MBM 207M Manual, page 1

Page 1 of 18

MBM 207M Manual, page 2

Page 2 of 18

MBM 207M Manual, page 3
Text on page 3

Safety Instructions

Definition of Symbols and Notes The following names and signs stand for possible dangers:

This symbol stands for immediate danger. Disregarding these instructions may cause severe injury.

This symbol stands for a potentially dangerous situation. Disregarding these instructions may lead to injuries or damage to property.

Danger

Make sure that the machine is electrically grounded to prevent electrical shock. Use the machine at 120 VAC with a frequency of 60Hz. There is a risk of electrical shock or fire if a higher or lower voltage is used, or if an electric current is utilized with a frequency not within the range stated above. Do not place any object on top of this machine. There is a risk of electrical shock or fire if water or any foreign object enters the machine. Handle the power cord with care. There is a risk of electrical shock or fire if the cord is damaged, broken, or placed under a heavy object. Do not insert or remove the power plug when water is present. Do not remove the cover of this machine. There is a risk of an electrical shock. Do not reconfigure the electronics of this machine. There is a risk of an electrical shock or fire. Do not operate the machine if it is emitting smoke or a strange odor. Turn off the machine, unplug from the outlet and contact your dealer. Do not operate the machine if the power cord is generating heat or emits a strange smell. Turn off the machine, unplug from the outlet and contact your dealer. If a foreign object enters into the machine, turn off the power switch and remove the power plug, then consult your dealer. In the event of a thunderstorm, unplug the machine.

Caution

Keep hair, clothing, and jewelry away from the machine while operating. Serious injury may result. Do not put the machine on an unstable or slanted surface. Doing so may cause the machine to drop or fall, causing damage and possible injury. Store and operate the machine in a clean, dust-free environment with low humidity. Avoid areas with high moisture, extreme temperatures and excessive dust, as these conditions may cause machine failure or electrical shock. Be sure to grasp the power cord by the plug when removing from the electrical outlet. Not doing so may cause damage to the cord and possible electrical shock or fire. Be sure to pull the power plug out of the electric outlet before moving the machine. Not doing so may cause damage to the cord and possible electrical shock or fire. Remove the power plug from the electrical outlet when this machine is not in use.

Page 3 of 18

MBM 207M Manual, page 4
Text on page 4

Introduction

Thank you for purchasing the MBM 207M Manual Paper Folder. You should receive many years of reliable service from this machine. Compact and easy to use, the 207M Paper Folder is sure to streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual thoroughly before using this machine.

Contents

  1. Specifications ............................................................................................................................ 4
  2. Accessories ................................................................................................................................ 5
  3. Description of Parts ................................................................................................................... 6
  4. Designation and Functions of Operation Panel ....................................................................... 7
  5. Preparations ............................................................................................................................... 8
  6. Operation Procedure.................................................................................................................. 9

Switching the Power ON ........................................................................................................ 9

Setting Fold Plate Position...................................................................................................... 9

Fold Feed Angle / Skew Adjustment..................................................................................... 10

Subtraction Counting ............................................................................................................ 10

Clearing a Paper Jam..............................................................................................................11

Cross Folding ........................................................................................................................ 12

Fine Adjustments for Table 1 ................................................................................................ 13

Fine Adjustments for Table 2 ................................................................................................ 14

  1. Maintenance (Cleaning and replacement of consumable items)............................................. 15

Page 4 of 18

MBM 207M Manual, page 5
Text on page 5
  1. Specifications

207M Manual Paper Folder

3.5” × 5” to 11” × 17” Smaller size for single fold only.

High- to medium-quality paper

Single, Letter, Zigzag, Double Parallel, and Fold-out. Cross-Fold.

Maximum Table 1: 13”

Table 2: 9 1 / 2 ”

Minimum Table 1: 2”

Table 2: 1 1 / 2 ”

Paper feed system Max. stacking capacity

500 sheets of 20# Bond

10,500 sheets/hr. (8.5 x 11, single fold)

Operation method

Available functions

Fold skew adjustment, paper jam detection, four digit counter, auxiliary paper guide for cross folding and Jam map indication.

