the speed:

The speed can be changed by using “H” key or “L” key.

The third lamp from the left (lamp in the middle) shows the

Note that the lamp further on the right side from the middle

shows the higher speed is set while the lamp further on the left

side shows the slower speed is set.

Set the speed according to the type of paper or fold.

Note:

When folding thicker paper, machine may not fold at lower

In this case, increase folding speed.

Page 24 of 52

MBM 1500S Manual, page 25
Text on page 25
  1. Press Test Mode Key for more than 2 seconds until buzzer sounds.

Then air starts to blow without feeding paper and Paper Feed Table rises.

  1. Adjust Air Blow Control Knob so as that the top 7 to 10 sheets flies

Air Blow Control Knob

in the air with stability/steadily and without sticking two

sheet together. Dial is set more or less at fine line (week blow)

as right picture for 20 lbs Bond paper.

Heavier the paper is the more air blow is needed.

  1. Press Test Key again and two sheets come out with single fold.

NOTE:

(1) By pressing Test Key during blow test mode, machine test folds and automatically goes out of

(2) Or, by pressing START/STOP Key, blow test mode ends.

16. Check 2nd sheet to see if there is any skew.

(1) Skewed to the right.

(a) Loosen Thumb Screw and slightly turn Feed Roller Direction Adjustment Dial

counter-clockwise. Tighten Thumb Screw again.

  1. Press Test Key and check 2nd sheet if there is still any skew.
  2. Repeat (a) and (b) above, and any skew should be corrected by Feed Roller Direction

Feed Roller Direction Adjustment Dial

Upper side when paper was placed

Page 25 of 52

MBM 1500S Manual, page 26
Text on page 26

(2) Skewed to the left

(a) Loosen Thumb Screw and slightly turn Feed Roller Direction Adjustment Dial clockwise.

Tighten Thumb Screw again.

  1. Press Test Key and check 2nd sheet if there is still any skew.
  2. Repeat (a) and (b) above and any skew should be corrected by Feed

Roller Direction Adjustment Dial.

Upper side when paper was placed

  1. After skew is corrected, make trial fold of 10 sheets and make sure that obviously apparent skew is not found for

2nd sheet till 10th sheet. Note 1st sheet is not checked because it is folded before machine is in stabilized motion.

Note:

When folding line does not match as desired, it is required to adjust the stopper position of Table 1 or Table 2.

(Refer (A) Fine Adjustment page 28 . )

When double feed occurs or paper is not fed, it is required to adjust air blow strength and paper height.

(Refer to (C) Air adjustment of page 37 or (D) Paper height adjustment of page 38)

Continuous folding:

When the START / STOP key is pressed, the machine

When the START / STOP key is pressed while the

machine is in operation, the machine will stop, but addition on

the counter will continuous.

If you wish to fold only the number of sheets desired,

use the subtraction counter function.

Page 26 of 52

MBM 1500S Manual, page 27
Text on page 27

(B) Standard Folding of Non-standard-size Paper

1. Selecting a fold type.

2. Input of the total paper length

Measure the paper length.

The arrow indicates the direction of paper feed.

Press Paper Length Input Mode Key.

Input the paper length using the numerical keys. The unit for input is mm. For example: Input paper length of 11.42 inch Press [1000] key 1 time. (Input unit of 10 inch) Press [100] key 1 time. (Input unit of 1 inch) Press [10] key 4 times. (Input unit of 0.1 inch) Press [1] key 2 times. (Input unit of 0.01 inch) Note: Units of numerical keys are one unit higher than the unit of length

The available input range is 13.0 to 19.25 inch.

After the length is set, press the Paper Length Input Mode

Key again to fix it. When any value other than standard

ones is input, the lamp flashes. To clear the input value,

press the Length Input Mode key and press the “C” key.

Max input for Table 1 is 366mm and Table 2 is 245mm.

FOLD-OUT

LETTER

ZIGZAG

GATE

Note:

Stopper position of Table1 and Tables2.

Also refer page 31.

