MBM 25 Drill Manual, page 1

Page 1 of 9

MBM 25 Drill Manual, page 2
Text on page 2

VS-15 / VS-25

OPERATION MANUAL

Use the machine properly after reading the "Safety Instructions" given below carefully. These safety instructions are given to ensure that the machine will be used safely and properly and to prevent operators from sustaining harm and injuries.

UCHIDA YOKO CO., LTD., TOKYO, JAPAN

Page 2 of 9

MBM 25 Drill Manual, page 3
Text on page 3

SAFETY INSTRUCTIONS

Definition of Symbols and Notes In this manual following names and signs stand for possible dangers.

Danger

This symbol stands for immediate danger threatening the life and health of persons. Disregarding these instructions may cause severe damage to health and even serious injuries.

Caution

This symbol stands for an endangering situation that may occur. Disregarding these instructions may lead to slight injuries or damage to property.

Explanations of the illustrations used in the Safety Instructions are given as follows:

Danger

  1. Don't put a hand under the hollow drill bit. There is a danger of receiving an injury.
  2. Don't touch any rotating part. There is a danger of receiving an injury.
  3. Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of the machine. There is a danger of receiving an injury.
  4. When you change into unusual states, like smoke comes out, please turn off the power switch of a main part, and pull out a power supply plug from a wall socket after that. There are failure, a fire, and fear of an electric shock.

Caution

  1. Please do not install a machine in the unstable place to which it is shaky or leans. There is a danger of receiving an injury.
  2. When you move, have a base. There is a danger of receiving an injury.
  3. When you install a machine, please install to a place with no dust, and the place which is not influenced with a liquid. It becomes the cause of failure if the installation method is mistaken.
  4. Turn off the power supply beforehand when attaching or detaching hollow drill bits. There is a danger of receiving an injury.
  5. Don't touch the blade point of the hollow drill bit. There is a danger of receiving an injury.
  6. The hollow drill bits become heated when they are drilling. Don't touch them when they are drilling. Touching them may cause a burn.
  7. Please do not make a hole in paper with foreign substances, such as a needle of a stapling machine. Moreover, also things other than paper. There is a danger of receiving an injury.
  8. Please do not make a hole hard paper and near the hole which have opened in piles. There is a danger of receiving an injury.
  9. Turn off the power supply beforehand when adjusting the fiber plug. There is a danger of receiving an injury.
  10. When a machine stopped during use, turn off the power switch, and pull out a power supply plug from a wall socket after that. There is a danger of begins to turn again. And there is a danger of receiving an injury.

Page 3 of 9

MBM 25 Drill Manual, page 4
Text on page 4

Introduction

Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety Instructions" (page 1) to ensure that the machine will be used properly.

Keep the manual at an appointed place with care so that it may be accessible whenever necessary.

The specifications of this product are subject to change for improvement. Therefore, don't mistake the "Operation Manual" of one product of the same model for that of another because descriptions in the "Operation Manual" of products of the same model may differ.

1. Before use

(1) Check the kinds and quantities of accessories

Page 4 of 9

MBM 25 Drill Manual, page 5
Text on page 5

Clutch stopper handle

Upper lever Lower lever

Up to unclamp

Down to unclamp

Paper guide Centering scale

Back margin adjusting bolt

Page 5 of 9

MBM 25 Drill Manual, page 6
Text on page 6

2. Operating instructions

(1) Checks before setting

Caution

Please do not install a machine in the unstable place to which shaky or leans. There is a danger of receiving an injury.

When you move, have a base. There is a danger of receiving an injury.

When you install a machine, please install to a place with no dust, and the place which is not influenced with a liquid. It becomes the cause of failure if the installation method is mistaken.

Caution

Don't put a hand under the hollow drill bit. receiving an injury.

There is a danger of

Turn off the power supply beforehand when attaching or detaching hollow drill bits. There is a danger of receiving an injury.

Don't touch the blade point of the hollow drill bit. There is a danger of receiving an injury.

