

Page 1 of 25

Text on page 2
OPERATION MANUAL
MBM 208J
MANUAL FOLDER
Page 2 of 25

Page 3 of 25

Text on page 4
Safety Instructions
Definition of Symbols and Notes The following names and signs stand for possible dangers:
This symbol stands for immediate danger. Disregarding these instructions may cause severe injury.
This symbol stands for a potentially dangerous situation. Disregarding these instructions may lead to injuries or damage to property.
Danger
Make sure that the machine is electrically grounded to prevent electrical shock.
Use the machine at 100-240 VAC with a frequency of 50-60Hz. There is a risk of electrical
shock or fire if a higher or lower voltage is used, or if an electric current is utilized with a
frequency not within the range stated above.
Do not place any object on top of this machine. There is a risk of electrical shock or fire if water
or any foreign object enters the machine.
Handle the power cord with care. There is a risk of electrical shock or fire if the cord is
damaged, broken, or placed under a heavy object.
Do not insert or remove the power plug when water is present.
Do not remove the cover of this machine. There is a risk of an electrical shock.
Do not reconfigure the electronics of this machine. There is a risk of an electrical shock or fire.
Do not operate the machine if it is emitting smoke or a strange odor. Turn off the machine,
unplug from the outlet and contact your dealer.
Do not operate the machine if the power cord is generating heat or emits a strange smell. Turn
off the machine, unplug from the outlet and contact your dealer.
If a foreign object enters into the machine, turn off the power switch and remove the power
plug, then consult your dealer.
In the event of a thunderstorm, unplug the machine.
Caution
Keep hair, clothing, and jewelry away from the machine while operating. Serious injury may
Do not put the machine on an unstable or slanted surface. Doing so may cause the machine to
drop or fall, causing damage and possible injury.
Store and operate the machine in a clean, dust-free environment with low humidity. Avoid areas
with high moisture, extreme temperatures and excessive dust, as these conditions may cause
machine failure or electrical shock.
Be sure to grasp the power cord by the plug when removing from the electrical outlet. Not doing
so may cause damage to the cord and possible electrical shock or fire.
Be sure to pull the power plug out of the electric outlet before moving the machine. Not doing so
may cause damage to the cord and possible electrical shock or fire.
Remove the power plug from the electrical outlet when this machine is not in use.
Page 4 of 25

Page 5 of 25

Text on page 6
Introduction
Thank you for purchasing the EZF-200 Manual Paper Folder. You should receive many years of reliable service from this machine. Compact and easy to use, the EZF-200 Paper Folder is sure to streamline your paper folding tasks, saving you valuable time. Please read the Operation Manual thoroughly before using this machine.
Contents
- Accessories .................................................................................................................................. 4
- Description of Parts ..................................................................................................................... 5
- Designation and Functions of Operation Panel ........................................................................ 6
- Preparations ................................................................................................................................. 7
- Operation Procedure ................................................................................................................... 8
Switching the Power ON ........................................................................................... 8
Setting Fold Plate Position ......................................................................................... 8
Test Folding ............................................................................................................... 8
Fold Feed Angle / Skew Adjustment ......................................................................... 9
Continuous Folding ................................................................................................... 9
Subtraction Counting ................................................................................................. 9
Cross Folding ........................................................................................................... 10
Fine Adjustments for Table 1 .................................................................................... 11
Fine Adjustments for Table 2 ................................................................................... 12
Speed adjustment ..................................................................................................... 13
Functions that can be set .......................................................................................... 14
Interval function (batch processing) ........................................................................ 15
Error indications, situations, and measures .................................................. 16
- Maintenance (Cleaning and replacement of consumable items) .............................................. 17
- Trouble shooting ....................................................................................................................... 18
- Specifications ............................................................................................................................ 19
Page 6 of 25

Text on page 7
- Accessories
After un-boxing the EZF-200, make sure that the following accessories are present. Please contact your local dealer immediately if anything is missing.
Page 7 of 25

