

Page 1 of 57

Text on page 2
OPERATION MANUAL
MBM Air Suction Folder
Model 1800S
Page 2 of 57

Text on page 3
Introduction
Thank you for purchasing MBM Model 1800S Air Suction Paper Folder. You should receive many years of reliable service from this machine. Compact and easy to use, 1800S Folder is sure to streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual thoroughly before using this machine.
Contents
Safety Instructions ........................................................................................................................... 4
1. Specifications ............................................................................................................................ 7
2. Accessories ............................................................................................................................... 8
3. Part Names .............................................................................................................................. 10
4. Designation and Functions of Operations Panel ..................................................................... 12
5. Setup after opening transport packing .................................................................................... 13
1) Setting of the Paper Ejection Table ............................................................................. 13
2) Setting of Table 1 ........................................................................................................ 14
3) Setting of Table 2 ........................................................................................................ 15
4) Setting of the Auxiliary Paper Feed Table .................................................................. 17
5) Connecting Power Cable ............................................................................................. 18
6) Turn on the Power Switch. .......................................................................................... 19
6. Preparation of Paper ............................................................................................................... 20
7. Initial setting ........................................................................................................................... 21
1) Prepare 200 sheets of Ledger(11x17”), 24lbs,Bond Paper ......................................... 21
2) Turn on Folding Machine ............................................................................................ 21 3)-6) Set up paper on Feed Table ............................................................................... 21-22
7) Leave no gap between Paper Leading Edge and Machine's Front Paper Stopper Wall ............................................................................................ 22
8) Skew Correction is done by two methods ................................................................... 23
(a) By Feed Angle Adjustment Dial (Drum-Feed-Roller) .................................... 23
(b) By Skew Adjustment Knob at Feed Table ...................................................... 23
9) Set L Stopper at the rear end of the Paper ................................................................... 23
10) Close the Top Cover. ................................................................................................. 23
11) Trial Air Blow and Suction ........................................................................................ 24
(a) Air Blow Strength Adjustment for sheet separation........................................ 24
(b) Paper Floating Height Adjustment relative to Suction Belt ............................ 25
(c) Adjustment of Suction Air Strength ................................................................ 25
(d) Approximate Guidance of Suction Air and Paper Feed Table Height ............ 26
12) Selection of Folding Pattern ...................................................................................... 27
13) Selection of Folding Speed ........................................................................................ 27
14) Setting Speed ............................................................................................................. 27
15) Test Folding ............................................................................................................... 27
Page 3 of 57

Text on page 4
16) Other Control and Functions ..................................................................................... 28
(a) Paper Ejection Roller ..................................................................................... 28
(b) How to use Interval Function ................................................................... 28-29
(c) Double Feed Detection or No-Detection ........................................................ 29
8. Standard folding of standard-size paper ................................................................................. 30
1) Selection of Folding Pattern ........................................................................................ 30 2)-3) Select Folding and Set Speed ................................................................................. 30
4) Set number of sheets to fold ........................................................................................ 30 (a), (b) Count Down and Count Up ...................................................................... 30
5) Start Folding ................................................................................................................ 30
6) Folding Line (distance) Adjustment ............................................................................ 30 9.
Standard Folding of No-Standard-Size Paper ....................................................................... 31
1) Measure paper length .................................................................................................. 31 2)-4) Input paper length ................................................................................................... 31
5) Paper Setting, Speed Selection, Air Control and Feed Table Skew Control ............... 32
6) Set number of sheets to fold ........................................................................................ 32
7) Start Folding ................................................................................................................ 32
8) Folding Line (distance) Adjustment ............................................................................ 32
10. Control (Adjustments) .......................................................................................................... 33
1) Fine Adjustment for folding line distance by Table 1 or 2 .......................................... 33
2) Stopper position Guide of Table 1 or Table 2 for each fold pattern ............................ 34
3) Skew Control Guidance Chart for 6 folding patterns by Feed Angle Adjustment Dial and Feed Table Angle ..................................................................................... 35-40
4) Separator Rubber Height ............................................................................................. 41
11. Memory ................................................................................................................................. 41
1) Fold Position Memory of No-Standard Sized Papers ................................................. 41
2) Fold Position Memory of Standard Sized Papers ....................................................... 42
3) Clearing Memory ........................................................................................................ 43
4) Clearing all the memorized patterns ........................................................................... 43
12. Check Lamps, Error Codes and Troubles ............................................................................. 44
1) - 7) Location Finder, Error Codes and Symptom .................................................. 44-46
13. Troubleshooting and Cleaning .............................................................................................. 47
1) Troubleshooting of Paper jam ..................................................................................... 47
2) Cleaning of Sensors ..................................................................................................... 48
3) Cleaning of Fold Roller and Paper Feed Belt ....................................................... 49-50
14. Other Adjustable Functions .................................................................................................. 51
1) Weight Arm .................................................................................................................. 51
2) Adjustment of Base Plate of Table 2 ............................................................................ 51
3) Folding Roller Pressure (Press Power) Adjustment .................................................... 52
Page 4 of 57

Text on page 5
Safety Instructions
Definition of Symbols and Notes The following names and signs stand for possible dangers.
This symbol stands for immediate danger. Disregarding these instructions may cause severe injury.
This symbol stands for a potentially dangerous situation. Disregarding these instructions may lead to injuries or damage to property.
Danger
Make sure that the machine is electrically grounded to prevent electrical shock. Operate the machinery within reasonable voltage range. There is a risk of electrical shock or fire if a higher or lower voltage is used, or if an electric current is utilized with a frequency not within the range stated above. Do not place any object on top of this machine. There is a risk of electrical shock or fire if water or any foreign object enters the machine. Handle the power cord with care. There is a risk of electrical shock or fire if the cord is damaged, broken, or placed under a heavy object. Do not insert or remove the power plug when water is present. Do not remove the cover of this machine. There is a risk of an electrical shock. Do not reconfigure the electronics of this machine. There is a risk of an electrical shock or fire. Do not operate the machine if it is emitting smoke or a strange odor. Turn off the machine, unplug it from the outlet and contact your dealer. Do not operate the machine if the power cord is generating heat or emits a strange smell. Turn off the machine, unplug it from the outlet and contact your dealer. If a foreign object enters into the machine, turn off the power switch and unplug the power plug, then consult your dealer. In the event of a thunderstorm, unplug the machine.
Caution
Keep hair, clothing, and jewelry away from the machine while operating. Serious injury may result. Do not put the machine on an unstable or slanted surface. Doing so may cause the machine to drop or fall over, causing damage and possible injury. Store and operate the machine in a clean, dust-free environment with low humidity. Avoid areas with high moisture, extreme temperatures and excessive dust, as these conditions may cause machine failure or electrical shock. Operate the machine at the temperature of 5 degrees to 35 degrees C. Be sure to grasp the power cord by the plug when unplugging it from the electrical outlet. Not doing so may cause damage to the cord and possible electrical shock or fire. Be sure to pull the power plug out of the electric outlet before moving the machine. Not doing so may cause damage to the cord and possible electrical shock or fire. Unplug the power plug from the electrical outlet when this machine is not in use. The socket-outlet shall be installed near the equipment and shall be easily accessible.
Page 5 of 57