  1. Setting a drill bit Insert a drill bit into the chuck and tighten with the provided wrench.
  2. Setting the punch depth After installing a drill bit, adjust the stop nut that limits downward travel so that the drill bit just enters the brown fiber plug on the table when the drill bit is fully extended.
  3. Setting paper Open the paper guide and place the paper on the table. Close the paper guide the paper will be centered on the table automatically. Push down both sides of the paper clamp to secure the paper. Clamping pressure should be set according to the type of the paper. VS-15: Do not try to punch more than 30mm of paper. VS-25: Do not try to punch more than 50mm of paper.

Page 6 of 9

MBM 25 Drill Manual, page 7
Text on page 7
  1. Setting the back margin (Distance between the edge of the paper and the center of the holes) The back margin can be set at any value from 6mm to 35mm by turning the back margin adjusting bolt (use the scale on the table as a guide).
  2. Distance of the holes The program pitch bar can be set to select any of six pitches. Continuous punching can be done precisely thanks to proper paper setting by the clutch stopper.

Caution

Don't put a hand under the hollow drill bit. receiving an injury.

Don't touch any rotating part. injury.

There is a danger of

There is a danger of receiving an

Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of the machine. There is a danger of receiving an injury. When you change into unusual states, like smoke comes out, please turn off the power switch of a main part, and pull out a power supply plug from a wall socket after that. There are failure, a fire, and fear of an electric shock. The hollow drill bits become heated when they are drilling. Don't touch them when they are drilling. Touching them may cause a burn.

Don't touch the blade point of the hollow drill bit. There is a danger of receiving an injury.

Please do not make a hole in paper with foreign substances, such as a needle of a stapling machine. Moreover, also things other than paper. There is a danger of receiving an injury.

Please do not make a hole hard paper and near the hole which have opened in piles. There is a danger of receiving an injury.

(6) Operating the punch Turn on the power then lower the drill bit quickly without stopping until the stop nut halts the descent (this should take about one second)

(7) Finishing the punch After the punch finished, turn off the power. Take paper after the rotation of a drill bit completely stopped.

3. Maintenance

(1) Checking the edge of the drill bit

If punching requires more force than normally or if the drill bit lifts paper with it, it's time to sharpen the drill bit. It's a good idea to sharpen the drill bit regularly, before this happens.

  1. Sharpening the drill bit

A dull drill bit may make punching hard. A dull drill bit is more easily damaged than a sharp one. To sharpen it, follow these steps:

Page 7 of 9

MBM 25 Drill Manual, page 8
Text on page 8

Caution

Don't put a hand under the hollow drill bit. receiving an injury.

Don't touch any rotating part. injury.

There is a danger of

There is a danger of receiving an

Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of the machine. There is a danger of receiving an injury.

Don't touch the blade point of the hollow drill bit. There is a danger of receiving an injury.

  1. Place the provided sharpener on the fiber plug as shown at the right, and turn on the power.
  2. Turn the handle until the rotating drill bit touches the sharpener, then turn a little more. The drill bit is sufficiently sharp when you hear a high-pitched squeal.
  3. Remove the burrs on the edge, by holding the provided oilstone parallel to the rotating drill bit and bringing then in to contact until all burrs are gone.
  4. Use the paraffin to the drill bit for lubrication.

Bring the dull drill bit down onto the sharpener.

Hold the oilstone parallel to the drill bit as you remove burrs.

  1. If bottom sheets are not completely punched

The fiber plug wears out with continued use. When the bottom sheets are not punched completely, turn the fiber plug over or turn it 180°; replace as necessary.

Caution

Turn off the power supply beforehand when adjusting the fiber plug. There is a danger of receiving an injury.

  1. Emptying the chip receptacle

The tiny paper disks (chips) that are punched out of the paper travel up through the hollow drill bit and accumulate in the chip receptacle. Empty the receptacle often, before it becomes full. To remove the receptacle, simply lift it out of the machine. After emptying, make sure you seat it securely again.