Text on page 8
- Description of Parts
Fold position adjustment knob
Paper feed table lever
Page 8 of 25

Text on page 9
- Designation and Functions of Operation Panel
Performs test folding of two sheets.
Starts and stops machine.
Clears the counter / resets after an error.
Used for Subtraction counting.
Indicates the number of sheets folded.
Comes on when paper stock is depleted, or indicates the location of a miss-feed.
Adjust the speed using the “+” and “-” keys.
Page 9 of 25

Text on page 10
- Preparation
Install Table 1 and 2:
Insert Table 1 on the studs indicated by (a) and (b) as shown in
Insert Table 2 on the studs indicated by (c) and (d) as shown in
Note:
When setting Table 1, be sure to put its stopper plate at the center position.
Caution:
Be sure that both Table 1 and 2 fit correctly on the
studs (a), (b), (c) and (d). If they are improperly set, it may
cause an incorrect collation, or the tables may fall out of the machine.
Setting Paper:
Lift the auxiliary table and insert the paper.
Raise the paper feed table lever.
Set the paper guide for the appropriate paper size.
Neatly stack the paper on the feed table with the printed
side facing up. (printed side down in case of fold-out)
Lower the paper feed table lever.
Note:
If the paper does not come in contact with the paper feed roller, remove and reinsert.
Curled or wrinkled paper may not feed correctly.
When using printed paper, insure that the ink is completely dry, otherwise marking may occur.
Page 10 of 25

Text on page 11
Setting the paper exit roller:
The exit roller should be moved to the proper position according
to the paper size. Refer to the “Roller Position Indication” label.
If ejection is not performed properly, try a different position.
Example:
Set the roller to position ONE when using A3 paper.
Roller position indication label
- Operation Procedure
5.1 Switch the Power to ON
Insert power plug into a proper outlet.
Set the POWER switch to the ON position.
Note:
Remove the power plug from the outlet after use.
5.2 Setting Fold Plate Table Position
Pull the half-nut lever to move the stopper plate to the
desired position on Table 1 and 2. Align the arrow on the
stopper plate with the corresponding fold marks on the
tables and release the half-nut. This locks the stopper plate
Press the TEST key to feed two sheets of paper.
Check to see if the paper has been folded correctly by inspecting
the second sheet of the two folded.
If the fold position is not correct:
- Fold Position Adjustment (Fold Length)
Refer page 13 & 14 “Fine Adjustment for table 1 and 2”.
- Skew Adjustment (Slant or Paper is not square)
Refer page 10 “Fold Feed Angle / Skew Adjustment”.
Page 11 of 25

Text on page 12
5.4 Fold Feed Angle / Skew Adjustment
Watch the folded paper ejected from the machine as ejected and refer the chart below. Turn feed adjustment knob right or left to adjust skew.
Folding Pattern
Arrow shows direction of sheet ejected to stacking tray
Direction of Feed Adjustment Knob Folding Pattern
Arrow shows direction of sheet ejected to stacking tray
Direction of Feed Adjustment Knob
5.5 Continuous Folding:
Press the START/STOP key. The machine will fold the sheets
Press the START/STOP key again while the machine is in
operation in order to stop feeding.
5.6 Subtraction Counting:
As each sheet is folded, the number indicated on the display
Press the appropriate numerical key to select the number of
sheets to be folded.
Example:
Press the number “10” key twice to select 20.
Note:
The Subtraction counting number is cancelled when the POWER
is set to OFF.
Page 12 of 25

Text on page 13
5.7Cross Folding (Re-Folding):
Cross folding refers to performing the double parallel, letter, or other
types of folds on single-folded sheets of paper.
Note:
The maximum weight of paper that can be used for cross folding is
However, the following variables may affect performance of the paper
stock being folded: paper type, paper size, grain direction, printing
quality, as well as the relative humidity and temperature of the operating
On occasion, fold displacement may occur, causing a corner of the
folded paper to be folded inside as indicated in the figure at the right. In
these cases, additional fine adjustment may need to be made to the fold
tables to eliminate the problem.
Tip:
To aid in the cross-folding procedure, press the crease of the
single-folded stock flat before attempting to cross fold.
Page 13 of 25