Text on page 6
WARNIN
NG 1
①: Moving Pa arts
②: Warning Label L
WARNIN
NG
HAZARD
DOUS MOVI ING PARTS S
KEEP FI INGERS AN
ND OTHER R BODY PA RTS AWAY.
Page 6 of 57

Text on page 7
WARNIN
NG
①: Moving Pa arts
②: Warning Label L
WARNIN
NG
HAZARD
DOUS MOVI ING PARTS S
KEEP FI INGERS AN
ND OTHER R BODY PA RTS AWAY.
Page 7 of 57

Text on page 8
Model:
MBM 1800S Air Suction Paper Folder
Paper sizes:
Paper weight:
Bond 13.9 to 42.5 lbs (Bond 42.5 – 61.1 lbs for single fold with limited paper)
Paper quality:
Offset paper, Coated Paper
Folding patterns:
Single, Letter, Zigzag, Double Parallel, Fold-out and Gate* (*21.6-42.5 lbs Bond and Gate is limited to certain papers/prints)
Folding dimensions:
Maximum folding dimensions Table 1: 14.4” Table 2: 9.6”
Minimum folding dimensions Table 1: 2.0” Table 2: 2.0” Smallest adjustment increment: 0.003”
Paper feed system:
Belt Suction Feed system
Maximum capacity:
2.9”, or 800 sheets, Bond 20 lbs
Folding speed:
Max 18,000 sheets per hour (single fold, Letter) Speed adjustable in 5 steps.
Control system:
Automatic setting by built-in microcomputer
Other functions:
Automatic paper size detector (Letter, Legal and Ledger) Four-digit counter with addition/subtraction modes 18 memories for standard fold patterns (fine adjustment) 3 special memories for out of standard paper sizes Skew correction Double Feed Sheet Detection by Ultra-Sonic Sensor: Detects any double fed sheets such as White, Printed, Black and Transparent. Error Detection: Empty Feed, Empty Paper, Stacker full, Paper Jam and others. Interval Function Folding Roller manually removable without tool for cleaning Folding Pressure Adjustment (Thicker to Thinner Paper) Table #2, Base Plate Adjustable (Thicker to Thinner Paper)
88dB, 20 lbs Bond , double parallel at the highest speed level 5
Power source:
100 thru 240 VAC,
Dimensions:
Weight:
Net:
Options:
Perforation/Scoring Unit (12.5” ×17.7”) Large Capacity Stacker (Long Delivery) Interceptor for Table #2 (Used to fold double size Letter)
Shipping (Approx.):
Page 8 of 57

Text on page 9
After un-bo oxing, make sure that the following ac ccessories arre present. Pl lease contact t your local dealer immediately y if anything g is missing.
A Accessories
Quantity Q
Auxiliary y Paper Feed Table
Paper Ej jection Table e and Eje ection Roller
Page 9 of 57

Text on page 10
Auxiliar ry Paper Ejec ction Table
L St topper Guide
Paper Eje ection Contro ol Plate
W Weight Arm
Oper ration Manua al
Basic O Operation Ma anual
Page 10 of 57

Text on page 11
Top cover Left side cover Paper Guide(Left & Right ) Paper Height Detection Sensor Auxiliary Feed Table Table 1 Operation Panel Paper Feed Table Door for Table 2 Right side cover L Stopper guide
Number ⑫ ⑬ ⑭ ⑮ ⑯ ⑰ ⑱ ⑲ ⑳
Name Skew Adjustment Knob Paper Ejection Table Paper Ejection Roller Auxiliary Paper Ejection Table Power Switch Paper Ejection Table Socket Air Adjustment Knob Weight Arm Top cover Knob Table 2
Table 2 is set under the Paper Feed Table in the machine, which you find when opening the door ⑨ for the table 2.
Page 11 of 57

Text on page 12
Upper Cover is open o to adj just
belt fee eder assemb bly.
Erro or Code Cha art
Paper Floa ating Heigh ht Adjuster
Belt B Feeder Assy A
Suction Air A djuster
Feed An ngle Adjustm ment Dial
Page 12 of 57

Text on page 13
Des signation
n and Fu unctions of Oper rations Panel P
No. ①
D Designation n/Indication STAR RT/STOP key y
T key TEST
Spee ed adjustment key Pape er feed table up p/down key Store e key mory 1/2/3 key y Mem Fold type key
Num merical key
y Table e 2 stopper mo ove mode key y Table e 1 stopper mo ove mode key Pape er length input t mode key Pape er ejection roll ler move key Inter rval key Doub ble Feed Error r Detection ke ey M Trou uble Locating Map ①② ②③④⑤ In ca ase of Double Feed
Perfo oration mode lamp
Fu unction
Start ts and stops ma achine.
- Te est folds two sheets s withou t counting.
- A Also used fo or test blow without fold ding (pressed d more than 2 seconds unti il buzzer soun nds.) Sele ect 5 speed.
Mov ves up and dow wn the Paper Feed F Table Mem morize fold po osition after ad djustment is do done.
Mem morize three sp pecial fold type es.
Sele ect 6 fold type s and store job b routine. Show ws the numbe er of sheets, p osition of the e stopper of Ta able 1 and 2, and p paper size.
Clea ars the counter / resets after a n error.
Use for adjusting position of th he stopper of T Table 1 and 2 , the position of pa aper ejection roller, r and inp putting paper l length Use for inputtin g the numbe er of sheets to be folded d, length of non- -standard size paper, factors s of interval fu unction and ot thers. Use to adjust Tabl le 2 Stopper p osition. Use to adjust Tabl le 1 Stopper p osition. Use to input paper r length for no on standard no orm paper. Use to adjust posi ition of Paper Ejection Rolle er. Sets time and num mber of interva al function du uring folding work. w Sets double feed error e detection n ON/OFF.
Indic cates location of trouble. ①④ ④⑤ lamps fla ash at the same e time. Disp play indicates E-13. Indic cates when cle eaning of the FEED section n (belt, roller) is necessary. It lig ghts every 10, 000 sheets of folding. Can disable this function. fu Ref fer detailed se ection. Indic cates when th e optional per rforating unit i is installed.
Page 13 of 57

Text on page 14
Setu up after r opening g transpo ort pack king
- Setting of Paper Ejection E Tab ble
Install Pap per Ejection Table T to the main m machin ne body.
Install the Table by put tting its hook k on the guid de pins at two o
ns. Make sure that the hoo oks are secure ely hung on the guide pin
Place Pap per Ejection n Control Plate P undern neath Ejecti on
Roller Sha aft and fix by y Thumb Scre ew.
Paper Ejection Co ontrol Plate e
A Auxiliary Pa aper Ejectio n Table
Install Aux xiliary Pape er Ejection ta able to the P Paper Ejecti on
Page 14 of 57

Text on page 15
Plug in E lectric Conn nector of Pa aper Ejection n Table to the t
B Bracket
Settin ng of Table 1
Check th hat Set Le ever on bot th sides ar re positione ed in
UNLOCK
K.
Slide in n Bracket (R RH & LH) o of Table 1 sl lowly
into diago onal directio on along the guides of th he main mac chine
Tabl le 1 Bracket t Guide
n Operation P Panel side. The Table 1 connector is located on
Connector when w Give utmo ost care not to damage t he Electric C
installing t the Table 1.
E Electric Con nnector for T Table 1
Page 15 of 57