Power consumption

Additional functions:

Paper jam detector Four-digit counter with addition/subtraction modes Auxiliary paper guide for cross fold

W 29 1 / 2 ” × D21 1 / 2 ” × H 21”(during use)

W 22” × D 21 1 / 2 ” × H 21”(during storage)

Page 5 of 18

MBM 207M Manual, page 6
Text on page 6
  1. Accessories

After un-boxing the 207M, make sure that the following accessories are present. Please contact your local dealer immediately if anything is missing.

Page 6 of 18

MBM 207M Manual, page 7
Text on page 7
  1. Description of Parts

Stopper plate

Fold position adjustment knob

Paper feed table lever

Page 7 of 18

MBM 207M Manual, page 8
Text on page 8
  1. Designation and Functions of Operation Panel

Performs test folding of two sheets.

Starts and stops machine.

Clears the counter / resets after an error.

Used for Subtraction counting.

Indicates the number of sheets folded.

Comes on when paper stock is depleted, or indicates the location of a mis-feed.

Page 8 of 18

MBM 207M Manual, page 9
Text on page 9
  1. Preparation

Install Table 1 and 2:

Insert Table 1 on the studs indicated by (a) and (b) as shown in

Insert Table 2 on the studs indicated by (c) and (d) as shown in

Note:

When setting Table 1, be sure to put its stopper plate at the center position.

Caution:

Be sure that both Table 1 and 2 fit correctly on the

studs (a), (b), (c) and (d). If they are improperly set, it may

cause an incorrect collation, or the tables may fall out of the machine.

Setting Paper:

Lift the auxiliary table and insert the paper.

Paper guide set screw

Raise the paper feed table lever.

Set the paper guide for the appropriate paper size.

Neatly stack the paper on the feed table with the printed

side facing up. (printed side down in case of fold-out)

Lower the paper feed table lever.

Paper feed table lever

Note:

If the paper does not come in contact with the paper feed roller, remove and reinsert.

Curled or wrinkled paper may not feed correctly.

When using printed paper, insure that the ink is completely dry, otherwise marking may occur.

Page 9 of 18

MBM 207M Manual, page 10
Text on page 10

Setting the paper exit roller: The exit roller should be moved to the proper position according to the paper size. Refer to the “Roller Position Indication” label. If ejection is not performed properly, try a different position.

Example:

Set the roller to position ONE when using 8 1 / 2 ” × 11” paper.

  1. Operation Procedure

Switch the Power to ON: Insert power plug into a proper outlet. Set the POWER switch to the ON position.

Note: Remove the power plug from the outlet after use.

Setting Fold Plate Table Position Pull the half-nut lever to move the stopper plate to the desired position on Table 1 and 2. Align the arrow on the stopper plate with the corresponding fold marks on the tables and release the half-nut. This locks the stopper plate into position.

Test Folding: Press the TEST key to feed two sheets of paper. Check to see if the paper has been folded correctly by inspecting the second of the two folded sheets.

If the fold position is not correct, refer to “Fine Adjustments” on pages 13& 14

Page 10 of 18

MBM 207M Manual, page 11
Text on page 11

Fold Feed Angle / Skew Adjustment: Turn the feed angle adjustment knob to the right if the lower side of the folded paper slants to the right. Turn the knob to the left of the lower side slants to the left.

Note: In cases other than single fold, put the folded paper face down on Table 1 to make a feed angle adjustment.

Continuous Folding:

Press the START/STOP key. The machine will fold the sheets

Press the START/STOP key again while the machine is in

operation in order to stop feeding.

Subtraction Counting: As each sheet is folded, the number indicated on the display decreases by one.

Press the appropriate numerical key to select the number of sheets to be folded.

Example: Press the number “10” key twice to select 20.

Note: The Subtraction counting number is cancelled when the POWER is set to OFF.