Page 8 of 9

MBM 25 Drill Manual, page 9
Text on page 9
  1. When thermal protector works

Caution

When a machine stopped during use, turn off the power switch, and pull out a power supply plug from a wall socket after that. There is a danger of begins to turn again. And there is a danger of receiving an injury. When machine use long hours, motor becomes hot. To avoid the damaging of the motor, rotation

of drill automatically stops by activating of thermal protector.

When machine become cold, drill

automatically rotates again if machine switch is not turned off.

This might be cause of the injure of

operator. So, when thermal protector works, turn off the power switch and pull out the power supply

  1. Product specifications

Diameter of drill bit

376mm Automatic centering

4/5/5.5/6/6.5mm (4mm: Optional adapter is required) 6 to 35mm (normal) 12.5 to 35 (4mm drill bit) 376mm Automatic centering

W480 x D260 mm

W480 x D260 mm

W480 x D340 x H430 mm

W480 x D340 x H470 mm

5 Ordering consumables, etc.

When ordering consumables or parts such as fiber plug, specify the machine model.

Keep this “Operation Manual” at an appointed place with care so that it may be available whenever required. If this “Operation Manual” is stained or lost, make contact with the distributor or our salesman or customer service section to ask for a new operation manual after making sure of its contents. When transmitting this product to another person, be sure to attach this “Operation Manual” to the product.

UCHIDA YOKO CO., LTD.

9-15, Shiomi 2-chome, Koto-ku, Tokyo, Japan

Page 9 of 9 ยท End of manual

Quick start

  1. Fit the drill bit: Turn off the power. Insert the drill bit into the chuck and tighten it with the provided wrench.
  2. Set the punch depth: Adjust the stop nut so the bit just enters the brown fiber plug on the table when fully lowered.
  3. Load the paper: Open the paper guide, place the paper on the table and close the guide to center it. Push down both sides of the paper clamp. VS-15 punches up to 30mm and VS-25 up to 50mm.
  4. Set the back margin: Turn the back margin adjusting bolt. Any value from 6mm to 35mm can be set. Use the scale on the table.
  5. Set the hole distance: Choose one of six pitches with the program pitch bar.
  6. Punch: Turn on the power. Lower the drill bit quickly without stopping until the stop nut halts it. This takes about one second.
  7. Finish: Turn off the power. Take the paper out only after the bit has fully stopped.

Troubleshooting

ProblemLikely causeFix (from the manual)
Punching takes more force or the bit lifts the paperThe drill bit is dull.Sharpen the drill bit. It is best to sharpen it regularly before this happens. Page 7
Drill bit goes too deep or not deep enoughThe punch depth is not set right.Adjust the stop nut so the bit just enters the brown fiber plug when fully lowered. Page 6
Drill stops during long useThe motor got hot and the thermal protector stopped the drill.Turn off the power switch and unplug the machine. The drill can start turning again by itself when it cools if the switch is left on. Page 9
Smoke or other unusual signsSomething is wrong with the machine.Turn off the main power switch and pull the plug from the wall socket. Page 7
Machine stopped during useThe machine may turn again without warning.Turn off the power switch and pull the plug from the wall socket. Page 3
Risk of injury when punchingForeign objects, hard paper, or holes too close to an existing hole.Do not punch paper with staples or other objects, hard paper, or near holes already made. Page 7

Frequently asked questions

How much paper can the drill punch at once?

The VS-15 punches up to 30mm of paper. The VS-25 punches up to 50mm. See page 6.

What back margin can I set?

Any value from 6mm to 35mm, using the back margin adjusting bolt and the table scale. See page 7.

How do I know when to sharpen the drill bit?

Sharpen it when punching needs more force than normal or the bit lifts paper with it. Regular sharpening is a good idea. See page 7.

What drill bit sizes are listed?

The specifications list 4, 5, 5.5, 6 and 6.5mm. The 4mm size needs an optional adapter. See page 9.

What is the thermal protector?

It stops the drill when a long run makes the motor hot. Turn off the power switch and unplug the machine when it works. See page 9.