Text on page 16
Table e 1 Guide
Table 1 Br racket Guide e on the opp posite side w wall of Opera ation
Lock Le ever
f it Install Tab ble 1 to the main machi ine body sec curely and fix
using Lock k Levers loca ated on both sides. (Mov ve top of the lock
lever to the e direction o f arrow as sh hown in the r right figure.) )
Settin ng of Table 2
Make sure e that no pap per is loaded d on Paper F Feed Table, and a press the P Paper Feed Table T Up an nd Down Key y so as to ra aise the table u until it stops at a the upperm most point. For install ing or remov ving table 2, do it after ra aising the pap per feed table up to the highest h point using the p paper feed ta able Up and Do own Key. In case the e paper feed table is loca ated at any p place other th han the lowerm most point, if the paper r feed table Up and Do own Key is pr ressed, it moves m down n to the low wermost po int. Therefore, , press the pa aper feed tab ble Up and D Down Key ag gain to raise it t to the upperm most point. In case the e paper feed d table is loc cated at the l lowest point t, if the paper feed table Up U and Dow n Key is pre essed, the ta able moves up. wn Key is pr ressed while the If the pape er feed table Up and Dow paper feed d table is in n operation, the paper fe eed table sto ops motion.
Feed Table T
and Dow wn Key
Page 16 of 57

Text on page 17
Open the door for the Table 2.
There you u see the Flat t Set-Up Bas se for Table 2 2.
Table T 2 flat se et up base
Place Tab ble 2 just flat on the Set-U Up Base.
Page 17 of 57

Text on page 18
Push in th he rear side of Table 2 until u it is cau ught by rece ess of
You fe eel click here .
Plug in th he electric co onnector for Table T 2.
Close the e Door for the e Table 2.
Settin ng of the Au uxiliary Pa per Feed T Table
Push in G Guide Slots of Auxilia ary Paper F Feed Table into
2 Flange P Pins of Paper Feed Table.
Page 18 of 57

Text on page 19
After Aux xiliary Paper Feed Table is set, make e sure the P aper
Feed Table e and Auxilia ary Paper Fee ed Table Sur rface is flat.
Conn necting Pow wer Cable
Insert the power cable e into electr ric inlet of m machine and d the
other end t to electric po ower outlet.
Caution:
Make sure e to connect t to the elec ctric power outlet equip pped
with groun nd terminal.
Do not use e a power cab ble other than n the one pro ovided.
Page 19 of 57

Text on page 20
Turn on the Pow wer Switch..
Page 20 of 57

Text on page 21
Fan out the paper sufficiently.
If paper edges are bent or warped,
Keep the stacking capacity.
Max. 800 sheets (20 lbs)
Max. (80g/m2 2.9” weight) height
It should be noted that when paper stack as thick as 2.9” or more is placed on the Paper Feed Table, smooth feed may not be available. Also it may cause damages to the machine.
Page 21 of 57

Text on page 22
Init tial Setti ing
To s start using g this mac hine, for e ease of pr actice, exp planation i is describe d, whereve er
applicable e, for Ledge er paper si ize and 24 lbs Bond paper p with h Single Fo old at medi ium speed 3.
This intro oductory op peration in ntends to m make the user u becom me familiar r with oper ration of th he
machine s so that it w ill be easie r for applie ed applicati ions.
After r abovemen ntioned pra actice, it is recommen nded to use other pape er sizes, pa aper weight ts,
folding pa atterns and different speeds. s
Prepa are approxi imately 200 0 sheets of L Ledger(11” ” × 17”),
24 lbs s,Bond Pap per. Pape r corners m must be cut t exactly 90 de egree angle s.
Turn Power Swi itch on.
To set t the paper, r, press Feed d Table up/ /down Key y and place the Feed Table at lo owest positi ion.
Note e: When se etting sheets of paper on n the Paper Feed Table, press the P Paper Feed Table T Up/Do own Key. In case the Pa aper Feed Ta able is locat ted at any pl lace other tha an the lowes st point, it moves m down to the lowe est point once e. In ca ase the paper r feed table is i located at the lowest point, p if the Paper Feed d Table Up/D Down Key is pressed, p the table moves up. If the e Paper Feed d Table Up/D Down Key is pressed whi ile the paper feed table is s in motion, the table stop ps at the e position.
Note e: In case of o installing or removing g Table 2, do d it after ra aising the Pa aper Feed Ta able up to th he highe est point usin ng the Paper Feed Table U Up/Down K ey.
Open Top Cover r.
Widen n Paper Guides, G and d load the 200 sheet ts of Ledg ger Paper in portra it on Pape er Feed Table T whic ch is alrea dy connec ted with A Auxiliary Feed F Tabl le. Paper should s be fanned f out a and jogged well
prior to loading. Standard norm paper sizes within n this mach hine speci ifications are e automatica ally recogniz zed by the Fo older, i.e., i in this case as a Ledger.
Note e: Set up Pape er while lifti ng Weight A Arm slightly.
Page 22 of 57

Text on page 23
Fit Paper Side Guides along the paper edges and tighten Two Thumb Screws.
IMPORTANT:
Leave no gap between Leading Edge of the Paper and Machine Front Stopper Wall. Such gap may cause paper skew. Use Feed Table Skew Adjustment knob at Feed Table to Remove unnecessary gap between Paper Leading Edge and Machine Front Paper Stopper Wall.
Machine Front Stopper Wall
Paper & Feed Table
Paper & Feed Table
Skew Adjustment Knob at Feed Table
Page 23 of 57

Text on page 24
Skew Correction n is done by y two meth hods.
- By Fe eed Angle Ad djustment Di ial (by Drum m-Feed-Rolle er) For les ss than 34.3 lbs l Bond pap per, Feed An ngle Adjustm ment Dial is u sed. This m method is use ed relatively lighter paper r and fine adj justment. Refer p page 35 - 40 for each fol ding pattern. .
Fee ed Angle Ad djustment Dial D
P aper Feed D Direction
Refer Pin W Window as gu uidance for original o angle e and adjuste ed angle.
- For ov ver 34.3 lbs Bond B paper, Skew S Adjustm tment Knob at a Feed Table e This m method is use ed relatively heavier pape er which cann not be contro olled by Feed d Angle Adju ustment Dial l. Also it t is used for eliminating e gap g between paper and Machine M Fron nt Stopper W Wall at first pa aper loading g. Refer P Pin Window as guidance for original angle and ad djusted angle e. S Skew Adjus tment Knob b Refer p page 35 – 40 0 for each fol lding pattern n.
P Pin
Set L Stopper at t the rear en nd of the P Paper.
Clo ose the Top Cover.
CAU UTION: Fo or security, Top Cover shou uld be closed d holding by y two hands.
Page 24 of 57