Text on page 14
5.8 Fine Adjustments for Table 1
Table 1 is not used
Double parallel fold
Fold-out Fold
Direction to turn the Table 1 fine adjustment knob
Page 14 of 25

Text on page 15
5.9 Fine Adjustments for Table 2
Double parallel fold
Direction to turn the Table 2 fine adjustment knob
Page 15 of 25

Text on page 16
In the following cases, try to adjust the speed:
・If wrinkles appears or skews occur to sheets of soft paper such as groundwood paper, reduce the speed.
・To reduce the operating sound, reduce the speed.
・When sheets of thick paper jam, increase the speed.
Adjust the speed using the “+” and “-” keys.
The speed is displayed on the counter.
Select low speed when folding soft sheets of paper or reducing the operating sound.
Select high speed when folding sheets of thick paper.
When the “MODE” key is pressed and the SPECIAL indicator lamp is lit, the machine enters SPECIAL mode.
Three speed levels can be selected as in the abovementioned case.
S_LO
S_ME
The machine operates in a silent manner. This mode is not suitable for sheets of thick
Dedicated mode for sheets of thick paper.
S_HI
The machine can perform folding work at high speed. Sheets of paper of A4 and smaller
sizes can be folded only in two, inward three, and four.
・After the speed was changed, it is necessary to make a fine adjustment of the folding position.
Page 16 of 25

Text on page 17
5.11 Functions that can be set In this mode, the “interval function (patch processing),” “operation memory,” and “operating sound enabled/disabled” can be set.
Hold down the “MODE” key. “ rb” will be displayed on the seven-segment LED display. The functions (settings) are enabled when each digit is lit, or they are disabled when each digit is flickering. Each function can be enabled or disabled by pressing the corresponding key. The settings will be determined by releasing the “MODE” key.
Displayed character
Corresponding Description key 1000 See “5.9 Interval function.”
Operation memory setting
Operating sound enabled/disabled
Details of the operation performed just before the power is turned off will be saved. The operation saved on the preceding day can be performed as soon as the power is turned on. The sound produced when a button is pressed and beeps, such as the operation end sound, can be muted.
Page 17 of 25

Text on page 18
5.12 Interval function (batch processing) The interval function sections the folding operation at each set time. Select the interval function in the operation of “5.8 Functions that can be set.”
Method of switching the screen The screen switches by pressing the “1000” key. (Setting check → Sheet count setting → Waiting time setting →Setting check ・・・)
[Sheet count setting] Enter the number of sheets to be folded in succession (sheet count). Up to 500 sheets of paper can be set.
[Waiting time setting] Enter the waiting time (seconds) after successive folding. Up to 20 seconds can be set.
[Setting Check] Before starting the folding operation, check the sheet count and waiting time settings on this screen.
- To cancel the interval, flicker “i” by pressing the “MODE” and “1000” keys together.
Page 18 of 25

Text on page 19
5.13 Error indications, situations, and measures
The machine will automatically stop in the following cases
① The Start/Stop key was pressed ①Set sheets of paper. without sheets of paper.
②The Start/Stop key or the Test key ②Shift down the paper feed table was pressed with the paper feed lever. table lever shifted up.
③ Sheets of paper ran out in the ③Add sheets of paper. middle of operation in countdown mode.
①A paper feed slip occurred.
①Clean or replace the paper separator and the paper feed rubber rollers. See “6 maintenance” on
②A paper jam occurred in folding ②Detach folding cassette 1 or 2, and remove the jammed paper. cassette 1 or 2
①The paper ejection table is full of ①Remove the sheets of paper in the sheets of paper. paper ejection unit.
②A paper jam occurred in the paper ②Remove the jammed paper. ejection unit. ③Clean the paper ejection ③The paper ejection photosensor is photosensor. contaminated. See “6 maintenance” on page 15
①The safety cover is open.
①Close the safety cover.
②Folding cassette 1 is not properly ②Reset folding cassette 1. set.
③Folding cassette 2 is not properly ③Reset folding cassette 2. set.
①A paper jam occurred in folding ①Detach folding cassette 1 or 2, and cassette 1 or 2. remove the jammed paper.
②The speed is low. ②Increase the speed. A paper jam occurred due to a low speed.?
Page 19 of 25