SINGLE

DOUBLE

PARA LLEL

Table1 11.0 inch × 2/3 = 7.33 inch

Table2 11.0 mm× 1/3 = 3.67 inch

Page 27 of 52

MBM 1500S Manual, page 28
Text on page 28
  1. How to Use the Interval Function

After selecting a fold type,

Press the Interval key.

The lamp on the Interval Key illuminates.

The bar on the display right beside “SEC” flashes.

Using the numerical keys “1” or “10”, input a desired interval

time for intermittent operation.

∗ 1 to 99 seconds can be set as the interval time.

Press the Interval key again.

The bar on the display right beside “SET” flashes.

Using the numerical keys “1”, “10” or “100”, input a desired

number of sheets of paper to be folded for each interval.

∗ 1 to 999 sheets can be set for interval operation.

Press the Interval key again.

Then, the lamp on the Interval key flashes indicating the function is

Press the TEST key or START key to start paper folding. (When

pressing the TEST key first, then the counter function is not effective,

i.e, test sheets are not counted.)

∗ How to clear Interval Mode

Press the Interval Key and press the Clear Key or input “0”. Then, the interval function is cleared.

Page 28 of 52

MBM 1500S Manual, page 29
Text on page 29

Example:

How to set 8 seconds as interval time and 50 sheets fold as number of sheets for interval operation.

By this setting, the machine will stop for 8 seconds after folding 50 sheets, and start folding again automatically.

How to set:

Press the Interval key.

The bar beside “SEC” flashes. Using the numerical key, input “8”.

Press the Interval key.

The bar right beside “SET” flashes. Using the numeral key, input “50”.

Press the Interval key. The lamp on the Interval key flashes.

Set the speed according to the paper quality and fold type.

After setting, press the TEST key or START key to start folding.

In case of making preset number of folds with the Interval function is set,

input the desired preset number while the lamp on the Interval key is f lashing.

Then, the machine stops after the preset number of sheets of paper are processed.

Incidentally, when the dot below the units digit is lit, it shows

that the preset value is input and valid.

When it is not lit, it is not valid and the machine continues to process

until there is no paper loaded on the paper feed shelf.

Page 29 of 52

MBM 1500S Manual, page 30
Text on page 30
  1. Adjustment

Adjusting Table 1 or Table 2

Select the Stopper Move Mode key (Table 1or 2). The

lamp of the selected Stopper Move Mode key illuminates.

The present stopper position is shown on the [Counter].

In case of standard-size paper, the stopper moves automatically to

Table1 stopper move mode key

Table2 stopper move mode key

the suitable position according to the paper size and fold type.

Apply this adjustment when fine adjustment is in need for

Values input manually return to standard values if any one

of other fold type keys is pressed.

Press the +/- key and move the stopper to the desired position.

The value displayed to the [Counter] shows the position of the

Example: When display of the [Counter] is 11.38, the stopper

position is 11.38 inch.

The position can be moved based on a unit of 0.003 inch.

Note indicator shows lowest of 2nd digits from decimal point.

Press the Stopper Move Mode key (Table 1 or 2) again.

The lamp on the selected Stopper Move Mode key flashes.

Regarding the adjustment, refer to the table of page 31.

The length of the arrow for each fold type is set based on the

stopper position of Table 1 or 2.

Example, In case of Double Parallel,

Table 1: Fold a half of the overall length

Table 2: Fold one fourth of the overall length

Note: To prevent damage to the Interceptor Push Bar at Stopper of Table 1, it does not come into contact with

Interceptor when stopper is moved by manual mode to avoid enforced pushing.

With automatic mode only, it comes to contact with Interceptor to make by-pass the Table 1.

Page 30 of 52

MBM 1500S Manual, page 31

Page 31 of 52

MBM 1500S Manual, page 32
Text on page 32

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(Less than 34.31 lbs Bond)

(More than 34.31 lbs Bond or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really needed.