Text on page 25
Trial l Air Blow, Trial Pape er Floating and Trial Suction S (Ai ir Control) )
- Air r Blow Stre ngth Adjus stment for sheet separ ration
(i)The air blow stre ength can be adjusted
by tu urning the ai ir adjustment t knob from thin to high, i.e.,
wea aker to strong ger.
Gen neral Guidanc ce:
Whe en double fe ed occurs, tu urn the air adj djustment kno ob
towa ard weaker position p sligh htly.
Whe en paper is not n fed, turn the t air adjust tment knob
towa ard stronger position slig ghtly.
Note e:
n encourage e that you ch hange positio on of We do not
Air A Adjustment Knob extrem mely from the e original po osition.
(ii) Tri ial Air Blow without feed ding paper
To f find if paper is separated properly for r feeding, tria al air blow ca an be done.
Pres ss Test Mode e Key for mo ore than 2 sec conds until buzzer b sound s.
The en air starts to o blow and Paper P Feed T Table rises wi ithout feedin g paper.
ment Knob so o that the lea ading edge of f top (iii) Ad djust Air (Bl ow) Adjustm
5 to 7 sheets flie es in the air with w stability y/steadily and d without stic cking two
Dial is set more or less s at thin posit tion (weaker r blow)
as p picture right hand h for Led dger(11” × 1 17”), 24lbs, Bond B paper for f practice.
Obse rve Top Lead ding Edge of f Paper from m both sides of o paper stack k.
sepa arated.
Page 25 of 57

Text on page 26
(iv) W Weight Arm for f charging air between sheets
In case upper 5 – 7 sheets chatter, c use o of Weight Arm m is effectiv e.
Refer pa aragraph 14- 1,
We eight Arm, p age 51.
- Pape er Floating Height H Adju stment relat tive to Sucti ion Belt.
Pap er Floating Height H and Strength S of A Air Blow are adjusted a so t hat paper is f fed consisten ntly.
For this practice e of Ledger(1 11” × 17”), 2 24lbs, Bond paper, use p osition 2nd f from THIN.
Gen neral Guidan ce:
Thic cker paper or r paper not easy e to suck u up, set for th hicker positio on.
Thin nner paper o r paper tends s to make do ouble feed, se et for thinner r position.
- Adjus stment of Su uction Air S trength
When n folding thin nner papers which w tends to make dou uble feed, adj just suction p power lower .
At th inner positio on, suction po ower is lesse er.
At thick ker position s uction power er is stronger. .
In cas se frequent double d feed is i observed, s slide, adjust and tighten the t Dial at th hinner positio on.
For L Ledger(11” × 17”), 24lbs s, Bond pape er, position dial d between thin and mid d.
Page 26 of 57

Text on page 27
- Appr roximate Gu uidance of Suction S Air a and Paper Feed F Table Height H
Adjust tment of Suc ction Air and d Paper Feed d Table Heigh ht depend on n paper quali ity, print con ndition or oth her
enviro onment. So ad djust them by y referring to o the followi ing table as approximate a guidance.
Paper P Floating g Height
6 Graduati ions (Linear)
5 Graduations s (Linear)
5 Graduation ns (Linear)
5 Graduation ns (Linear)
17 lb bs
Bond B Paper
Graduation n
Graduation G
Blow A Air Control
Paper Flo oating Height
General G Guidance:
- In case D Double Feed is s frequently o bserved, set th hinner side fo or appropriate control dial.
- In case E Empty Feed is s frequently ob bserved, set th hicker side for r appropriate control c dial.
- In case u upper 5 – 7 she eets are chatte ering, use of W Weight Arm is s effective. Refer R
paragraph h 14-1, Weigh ht Arm, page 51.
Page 27 of 57

Text on page 28
Selec ction of Fo lding Patte ern.
6 pre eset folding patterns, p Sing gle, Letter, Z Zigzag, Doub ble Paral llel, Fold-out t and Gate, are a available. .
Key lights. For t this practice, select Singl e Fold and K
Selec cting Foldi ng Speed
S peed is adjus stable in 5 st teps by L Key y and H Key y. Speed is L lamps, slowest s in th he extreme le eft and in ndicated by LED fa astest in the extreme e righ ht. Medium m speed is 3 rd light from th he left. D Depending on n paper quali ty, paper thic ckness and paper p folding g pattern, se elect adequat te folding sp eed.
N Note: In cas se folding thi ick paper, it m may recomm mend to use faster f speed. In n case paper gets wrinkle e, use slower speed.
In n this practic ce, select Me edium Speed d by using L or o H Key.
- Test F olding
Pr ress TEST Ke ey and 2 she ets are folded d in sequenc ce without co ounting Coun nter. nd Ex xamine 2 fo olded sheet whether w folde ed as desired d.
N Notes:
- ) In case fol ding position n is not as de esired, adjust t Position of Stoppers at Table 1 or Table 2 or b oth. ment in page e 34. Refer Sto pper Adjustm
- ) In case ske ew is found, adjustment i is necessary. Refer Skew w Adjustmen nt in page 35 through 40.
- ) In case Do ouble Feeding g or Empty F Feeding occu ur, adjustmen nt of Separation n Air Blow, Paper P Floatin ng Height or Suction Air Strength is n necessary. Refer Air Adjustments A in page 25 th hrough 27.
Page 28 of 57

Text on page 29
16) Other Controls and a Functio ons
(a) Adju stment of Pa aper Ejectio on Roller Lo ocation
a paper size is standard Roller automaticall ly sets at the preset positi ion as long as
In case of Out of Stand dard Norm P Paper, press Paper P Ejectio on Roller
Move Key. By pr ressing + or - Key, move e the Roller and a position where w roller
Effecti ively works for f specific folds f the pap per size.
After p position is se elected, press s Paper Eject tion Roller Move M Key ag gain.
Depen nding folding g speed and pattern, p the R Roller need to o be relocate d.
Smalle er numeral sh hows locatio n of Roller c closer to mac chine body.
(b) How to Use Inter rval Functio on
(1) After s selecting a fo old type,
Press the Interval key.
The lam mp on the In nterval Key i lluminates.
- The ba ar on the disp play right be side “SEC” f flashes.
Using g the numeric cal keys “1” or “10”, inpu ut a desired
interv val time for in ntermittent operation. o
1 to o 99 seconds can be set as s the interval l time.
- Press t the Interval key k again.
The ba ar on the disp play right bes side “SET” f flashes.
Using the numeric cal keys “1 ”, “10” or “100”, inpu ut a
desired d number of f sheets of paper p to be folded for each e
1 to 9 999 sheets ca an be set for interval oper ration.
Paper Ejec ction Roller Key
Page 29 of 57

Text on page 30
- Press t the Interval key k again.
Then, t the lamp on n the Interva al key flashe es indicating g the
workin ng procedure is set.
- Press t the TEST key y or START key to start p paper folding g.
(When n pressing the t TEST key k first, th hen the cou unter
functio on is not effe ective, i.e, tes st sheets are not counted. .)
- How to o clear Interv val Mode
Press t the Interval Key K and pres ss the Clear K Key or input “0”. Then, t he interval fu function is cl eared.
Example:
a interval tim me and 50 sh heets fold as number of s heets for inte erval operati ion. How to se t 8 seconds as
By this s etting, the machine m wi ll stop for 8 seconds after folding g 50 sheets , and start folding agaain
How to set :
① Press t the Interval key. k
② The ba ar beside “SE EC” flashes. Using the nu umerical key y, input “8”.
③ Press t the Interval key. k
④ The ba ar right besid de “SET” flas shes. Using t the numeral key, input “5 50”.
⑤ Press t the Interval key. k The lam mp on the Inte erval key flas shes.
⑥ Set the e speed accor rding to the paper p quality y and fold typ pe.
⑦ After s setting, press s the TEST key k or START T key to star rt folding.
⑧ In case e of making preset p numb er of folds w with the Interv val function is set,
input t the desired p reset number r while the la amp on the Interval key is i flashing.
Then, t the machine stops after th he preset num mber of shee ets of paper are a processed d.
Note:
he units digit t is lit, it show ws when the dot below th
that th e preset valu ue is input an nd valid.
When it is not lit, i t is not valid d and the mac chine continu ues to proces ss
until th here is no pap per loaded o n the paper f feed shelf.
- Doub ble Feed Det tection or No o-Detection
De etection Acti vated: Light is ON . De etection De-A Activated: Light is OFF F.
In case double feed is detec cted, machin ne stops. Th he double fed d sheets are folded f and ex xhausted but t stays on the e Output Pap per Ej ection Table . Counter un-counts u the e double fed sheets. Re emove doubl le fed sheets and clear Er rror Indicatio on by Cl lear/Reset Ke ey.
Page 30 of 57