Page 11 of 18

MBM 207M Manual, page 12
Text on page 12

Under the following conditions the machine will automatically stop feeding:

(Press the CLEAR/RESET key to reset after an error has been corrected)

Indication on Control panel

When the START/STOP key is pressed when there is no stock.

When the START/STOP key is pressed while the paper feed lever is in the up position.

When stock runs out while folding in the Subtraction Counting Mode.

When a mis-feed occurs.

When paper jam occurs at Table 1 and Table 2.

When Roller cover is opened.

When paper stack (exit) table is full.

When paper jam occurs at the paper exit.

Clearing a Paper Jam:

Should a paper jam occur, set the POWER switch to the OFF position and remove the jammed sheet(s).

When the jammed paper is wrapped around the fold roller or other parts, it can be easily removed by

detaching Tables 1 and 2 from the unit.

Note:

When the roller cover is opened, the machine will automatically stop operation.

Page 12 of 18

MBM 207M Manual, page 13
Text on page 13

Cross Folding:

Cross folding refers to performing the double parallel, letter, or other types of folds on single-folded sheets of paper.

Example: 11” × 17” sheet is folded in half, and then cross-folded to letter size to fit into a standard # 10 envelope.

Note: The maximum weight of paper that can be used for cross folding is 28#.

However, the following variables may affect performance of the paper stock being folded: paper type, paper size, grain direction, printing quality, as well as the relative humidity and temperature of the operating environment.

On occasion, fold displacement may occur, causing a corner of the folded paper to be folded inside as indicated in the figure at the right. In these cases, additional fine adjustment may need to be made to the fold tables to eliminate the problem.

Tip: To aid in the cross-folding procedure, press the crease of the single-folded stock flat before attempting to cross fold.

Page 13 of 18

MBM 207M Manual, page 14
Text on page 14

Fine Adjustments for Table 1

Table 1 is not used

Double parallel fold

Fold-out Fold

Direction to turn the Table 1 fine adjustment knob

Page 14 of 18

MBM 207M Manual, page 15
Text on page 15

Fine Adjustments for Table 2

Double parallel fold

Direction to turn the Table 2 fine adjustment knob

Page 15 of 18

MBM 207M Manual, page 16
Text on page 16
  1. Maintenance

y Keep roller cover closed to prevent dust from accumulating on the rollers. y Clean the rollers regularly using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. y If paper dust or ink accumulates on the paper rollers or separator, the paper feeding function will deteriorate and may cause a paper jam or slipping. If this happens, clean them using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. y Remove any dirt on the exterior parts using alcohol or appropriate cleaner. Do not use solvents.

Two rollers can be removed and installed without using tools. These two can be easily cleaned along with the paper ejection photo sensor. As the other two rollers cannot be removed easily, they should be cleaned while slowly revolving them by hand. If only one sheet of paper is being fed, use a soft cotton swab to remove paper dust, etc. from the face of the paper ejection photo sensor shown by the arrow.

  1. Removing the rollers

Remove the upper roller in the order of 1 to 3, and then remove the lower roller.

1 Move down the roller setting lever to the OFF

position.

2 Slide the roller to the right. (Its shaft will come off from the left-side hole.)

3 Remove the roller from the right-side hole.

  1. Setting of the rollers

In the reverse order of removal, set the lower roller first. [1] Insert the roller deep to the right. [2] Slide the roller to the left.

  • Be careful not to let the roller shaft on both sides get stuck on Part A.

As shown above, the roller shaft should be placed on Part A. [3] Move up the roller setting lever to the ON position.

Caution! If the roller is not firmly fixed, it may cause operating problems. If it cannot be fixed, contact your dealer.

Page 16 of 18

MBM 207M Manual, page 17
Text on page 17

Replacing Paper Separator, Paper Feed Roller & Brake Rubber

When replacing the paper feed roller and paper separator, proceed in the order of (1) to (2).

Grasp the paper separator (with plastic part) at both ends and pull it out. To install, reverse the procedure.

To order the parts above, please contact your dealer.