How stacked and folded

Bold line indicates leading

feed edge when paper is place

Shadow indicates upper surface when

paper is on feed tray

Page 32 of 52

MBM 1500S Manual, page 33
Text on page 33

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(Less than 34.31 lbs Bond)

(More than 34.31 lbs Bond or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really re ally needed.

Page 33 of 52

MBM 1500S Manual, page 34
Text on page 34

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(More than 34.31 lbs Bond or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

(Less than 34.31 lbs Bond)

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really needed.

How stacked and folded

Page 34 of 52

MBM 1500S Manual, page 35
Text on page 35

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(More than 34.31 lbs Bond or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

(Less than 34.31 lbs Bond)

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really needed.

How stacked and folded

Page 35 of 52

MBM 1500S Manual, page 36
Text on page 36

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(More than 34.31 lbs Bond or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

(Less than 34.31 lbs Bond)

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really needed.

How stacked and folded

Page 36 of 52

MBM 1500S Manual, page 37
Text on page 37

Bold line indicates leading edge when paper is place on feed try.

Skew Adjustment by folding pattern

Shadow indicates upper surface when paper is on feed tray.

Turn Metallic Thumb Screw

Turn Metallic Thumb Screw

Counterclockwise ( - )

Clockwise ( + )

(Less than 34.31 lbs Bond)

(More than 34.31 lbs or

Feed Roller Direct. Adj. Dial is not

Clockwise ( - )

Counterclockwise ( + )

NOTE: Do not use, at the same time, Feed Roller Direction Dial and Skew Adjustment

Knob unless really needed.

How stacked and folded

Page 37 of 52

MBM 1500S Manual, page 38
Text on page 38

[Air Blow Strength Adjustment]

The air blow strength can be adjusted

by turning the air adjustment knob from low, per finer line, to high, per thicker line.

General information: When double feed occurs, turn the air adjustment knob

towards lower position slightly. When paper is not fed, turn the air adjustment knob

towards higher position slightly .

Note: Do not change position of Air Adjustment Knob extremely

From the original position.

  1. Press Test Mode Key for more than 2 seconds until buzzer sounds.

Then air starts to blow without feeding paper and Paper Feed Table Rises.

  1. Adjust Air Blow Control Knob so as that the top 7 to 10 sheets flies

in the air with stability/steadily and without sticking two

sheet together. Dial is set more or less at fine line (week blow)

Air Blow Control Knob

  1. Press Test Key again and two sheets come out with single fold.

NOTE:

  1. By pressing Test Key during blow test mode, machine test folds and automatically goes out of
  2. Or, by pressing START/STOP Key, blow test mode ends.

Page 38 of 52

MBM 1500S Manual, page 39
Text on page 39

[Adjustment of Suction Air Strength]

When using thin papers like copy paper, double feed may tend to occur with stronger suction power.

Set Suction Strength Window at 4, i.e., opened fully.

Refer (E) at page 39.

The position of No. 0 is the closed condition of window, i.e., strongest suction by belt.

Suction Belt in effect can be switched between 3 rows and 2 rows, stronger and weaker suction respectfully.

Normally, 3 rows are used.

Suction Belt Control 3 or 2 rows

  1. Paper Height Adjustment

Adjust paper height by opening the top cover.

Paper Feed Table Height Adjustment Knob

In case of adjusting the position of paper height according to the paper quality, loosen the paper

feed table height adjustment knob and while holding the knob, set the point to “H”, “M” or “L”. Recommended Position : Set to “H” side when paper cannot be sucked.

Set to “L” side when double feeding frequently occurs.

Paper Feed Table Height

Page 39 of 52

MBM 1500S Manual, page 40
Text on page 40
  1. Standard of Suction Air and Paper Feed Table Height

Adjustment of suction air and paper feed table height depend on paper quality, print condition or other environment. So

adjust them by referring to the following table as approximate guidance.

Blow Air (Air Adj.

Paper Feed Table Height

70.9 lbs Coated Paper

86.5 lbs Coated Paper

106.1 lbs Coated Paper

70.9 lbs Coated Paper

86.5 lbs Coated Paper

106.1 lbs Coated paper

Wea We a kest

Refer Air Blow Adjustment

Test Blow is always

Air Blow Control Knob

effective tool for adjustment.