Text on page 31
Sta andard fo olding of f Standa ard-Size Paper
Follow w instructions s for machine e and paper s setting in
Section 7-1)-(0) thro ough 7-1)-(1 4)
- Selectio on of Foldin ng Pattern
6 prese et folding pa atterns, Singl e, Letter, Zig gzag, Double e Parallel, Fo old-out and Gate, G are ava ailable.
- Selectin ng Folding Speed
Speed is adjustable e in 5 steps by b L Key and d H Key. Speed is indicated by LED lam mps, slowest i in the extrem me left and fas stest in the e xtreme right t. Medium speed is 3 rd light l from th he left. Dep pending on paper p quality y, paper thick kness and pap per folding pattern n, select adeq quate folding g speed.
Note: In case fol ding thick pa aper, it may r recommend to use faster speed. In case e paper gets wrinkle, w use slower spee d.
In this practice, sel lect Medium m Speed by us sing L or H Key. K
4) Set num mber of she eets to fold. .
(a) Sub btraction Co ounter Mod de Fo or practice, here h 100 shee ets is to be fo old. Pre ess C Key to o reset counte er to 0 (zero) ). By y number Key y set 100. By B one time press of 100 Nu umber Key, it ts sets 100. By pressing g twice, it s sets 200. In this subtract tion counter mode, m machi ine folds unt til counter be ecome 0 (zer ro)
(b) Ad dding Up Co ounter Mode e If c counter is se t zero, mach ine folds unt til sheet is em mpty on Pape r Feed Table e.
No ote:
when the dot belo ow the units d digit is lit, it shows that th he preset val lue
is input and va alid. (Subtrac ction Counte er Mode)
W When it is not t lit, it is Add ding Up Cou unter Mode.
- Start Fo olding
By pre essing STAR RT/STOP Key y, machine co ontinues to fold pa aper. Durin ng folding op peration, whe en START T/STOP Key y is pressed, machine m stop ps folding. In case e when STAR RT/STOP Ke ey is pressed d and machin ne restart and counter r number is effectively e co ontinuous. ng mode dep pends on nee ed. Use Ad dding Mode or Subtractin
- Folding g Line (dist tance) Adju ustment
Re efer Section 8 (Control)-1
- Fine Adjus stment for fo olding distan ces by Tab ble 1 or Tabl le 2. Page 33 3 – 34.
Page 31 of 57

Text on page 32
Sta andard Folding F of o No-Sta andard- Size Pap per
Selecting a fold type first fi and then input total pa aper length
- Measu ure the pape er length.
The arro ow indicates the direction n of paper fee ed.
- Press P Paper Leng gth Input Mode M Key.
- Input t the paper l ength using g the nume erical keys. .
Th he unit for in nput is inch. Fo or example: Input paper length l of 11. .42 inch Pr ress [1000] key k 1 times. (Input ( unit o of 10 inch) Pr ress [100] ke ey 1 times. (I Input unit of 1 inch) Pr ress [10] key y 4 times. (In nput unit of 0 0.1 inch) Pr ress [1] key 2 times. (Inp put unit of 0.0 01 inch)
k are high her by 10 tim mes N ote: Units of f numerical keys than the e unit of leng gth
T The available input range is 13.0 to 19 9.25inch .
- After t the length is i set, pres ss the Pape er Length Input Mod de Key aga ain to fix it t. When an ny value ou ut of stan ndard lengt th from ma achine spec cifications i s input, the e lamp flas hes. To clea ar the inpu ut value, pr ress the Len ngth Input t Mode key and then press p the “C C” key.
Page 32 of 57

Text on page 33
- Paper P Preparation n, Paper Se etting, Spee ed Selection n, Air Cont trol and Fe eed Table Sk kew Controol are the s same proce edures as Standard S Fo olding of S tandard No orm Paper. r.
Refer pa ages 20 – 28 8 and 33-40.
6) Set num mber of she eets to fold. .
a) Subtraction Counter Mo ode F For practice, here 100 she eets is to be f fold. P ress C Key to t reset coun ter to 0 (zero o). B By number Key K set 100. By one time e press of 10 N Number Key, its sets 100. By pressin ng twice, it t sets 200. In n this subtrac ction counter r mode, mach hine folds un ntil counter become b 0 (ze ero)
b) ) Adding Up p Counter Mo ode If f counter is s et zero, mac hine folds un ntil sheet is em mpty on Pap per Feed Tabl le.
7) Start Fo olding
By y pressing ST TART/STOP Key, machin ne continues s to fol ld paper. During D foldin ng operation, when ST TART/STOP Key is press sed, machine e stops foldin ng. In case when START/STOP S P Key is pres ssed and ma chine res start and cou unter number r is effectivel ly continuou s. Us se Adding Mode M or Subtr racting mode e depends on n need.
- Folding g Line (dist tance) Adju ustment
Re efer Section 8- 8 1) Fine Ad djustment for r folding dist tances by Tab ble 1 or Tabl le 2. Page 33 3 – 34.
Page 33 of 57

Text on page 34
Co ontrol (A Adjustm ents)
Fine A Adjustmen t for foldin ng distances s by Table 1 or Table 2
Select the Stopper Mov ve Mode key y (Table 1or 2 2). The
Table 1 Stopper Mo ove Mode Key K
lamp of the e selected St topper Move Mode key il lluminates.
The curren nt stopper po sition is show wn on the [C Counter].
In case of s standard-size e paper, the stopper s move es
automatica ally to the su uitable positio on according g to the
paper size and fold typ pe.
Apply this adjustment when fine ad djustment is in need for
the folding g position.
Values inp ut manually return to sta ndard values s if any one
of other fo old type keys is pressed.
Table 2 Stopper M Move Mode Key K
Press the + +/- key and move m the stop pper to the de esired positio on.
The value displayed on n the [Count er] shows th he position of f the
stopper. (U Unit: mm)
Example: : When dis splay of the e [Counter] is 11.38”, the
position is 11.38 inch.
The positio on can be mo oved based on o a unit of 0 0.003 inch.
Press the S topper Move e Mode key (T Table 1 or 2) again.
The lamp o on the Stoppe er Move Mod e key flashes s.
Refer table e for adjustme ent at page 34 4.
Folding p ositions of sheet are determined d b by the Stop ppers
positions o of Table 1 an nd 2.
Double arr rowed line (
) shows the le ength the she eet is
folded by t the specific Table. T
Example, , In case of Double D Paral lel,
Table 1: F Fold a half o f the overall length
Table 2: F Fold one fou urth of the ov verall length
Note:
machine autom matically let Interceptor Pu Push Bar go down d and pu ush In c case of Single e Fold Key i s pressed, m
Inte erceptor, i.e., Table 1 is clo osed by Inter rceptor and it by-pass foldi ing sheet to T Table 2.
In t this case, eve en Table 1 St opper Move Mode Key is s pressed and d + or – Key is pressed, In nterceptor Pu ush
Bar r does not co ome down to contact with Interceptor. This avoids s accidental b bending of In nterceptor Pu ush
Not te:
Folding position may y change depe ending on hu umidity, temp erature, paper er stretches or r shrinking.
In t that case, do fine f adjustme ent for Table 1 or Table 2.
Page 34 of 57