Text on page 20
- Maintenance ( Cleaning and replacement of consumable items )
Keep roller cover closed to prevent dust from accumulating on the rollers. Clean the rollers regularly using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. If paper dust or ink accumulates on the paper rollers or separator, the paper feeding function will deteriorate and may cause a paper jam or slipping. If this happens, clean them using a cleaner suitable for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. Remove any dirt on the exterior parts using alcohol or appropriate cleaner. Do not use solvents.
Two rollers can be removed and installed without using tools. These two can be easily cleaned along with the paper ejection photo sensor. As the other two rollers cannot be removed, they should be cleaned while slowly revolving them by hand. If only one sheet of paper is being fed, use a soft cotton swab to remove paper dust, etc. from the face of the paper ejection photo sensor shown by the arrow.
- Removing the rollers
Remove the upper roller in the order of 1 to 3, and then remove the lower roller.
1 Move down the roller setting lever to the OFF position.
2 Slide the roller to the right. (Its shaft will come off from the left-side hole.)
3 Remove the roller from the right-side hole.
- Setting of the rollers
In the reverse order of removal, set the lower roller first. [1] Insert the roller deep to the right. [2] Slide the roller to the left.
- Be careful not to let the roller shaft on both sides get stuck on Part A.
As shown above, the roller shaft should be placed on Part A. [3] Move up the roller setting lever to the ON position.
Caution! If the roller is not firmly fixed, it may cause operating problems. If it cannot be fixed, contact your dealer.
Page 20 of 25

Text on page 21
- Troubleshooting
The paper does not feed properly
The machine does not operate even after the START/STOP key is pressed
Wrinkles appear on the paper
Improper fold position
Printed paper (13 lbs bond lighter) is not folded.
Recently printed paper sticks together
Jog the paper sufficiently. Make sure that the ink is dry.
Stains on the paper separator
Clean the paper feed separator using appropriate cleaner.
Stains on the paper feed rubber roller
Clean the dust or ink on the paper feed roller using appropriate cleaner.
The paper separator is worn out
Install a new paper separator.
The volume of the paper stacked on the paper feed table is not enough
Add more paper to the feed table – at least 20 sheets or more.
Paper jam inside the unit
Detach Table 1 and 2 and remove the jammed paper from the unit.
Recently printed paper sticks together
Jog the paper sufficiently. Make sure that the ink is dry.
Stains on the paper separator
Clean the paper separator using an appropriate cleaner.
Stains on the paper feed roller
Clean the dust or ink on the paper feed roller using an appropriate cleaner.
Stains on paper fold rollers
Clean all four fold rollers using an appropriate cleaner.
Tables 1 and 2 are not properly set
Paper jam in Table 1 and 2
Detach Table 1 and 2 and remove the jammed paper.
The length of the paper is not standard size
Measure the length of the paper and adjust using the fine adjustment knob.
The surfaces of the fold rollers are covered with dust or ink, causing them to be slippery
Clean all four fold rollers using an appropriate cleaner.
Operate the machine in a climate-controlled environment. Paper should be at room temperature before folding. Paper stored below 53F is not recommended.
Page 21 of 25