  1. Offset Paper

Suction Strength Window Opening

Suction Suc tion Belt Row Control

Less than 17 lbs Bond

17 thru 22 lbs Bond

Weight ( lbs )

  1. Coated Paper

Weight ( lbs )

Suction Strength Window Opening

Less than 27.9 lbs Bond

3R (2R in case of double feed)

Over 27.9 lbs Bond Bon d

Suction Belt Control 3 or 2 rows

Do one of followings and see how it works. Do not make two adjustments at one time.

Suction Air is too strong

Frequent Empty Feed

Open Suction Window for one graduation

Suction Air is too weak

Close Suction Window for one graduation

Top Paper Height, i.e., Paper Feed Table Height is too high

Top Paper Height, i.e., Paper Feed Table Height is too low.

Page 40 of 52

MBM 1500S Manual, page 41
Text on page 41
  1. Separator Height Adjustment

When adjusting the separator height, turn the separator adjustment knob using a flathead screwdriver

andadjust the height so that the tip of the separator rubber touches the paper feed belt.

If empty feed frequently occurs when thick paper is used, open about a 0.5mm space between the paper feed belt

and separator rubber. Use several sheets of paper to be used for filler gauge.

Bottom Line of Paper Feed

Separator Height Adjustment Knob

By turning the Separator Height Adjustment Knob clockwise, the separator raises to direction of paper feed belt. By

turning the Separator Adjustment Knob counterclockwise, the separator comes down to opposite direction of paper feed

  1. Changing Location of Paper Ejection Roller

Roller automatically sets at the preset positon as long as

Paper ejection Roller move key

paper size is standard norm.

In case of out of standard norm paper, press Paper Ejection Roller Move Key.

By pressing + or - Key, move the Roller and position where roller effectively

Works for specific folds. After position is selected, press Paper Ejection Roller

Depending folding speed and pattern, the Roller need to be relocated.

Smaller numeral shows location of Roller closer to machine body.

(9) Memory

(A) Fold Position Memory of Non-standard Papers

Memory of Non-standard folds can be input with the

memory 1/2/3 keys and the fold type keys.

The positions of the stoppers of the Table 1 and 2, position

of the ejection roller, and folding speed are all together saved

Page 41 of 52

MBM 1500S Manual, page 42
Text on page 42

Select the Memory Key in which the fold will be input. Press the Store Key and release immediately when you hear a beep sounds.

The lamp of the key in which the fold has been memorized

will flash. Memory remains storing specific setting

Even main Power Switch is turned off, i.e., when Power

Switch is turned on again, memorized pattern can be used

  1. Fold Position Memory of Standard Papers

When folding line(s) is not as desired for standard paper, the

fold position after adjustment can be stored to the Fold Type

Memory of 18 kinds of setting is available as follows:

18 kinds of papers (Ledger, Legal and Letter) × 6 kinds of

= 18 kinds of settings

Note: For each folding patter or one Memory Key, one

Each folding pattern can be stored.

Positions of stoppers of the Table 1 and 2, position of the

ejection roller, and folding speed are all saved in memory.

After adjustment of fold position folding line(s), press the Store Key. (Regarding the adjustment method, refer to Adjusting Table 1 or Table 2 of Page 26.)

Press Store Key and release immediately when you hear a beep sounds.

The lamp of the key in which the fold has been memorized

Page 42 of 52

MBM 1500S Manual, page 43
Text on page 43

Clear the storage input in the memory 1/2/3 keys and the fold type keys

Press first a desired Memory 1/2/3 Key or Fold Type Key being stored first and then keep pressing the C Key. Release immediately the C Key when you hear a beep sound. The lamp of the key in which the storage has been cancelled will light.

Note:

The lamp of the key in which the fold pattern is stored

  1. Clearing all the memorized patterns

Turn off the power and while pressing the C Key, turn on the power.

Note:

All the stored pattern including custom fold you memorized is

cleared. No chance to recall after cleared.