Text on page 35
- Stopper position guide of Table 1 or Table 2 for each fold type
SINGLE
DOUBLE PARA LLEL
FOLD-OUT
LETTER
ZIGZAG
GATE
Feed Out Direction of
Page 35 of 57

Text on page 36
- Skew C Control Gui idance Cha art for 6 for rding patte erns by Fee ed Angle Ad djustment Dial D and by Feed Table e Angle.
Skew Adjus stment by fold ding pattern
Bold line ind dicates leadin ng edge when paper is plac e on feed try.
Shadow indi icates upper surface s when n paper is on feed f tray.
Feed d Roller Direction n Adj.
Turn Meta allic Thumb Screw S
Turn Me etallic Thumb b Screw
Dial ( (Less than 34.3 lbs l Bond)
Counter rclockwise ( - )
Cl lockwise ( + )
(Mo re than 34.3 lbs Bond or
Turn T Thumb Screw w
Turn n Thumb Scr rew
Feed R Roller Direct. Ad dj. Dial is
Skew Adj. Kno ob
N NOTE:
D o not use, , at the sa ame time, Feed Roll ler Directi ion Dial a nd Skew
A Adjustment t
How stacke ed and folded d
Bold lin ne indicates leading
feed edge e when paper r is place
P Paper Feed Dir rection
on feed tr ry.
Shadow in dicates upper r surface wh hen
paper is on n feed tray
Page 36 of 57

Text on page 37
Bold line ind dicates leadin g edge when paper is place e on feed try.
Skew Adjus stment by fold ding pattern
Shadow indi icates upper surface s when n paper is on feed f tray.
- ) Double Pa arallel
Tur rn Metallic Th humb Screw
Turn Meta allic Thumb Screw S
Clockwise e ( + )
Counte erclockwise ( - )
(More th han 34.3 lbs Bond d
Turn Thumb b Screw
Turn T Thumb Screw w
Clockw wise
Feed R Roller Direction
D Dial (Less than
- 3 lbs Bond)
Skew w Adj. Knob
Feed Ro oller Direct. Adj. .
Dial is s not effective)
NO TE:
Do no ot use, at th he same tim me, Feed Roller R Direc tion Dial an nd Skew A djustment
Kno ob unless re eally neede ed.
Page 37 of 57

Text on page 38
Skew Adjus stment by fold ding pattern
Bold line indicates lea ading edge wh hen paper is place p on feed
Shadow in ndicates uppe er surface wh hen paper is o n feed tray.
Fold d-out
Feed d Roller Direction n Adj.
Turn Metal llic Thumb Sc crew
Turn M Metallic Thum mb Screw
Di al (Less than 34. .3 lbs
Cloc ckwise ( + )
Coun nterclockwise e ( - )
(Mo ore than 34.3 lbs s Bond
Turn T Thumb Screw w
Tur rn Thumb Sc rew
Co ounterclockw wise
Skew Adj. Kno b
Fee ed Roller Direct . Adj.
D Dial is not effecti ive)
NOTE:
D not use Do e, at the same time e, Feed Ro oller Direct tion Dial and Skew
Adjustmen nt
How stacke ed and folded d
Page 38 of 57

Text on page 39
Bold line indicates lead ding edge wh hen paper is place p on feed
Skew Adjus stment by fold ding pattern
Shadow in ndicates uppe r surface whe en paper is on n feed tray.
Fee ed Roller Directio on Adj.
Turn Met tallic Thumb Screw
Turn M Metallic Thum mb Screw
Dial (Less than 34.3 lbs Bond)
Count terclockwise ( - )
Clockwise ( + )
(Mo ore than 34.3 lbs s Bond or
Turn n Thumb Scre ew
Tu urn Thumb S crew
Feed d Roller Direct. Adj. A Dial
T To the Left
To the Righ ht
Skew Adj. Kn nob
is not effectiv ve)
NOTE:
D not use Do e, at the s ame time, Feed Roll ler Directi ion Dial an nd Skew
Adjustmen nt
How stac cked and fold ded
Page 39 of 57

Text on page 40
Bold line ind dicates leadin ng edge when paper is plac e on feed try.
Skew Adjus stment by fold ding pattern
Shadow indi cates upper s urface when paper is on fe eed tray.
Zig gzag
Feed d Roller Directio n Adj.
Turn Metal llic Thumb S crew
Turn Me Metallic Thumb b Screw
D ial (Less than 34 4.3 lbs
Cloc ckwise ( + )
Coun nterclockwise e ( - )
(Mo ore than 34.3 lbs Bond or
Turn T Thumb Screw w
Tur rn Thumb Scr rew
Fe eed Roller Direct t. Adj.
Co ounterclockw wise
Skew Adj. Kno ob
Dial is not effect tive)
NOTE:
Do not us se, at the same time e, Feed Ro oller Direct tion Dial and Skew
How stac cked and fold ded
Page 40 of 57

Text on page 41
Skew Adjus stment by fold ding pattern
Bold line ind dicates leadin g edge when paper is plac e on feed try.
Shadow indi icates upper surface s when paper is on fe eed tray.
- Gate G
Fee d Roller Directio on Adj.
Turn Metall lic Thumb Sc crew
Turn Me etallic Thumb b Screw
D Dial (Less than 34 4.3 lbs
Counterc clockwise ( - )
Cl lockwise ( + )
(Mo ore than 34.3 lbs Bond or
Turn Th humb Screw
Turn n Thumb Scre ew
Fe eed Roller Direc ct. Adj.
T To the Right
Skew Adj. Kno ob
Dial is not effect tive)
NOTE:
D not us e, at the s same time Do e, Feed Ro ller Direct tion Dial and a Skew
How stacke ed and folded d
Page 41 of 57

Text on page 42
- Separat tor Rubber r Height Ad djustment
When adjus sting the sepa arator height, , turn the sep parator adjust tment knob using u a flathe ead screwdri ver. Adjust th he
height so tha at the tip of th he separator rubber r touche es the paper feed f belt sligh htly.
Paper Feed Belt B and Sepa rator narrowe er. If double fee ed frequently y occurs, gap between the P
If empty fee ed frequently occurs for th hick paper, op pen about a 0. .5mm gap bet tween the Pap per Feed Bel t and Separat tor
U Use several sh heets of paper r for filler gau uge.
Top of f Separator Rubber
Bottom m of Suction n Belt
Gap be etween Bot ttom of
Suctio on Belt and
Separa ator Rubber r is set
approx x.. 0.5mm.
Separ rator Heigh ht Adjustme nt Knob.
Right t Turn:
Sep parator high gher
Left Turn:
Se eparator low wer
ustment Knob b clockwise, the t separator raises to dire ection of pape er feed belt. By B By turning t the Separator r Height Adju
turning the Separator Ad djustment Kn ob counterclo ockwise, the separator com mes down to opposite dir ection of pap per
M Memory
- Fold Po osition Mem mory of No o-Standard Sized Pape ers
Non-stand ard folds se etting can be b stored by y the memor ry
M1/M2/M M3 keys.
The positio ons of the st toppers of th he Tables 1, 2, position of o
the ejection n roller, and d folding spee ed are, as a s set, saved in n a
Page 42 of 57