Text on page 22
- Specifications
Smallest size for single fold only.
High- to medium-quality paper
Up to 210 g/㎡ bond for Single Fold only.
Up to 104.7 g/㎡ for Cross-Fold(Re-Fold)
・Single, Letter, Zigzag, Double Parallel, Fold Out, Gate
Maximum Table 1: 13” Table 2: 9 1 / 2 ”
Minimum Table 1: 2” Table 2: 1 1 / 2 ”
Paper feed system Max. stacking capacity
500 sheets of 20# Bond
2,400 – 144,00 sheets/h (8.5 x 11, single fold)
Three-roller friction feed/separation system
Available functions
Fold skew adjustment, fold length adjustment, paper jam detection, four digit counter(addition/subtraction), test fold, auxiliary paper guide for cross-folding(re-folding) and Jam map indication.
Power consumption
W 18” × D 21 / 2 ” × H 13” (during storage)
Page 22 of 25

Page 23 of 25

Page 24 of 25

Page 25 of 25 ยท End of manual
Quick start
- Set up safely: Put the machine on a stable, level surface in a clean, dry area. Plug it into a grounded outlet rated 100-240 VAC, 50-60 Hz.
- Prepare the paper: Let paper reach room temperature before folding. Jog the sheets well and make sure printed ink is dry.
- Check the cassettes and cover: Close the safety cover and make sure folding cassettes 1 and 2 are set properly.
- Load the paper: Shift the paper feed table lever down. Put at least 20 sheets on the feed table.
- Run a test fold: Run a test fold first and check the fold position.
- Adjust if needed: If the paper is not a standard length, measure it and use the fine adjustment knob. If jams happen at a low speed, increase the speed.
- Start folding: Press the Start/Stop key to run. Keep the roller cover closed to keep dust off the rollers.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine stops after the Start/Stop key is pressed with no paper | There are no sheets on the feed table. | Set sheets of paper on the feed table. Add sheets if they run out during a countdown run. Page 19 |
| Machine stops when Start/Stop or Test is pressed | The paper feed table lever is shifted up. | Shift the paper feed table lever down. Page 19 |
| Paper feed slip | The paper separator or paper feed rubber rollers are dirty or worn. | Clean or replace the paper separator and the feed rubber rollers. Use a cleaner made for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. Page 19 |
| Paper jam in folding cassette 1 or 2 | Paper is stuck in a folding cassette. A low speed can also cause a jam. | Detach folding cassette 1 or 2 and remove the jammed paper. Increase the speed if low speed caused it. Page 19 |
| Paper ejection table is full, jams, or the photosensor is dirty | Sheets have piled up in the ejection unit, a sheet has jammed, or the ejection photosensor has dirt on it. | Remove the sheets from the paper ejection unit. Remove any jammed paper. Clean the ejection photosensor with a soft cotton swab. Page 19 |
| Safety cover open or folding cassette not set | The safety cover is open, or folding cassette 1 or 2 is not set properly. | Close the safety cover. Reset folding cassette 1 or 2. Page 19 |
| Paper does not feed properly | Freshly printed sheets stick together, the separator or feed roller is stained, the separator is worn, or too few sheets are on the feed table. | Jog the paper well and make sure the ink is dry. Clean the separator and feed roller. Install a new separator if worn. Put at least 20 sheets on the feed table. Page 21 |
Frequently asked questions
How many sheets do I need on the feed table?
Put at least 20 sheets on the paper feed table. Too little paper can cause feeding problems. See page 21.
How should I clean the rollers?
Use a cleaner made for rubber rollers or a cloth slightly dampened with water. Do not use solvents or aerosol sprays. See page 20.
What paper temperature is best?
Paper should be at room temperature before folding. Paper stored below 53F is not recommended. See page 21.
What power does the 208J need?
It must be grounded and run at 100-240 VAC with a frequency of 50-60 Hz. See page 4.
What if the machine gives off smoke or a strange smell?
Stop using it. Turn it off, unplug it from the outlet and contact your dealer. See page 4.