Page 43 of 52

MBM 1500S Manual, page 44
Text on page 44
  1. Check Lamps, Error Codes and Troubles

If Check lamp (1) is flashing it may indicate:

PERFO. CLEANING

  1. The paper feed shelf does not work.
  2. Failure of the paper height sensor

5 ) Excess loading of paper

PERFO. CLEANING

If Check lamp (2) is flashing it may indicate:

  1. Improper setting of Table 1
  2. Stopper lock of Table 1

PERFO. CLEANING

If Check lamp (3) is flashing it may indicate:

  1. The electric plug of Table 2 is not inserted
  2. Stopper lock of Table 2

PERFO. CLEANING

If Check lamp (4) is flashing it may indicate:

Page 44 of 52

MBM 1500S Manual, page 45
Text on page 45

PERFO. CLEANING

If Check lamp (5) is flashing it may indicate:

  1. The electric plug of the paper ejection unit is not inserted
  2. Ejected paper is full
  3. Ejected paper jam
  4. Paper ejection sensor is dirty dust or ink

PERFO. CLEANING

If Check lamp (6) is lit, it may indicate:

If Check lamp (7) is lit, it may indicate:

It lights after every 10,000 sheets of paper folded. ・ For reset, turn on the machine while pressing – Key. ・ You can disable this function when you turn on the machine keep pushing [single (Fold type)] key. ・ You can activate this function again when you turn on the

machine with[gate(Fold type)] key pushed.

PERFO. CLEANING

Clean the belt as frequently as needed depend on the printing condition and paper quality before the cleaning lamp is lit. Regarding the cleaning method, refer to Cleaning of Sensors of page 47 and Cleaning of Fold Roller/Paper Feed Belt of Page 48.

Note:

If paper is loaded immediately after printing, problems such as jamming, double feed, slipping, and wrinkling may occur. Make sure that the printing ink is completely dry, statics are gone and paper is well fanned out before loading. If the machine is placed in the vicinity of a fluorescent lamp and it operates irregularly, the paper size detection sensor may not be functioning properly because of light from the fluorescent lamp. In such a case, place the machine farther from the fluorescent lamp.

Page 45 of 52

MBM 1500S Manual, page 46
Text on page 46

For each error symptom, the following error code will be displayed.

Neither Table 1 nor the perforating/scoring unit is installed to the position of Table 1 unit.

Paper left in the paper ejection sensor unit, or the paper ejection sensor is dirty.

Excess loading of paper

Sensors require cleaning or rollers require cleaning.

Paper ejection table connector is not connected.

Table 2 is not installed

Remove the paper ejection table to use perforator unit.

The door of the Table 2 is open, or the top cover is open

Paper left in the paper feed sensor unit, or the paper feed sensor is dirty.

Failure of the paper height sensor.

Failure of the feed table up and down motor

Failure of the main motor, or the encoder is dirty

The paper ejection roller is locked, or the motor is disconnected, or the home position

micro SW for ejection roller is disconnected or dislocated.

The table 1 stopper is locked, or the motor is disconnected, or the sensor is disconnected.

The table 2 stopper is locked, or the motor is disconnected, or the sensor is disconnected.

Note: To clear Error Code, press C Key after cause of trouble is eliminated.

Page 46 of 52

MBM 1500S Manual, page 47
Text on page 47
  1. Troubleshooting and Cleaning

CUTION: Make sure to disconnect power cable before starting the troubleshooting.

  1. Troubleshooting of Paper jam

Remove the Table-1 and remove the paper or pieces of paper.

Open the table-2 door, remove the Table-2 and remove the paper or torn pieces of paper.

When paper jammed using less than 27.9 lbs Bond paper, eject jammed paper by force as follows:

(In case paper cannot be ejected by this method, remove jammed paper manually per the above steps.)

  1. By pressing the Plus Key for a while, the motor stats to rotate

and paper in the folding rollers is ejected.

  1. By pressing the Plus Key further, the fold stopper moves

towards the closest position of folding rollers and jammed paper

in the fold table is ejected.