Text on page 43
Input desi ired length of folding position an nd select th he Memory K Key, M1, M2 2 or M3, in which w the fo old is intende ed to be store d. Press the Store Key and a release immediately y after a bee ep sound.
t fold patt tern has bee en The lamp of the key in which the
memorized d will flash.
Memory r remains stori ing specific setting even n main Pow er
Switch is turned off, i.e., when P ower Switch h is turned on o
again, mem morized patte ern can be us sed again.
- Fold Po osition Mem mory of Sta andard Size ed Papers
nt, In case desi ired to adjust t folding posi ition, after fin ne adjustmen
adjusted fo lding positio on can be memorized m a at the foldin ng
3 paper siz ze between Ledger L thru L Letter, 6 kind ds
of folding p pattern can be e allocated. That is 18 ( = 3x6 ) kind ds
of fine adjus sted value can n be memoriz zed.
The position ns of the stop ppers of the Tables T 1, 2, p position of th he
ejection rol ller, and fold ding speed are, a as a se et, saved in a
Store Key and d release imm mediately afterr a beep soun nd. After fine ad djustment of fold position s, press the S
(Regarding fine adjustme ent method, refer r to Adjus sting Table 1 or Table 2
The lamp o f the key in which the fo old pattern ha as been mem morized will
Note:
By this setti ing method, out o of standa ard folding pa attern for stan ndard sized
paper can be e memorized .
Page 43 of 57

Text on page 44
- Clearin ng Memory y
How to clea ar the memor ry storage in n M1/M2/M3 3 keys and th he fold type keys k
Press first a desired Memory M M1/M M2/M3 Key y or Fold Typ pe T keep pressing p the e C Key an nd Key being g stored. Then release imm mediately aft fter a beep so ound. The lamp o of the key in n which the storage s has b been cancelle ed will light.
Note:
The lamp o of the key in n which the fo old pattern is s currently
- Cleari ng all the memorized m d patterns, i.e., reset to t factory d default.
Turn o off the pow wer first and d then while e pressing th he Clear/R Rest Key, tur rn on the pow wer again.
Note:
All the stor red pattern in ncluding custo om fold you m memorized are a
G Give utmost attention bec cause there is s no chance to
recall curre ent memories after clearan nce.
Page 44 of 57

Text on page 45
Ch heck Lam mps, Err ror Code es and Troubles T
1) If Chec ck lamp (1) is i flashing it t may indica ate:
(2) Paper F Feed Table is s stack.
(3) Failure e of the Paper r Height Sen nsor
(5) Excess ive loading of o paper
2) If Chec ck lamp (2) is i flashing it t may indica ate:
(1) Improp per setting of f Table 1
(2) Stoppe r lock at Tab ble 1
i flashing it t may indica ate:
3) If Chec ck lamp (3) is
(1) Electric c plug of Tab ble 2 is not in nserted
(2) Stoppe r lock of Tab ble 2
4) If Chec ck lamp (4) is i flashing it t may indica ate:
(1) Paper J Jam
Page 45 of 57

Text on page 46
5) If Chec ck lamp (5) is i flashing it t may indica ate:
(1) Electric c plug of the e Paper Eject ion Unit is n not inserted
(2) Ejected d paper is ful ll
(3) Ejected d paper jamm ming.
(4) Paper e ejection sens or is dirty by y dust or ink
6) If Che eck lamp (6) ) is lit, it may y indicate:
Perforator Unit (Option nal) is install led
- If Che eck lamp (7) ) is lit, it may y indicate:
It lights af fter every 10, ,000 sheets o f paper folded d. ・For rese t, turn on the machine wh ile pressing – Key. ・You can n disable this function whe en you turn o on the machin ne while kee ep pushing [S Single (Fold type)] t key. ・You can n activate thi is function ag gain when yo ou turn on th he
machin e with[Gate(F Fold type)] k ey pushed.
Clean the Paper Tran nsport Belt as frequent tly as neede ed n and paper quality eve en depend on n the printin ng condition before the cleaning lam mp is lit. Regarding the cleaning g method, ref fer to Cleani ing of Senso rs oller/Paper F Feed Belt of of page 38 and Cleanin ng of Fold Ro Page 39.
Note: : I If paper is lo oaded immed diately after p printing, prob blems such as a jamming, double feed, , slipping, an nd w wrinkling may m occur. Ma ake sure that t the printing g ink is comp pletely dry, st tatics are gon ne and paper r i is well fanne ed out before e loading. If the mach hine is placed d in the vicin nity of a flu uorescent lam mp and the p paper size de etection sens sor m may not alw ways function n properly. I In such a cas se, place the machine aw way from the fluorescent lamp l influen nce.
Page 46 of 57

Text on page 47
For each error symptom, the following error code will be displayed.
Neither Table 1 nor Perforating/Scoring unit is installed to the position of Table 1 unit.
Paper left in Paper Ejection Sensor area, or Paper Ejection Sensor is dirty.
Excessive loading of paper
Sensors need cleaning or Rollers need cleaning.
Paper Ejection Table Pluf is not connected.
Table 2 is not installed
Remove the Paper Ejection Table to use Perforator Unit.
Out of standard paper size, use Paper Length Manual Input Mode.
The door of the Table 2 is open, or Top Cover is open
Paper left in Paper Feed Sensor area, or Paper Feed Sensor is dirty.
Failure of Paper Height Sensor.
Failure of Feed Table Up and Down Motor
Failure of Main Motor, or the Encoder is dirty
Paper Ejection Roller is locked, or Motor Wire is disconnected, or Home Position Micro
Remove Double Fed Paper from Ejection Table.
Switch for Ejection Roller is disconnected or dislocated.
At Table 1:
Stopper is locked, or Stopper Motor is disconnected, or Sensor is
At Table 2:
Stopper is locked, or Stopper Motor is disconnected, or Sensor is
Note:
To clear Error Code from display, press CLEAR/RESET Key after cause of trouble is eliminated.
Page 47 of 57

Text on page 48
Tr roublesh
hooting and a Clea aning
CA AUTION:
Make sur re to discon nnect power r cable befo ore starting g the troubleshooting..
1) Troubl leshooting of Paper ja am
(1) Rem ove Table-1 and remove the paper or r pieces of pa aper.
(2) Open n Table-2 doo or, remove Table-2 T and re emove paper r or torn piec ces of paper.
Page 48 of 57

Text on page 49
- Cleanin ng of Senso ors
Clean e ach location of Sensor pe eriodically.
- Open T Top Cover an nd remove pa aper powder or dust by co otton swab, etc. e from the window
Circled d position as shown in the e following f figure.
- Clean P Paper Eject Sensor S (circle ed position a as shown in th he following g figure) by c cotton swab, etc.
(The pa aper eject se nsor is trans smission typ pe. Bottom Sensor S as se en in the Ci ircle and Up pper Sensor in
metal casin ng above.)
C Clean both Lower L and U Upper Sensor rs.
Especial lly note that Lower Sens or tends to get g
- Clean P Paper Detecti ion Sensor b y cotton swa ab. Locations s of Sensor on o the Paper Feed Table are a circled.
This s additiona al sensor is for Inch (I Imperial) ty ype machin ne only.
Met tric type 1 Sensor. S
Inch h type 2 Sen nsors.
Page 49 of 57