Page 17 of 18

MBM 207M Manual, page 18
Text on page 18
  1. Troubleshooting

The paper does not feed properly

The machine does not operate even after the START/STOP key is pressed

Recently printed paper sticks together

Jog the paper sufficiently. Make sure that the ink is dry.

Stains on the paper separator

Clean the paper feed separator using appropriate cleaner.

Stains on the paper feed rubber roller

Clean the dust or ink on the paper feed roller using appropriate cleaner.

The paper separator is worn out

Install a new paper separator.

The volume of the paper stacked on the paper feed table is not enough

Add more paper to the feed table – at least 20 sheets or more.

Paper jam inside the unit

Detach Table 1 and 2 and remove the jammed paper from the unit.

Recently printed paper sticks together

Jog the paper sufficiently. Make sure that the ink is dry.

Stains on the paper separator

Clean the paper separator using an appropriate cleaner.

Stains on the paper feed roller

Clean the dust or ink on the paper feed roller using an appropriate cleaner.

Stains on paper fold rollers

Clean all four fold rollers using an appropriate cleaner.

Tables 1 and 2 are not properly set

Paper jam in Table 1 and 2

Detach Table 1 and 2 and remove the jammed paper.

The length of the paper is not standard size

Measure the length of the paper and adjust using the fine adjustment knob.

The surfaces of the fold rollers are covered with dust or ink, causing them to be slippery

Clean all four fold rollers using an appropriate cleaner.

Operate the machine in a climate-controlled environment. Paper should be at room temperature before folding. Paper stored below 53F is not recommended.

Wrinkles appear on the paper

Improper fold position

Printed paper (13# or lighter) cannot be folded

Page 18 of 18 ยท End of manual

Quick start

  1. Install the tables: Insert Table 1 on studs (a) and (b) and Table 2 on studs (c) and (d). Put the stopper plate of Table 1 at the center position.
  2. Load the paper: Lift the auxiliary table, raise the paper feed table lever, set the paper guide to the paper size, stack the paper printed side up and lower the lever.
  3. Set the exit roller: Move the paper exit roller according to the Roller Position Indication label. Use position ONE for 8 1/2 x 11 paper.
  4. Power on and set the fold: Plug in the machine and set the POWER switch to ON. Pull the half-nut lever, move the stopper plate and align its arrow with the fold marks.
  5. Test and run: Press the TEST key to feed two sheets and check the second one. Press START/STOP to fold continuously.

Troubleshooting

ProblemLikely causeFix (from the manual)
Paper does not feed properlyStains on the paper separator or the paper feed rubber rollerClean the separator and the feed roller with an appropriate cleaner. Page 18
Recently printed paper sticks togetherPaper is not separated or the ink is not dryJog the paper sufficiently and make sure the ink is dry. Page 18
Machine does not feed with a small stackNot enough paper on the feed tableAdd more paper, at least 20 sheets or more. Page 18
Paper jam inside the unitPaper jam in Table 1 and 2Detach Table 1 and 2 and remove the jammed paper. Page 18
Fold is off on non-standard paperThe length of the paper is not a standard sizeMeasure the length of the paper and adjust using the fine adjustment knob. Page 18
Paper slips or wrinklesFold roller surfaces are covered with dust or inkClean all four fold rollers using an appropriate cleaner. Paper should be at room temperature, and paper stored below 53F is not recommended. Page 18

Frequently asked questions

How do I clear a paper jam?

Set the POWER switch to OFF and remove the jammed sheets. If paper is wrapped around the fold roller, detach Tables 1 and 2 to remove it. See page 12.

How do I clean the rollers?

Clean the rollers regularly using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. See page 16.

When does the machine stop feeding by itself?

It stops for conditions such as no stock, a mis-feed, a paper jam, an open roller cover or a full stack table. Press the CLEAR/RESET key after correcting the error. See page 12.

What power does the 207M need?

It must be electrically grounded and used at 120 VAC with a frequency of 60Hz. See page 3.