Page 47 of 52

MBM 1500S Manual, page 48
Text on page 48
  1. Cleaning of Sensors

Excersize cleaning each sensor periodically.

  1. Open the top cover and remove paper powder or dust by cotton swab, etc. from the window

Circled position as shown in the following figure.

  1. Clean the paper eject sensor (circled position as shown in the following figure) by cotton Q-tips, etc.

(The paper eject sensor is emitter/receiver photo cells.

Clean both upper and lower photo cells.

lower photo cell tends to get dust accumulated.

  1. Clean the paper detection sensor by Q-tips. Locations of photocell on the Paper Feed Table are circled.

Page 48 of 52

MBM 1500S Manual, page 49
Text on page 49
  1. Cleaning of Fold Roller and Paper Feed Belt

When paper feed slips, folding line does not match as desired, wrinkled paper or inner paper jam occur

frequently, it may be caused from paper dust or ink accumulation.

Clean the fold roller as shown in the below figures.

Open the top cover, remove the Table 1 and clean each Folding Roller and Paper Feed Belt.

To clean Rollers located inside machine, r emove paper stack on the Paper Feed Table and move the Paper Feed

Table to the highest position.

Open Table-2 cover and remove the Table 2. Clean the folding roller installed in the depth of machine body.

Open the top cover and clean the paper feed belt.

Page 49 of 52

MBM 1500S Manual, page 50

Page 50 of 52

MBM 1500S Manual, page 51

Page 51 of 52

MBM 1500S Manual, page 52

Page 52 of 52 ยท End of manual

Quick start

  1. Prepare paper: For the first run, use approximately 200 sheets of Ledger, 11 x 17 inch, 20 lbs Bond. Paper corners must be exactly 90 degree angles.
  2. Power on and square the table: Turn the power switch on and square the paper feed table to the front wall with the skew adjustment knob.
  3. Load the feed table: Press the paper feed table Up and Down key to lower the table. Adjust the L and R paper guides to the paper width, place the paper neatly and push the stack against the front wall.
  4. Test fold: Press the Test key and check the 2nd sheet for skew. Adjust the Feed Roller Direction Adjustment Dial if needed.
  5. Fold: Press START/STOP to fold continuously. Use the subtraction counter function to fold only the number of sheets you want.

Troubleshooting

ProblemLikely causeFix (from the manual)
Double feed occursAir blow is too strongTurn the air adjustment knob slightly towards the lower position. Page 38
Paper is not fedAir blow is too weakTurn the air adjustment knob slightly towards the higher position. Page 38
Folded sheets are skewed to the leftFeed roller direction needs adjustingLoosen the thumb screw, turn the Feed Roller Direction Adjustment Dial slightly clockwise, tighten the screw and test again. Page 26
Fold line does not match as desiredStopper position of Table 1 or Table 2 is offAdjust the stopper position of Table 1 or Table 2. Page 26
Paper feed slips, paper wrinkles or inner paper jams occur oftenPaper dust or ink has built up on the fold roller or paper feed beltClean the fold roller and paper feed belt. Page 49
Cleaning lamp is litThe feed section (belt, roller) needs cleaning; the lamp lights after every 10,000 sheetsClean the belt and rollers. To reset, turn on the machine while pressing the minus key. Page 12

Frequently asked questions

What does the Test key do?

The START/STOP and Test keys control the machine. Test folds two sheets without counting, and pressing it more than 2 seconds tests the blow without folding. See page 12.

How do I raise or lower the paper feed table?

Press the paper feed table Up and Down key. Lower the table before placing paper, and raise it to the highest point before installing or removing Table 2. See page 21.

How do I check the air blow?

Press the Test key for more than 2 seconds until the buzzer sounds, then adjust the air blow control knob so the top 7 to 10 sheets float steadily without sticking together. See page 38.

How often does the machine need cleaning?

The cleaning lamp lights after every 10,000 sheets, but clean the belt as often as printing conditions and paper quality require. See page 45.