Text on page 50
- Clean ning of Fold d Roller an nd Paper Fe eed Belt.
When paper feed slips, s folding line does n not match as desired, wri nkled paper or inner pap per jam occu urs
frequen ntly, it may be e caused from m paper dust o or ink accum mulation on th e rollers.
- Clean ning Folding Rollers
By re emoving one Folding Roll ler, other thre ee Roller are accessible fo or cleaning w without remov ving them fro om
the m machine.
T 1 and Paper P Ejection n Table. Remo ove Folding Table
o both sides of Machine Frame. F Lift Rolle er Fix Lever on
Remove Press P Roller As A indicated b below.
Pre ess to left an nd then pul ll out.
Lever s lifted positi on
Clear r paper dust and dirt on each Roller r.
Re-install l the Rollers in reverse p procedures. For installin ng
Foldi ing Roller, tur rn the Roller for 2 to 3 tim mes so that the e Roller Gear rs positively e engage each other.
Page 50 of 57

Text on page 51
After r roller is rein nstalled, push down Roller r Fix Lever on n both sides of o Machine F Frame.
- Clean ning Suction Belt
a loosen 4 screw s of Suct tion Belt Cov ver. Open n Top Cover and
CAU UTION:
PAY Y UTMOST CARE C SO TH HAT SCREW WS DON’T D ROP IN THE E MACHINE E.
B Cover and d clean the B Belt by rotatin ng it. After cleaning, c fix Suction Belt Cover. Remo ove Suction Belt
Page 51 of 57

Text on page 52
Ot ther Adj justable Functio ns
CAUTION:
Turn off th he machine an nd remove Po ower Supply Cable from th he electric ou utlet.
- Weight t Arm, Purpo ose of using Weight W Arm
Weight Arm m is used as su upplemental tool t for contro rolling air flow w of sheet sep paration air.
air is charge ed within shee et pile so that t good consist tent sheet sep paration is av ailable.
By placing it, separation n
It is s especially effective e
for thinner p papers.
A Weight Ar rm is supplie d as a standar rd accessory.
In case of no need, rem move and keep p it in a safe place. p
Mount the W Weight Arm pinching p the holes h on right t and left side e of the base. Weight Arm m is spring lo oading type
wire and mo ount the Weig ght Arm by sl lightly wideni ing the openi ing. Mounti ing Holes are e located No. l, 2 and 3
positions. Tr ry effectivene ess of Weight t Arm and cho oose the mos st effective Ho ole Position.
M ount Weigh ht Arm by sl lightly wide ening it.
ment of Base e Plate of Tab ble 2.
- Adjustm
Position n of Base Plat te of Table 2 is adjustable back and for rth.
As facto ory default se etting, it is pla aced at 2rd ho ole (medium position).
General l Guidance:
Th hicker Paper:
In case fre equent slippag ge of paper is s observed, re emove Base P Plate Fixing Screws locat ed
both sides s of Table 2. .
Place the Base Plate for f Thicker s side of locati ion and fix th he
Th hinner Paper :
In case tw wo-stage fold ding is observ ved, remove Base Plate F Fixing Screw ws located bo oth
sides of Ta able 2.
Plac ce the Base Pl late for Thinn ner side of loc cation and fix x the Screws.
Page 52 of 57

Text on page 53
- Folding g Roller Pres ssure (Press Power) P Adju ustment
Folding g Pressure can n be set for 3 steps.
As facto ory default se etting, it is pla ace at mid. po osition.
Note:
Adjustment should be don ne after Pape er Feed Table is lifted at th he highest pos sition first.
Open C Cover for Tabl le 2 under Pap per Feed Tab ble.
Thicker Paper:
In case c higher fo olding pressur re is desired, remove Thum mb Screw and d push the Br racket so that t
Fol ding Roller Spring S gives h higher pressu ure to the Roll ler.
Left and d Right Settin ng should be
the same strengt h.
> Higher Pre essure. Thi icker Paper =>
Thinner Paper:
c paper is wrinkled, w rem move Thumb Screw and pu ull the Bracke ket so that Fol lding Roller In case
Spr ring gives low wer pressure t to the Roller. Left and R ight Setting s should be the same strengt th.
Thi nner Paper = > Lower Pres ssure
Page 53 of 57

Page 54 of 57

Page 55 of 57

Page 56 of 57

Page 57 of 57 ยท End of manual
Quick start
- Install the tables: Fit Table 1 to the main machine body and fix it with the Lock Levers on both sides. Raise the paper feed table to its highest point before installing or removing Table 2.
- Power on: Turn the Power Switch on and press the Feed Table Up/Down Key to place the Feed Table at its lowest position.
- Load the paper: Open the Top Cover, widen the Paper Guides and load the paper, fanned out and jogged well. The folder recognizes standard paper sizes automatically.
- Fit the side guides: Fit the Paper Side Guides along the paper edges and tighten the two thumb screws. Leave no gap between the leading edge of the paper and the Machine Front Stopper Wall.
- Set speed and start: Set the speed according to the paper quality and fold type, then press the TEST key or START key to start folding.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Paper skews in the folder | Gap between the paper leading edge and the Machine Front Stopper Wall | Use the Feed Table Skew Adjustment knob to remove the gap. Page 23 |
| Error code for paper left in the Paper Feed Sensor area | Paper left in the Paper Feed Sensor area, or the Paper Feed Sensor is dirty | Remove the paper or clean the sensor, then press the CLEAR/RESET key. Page 47 |
| Error code for paper left in the Paper Ejection Sensor area | Paper left in the Paper Ejection Sensor area, or the Paper Ejection Sensor is dirty | Remove the paper or clean the sensor, then press the CLEAR/RESET key. Page 47 |
| Error code for an open door or cover | The door of Table 2 is open, or the Top Cover is open | Close the door and the Top Cover, then press the CLEAR/RESET key. Page 47 |
| Double fed sheets detected | The ultrasonic sensor detected double fed sheets, so the machine stops | Remove the double fed sheets from the Output Paper Ejection Table and clear the error with the Clear/Reset key. Page 30 |
| Paper is out of the standard paper size | The folder cannot recognize the size automatically | Use Paper Length Manual Input Mode. Page 47 |
Frequently asked questions
What paper weights and sizes can the MBM 1800S fold?
It folds Bond 13.9 to 42.5 lbs, and Bond 42.5 to 61.1 lbs for single fold with limited paper. It automatically detects Letter, Legal and Ledger sizes. See page 8.
How fast is it and how much paper does it hold?
Folding speed is up to 18,000 sheets per hour (single fold, Letter), adjustable in 5 steps. Maximum capacity is 2.9", or 800 sheets, Bond 20 lbs. See page 8.
Which fold patterns are available?
Single, Letter, Zigzag, Double Parallel, Fold-out and Gate. It has 18 memories for standard fold patterns and 3 special memories for out of standard paper sizes. See page 8.
