Use machine only after reading the "Safety Instructions" given below carefully. These safety instructions are given to ensure that the machine will be used safely and properly and to prevent operators from sustaining harm and injuries.

SAFETY INSTRUCTIONS

Definition of Symbols and Notes In this manual the following names and signs stand for possible dangers.

Danger This symbol stands for immediate danger threatening the life and health of persons. Disregarding these instructions may cause severe damage to health and even serious injuries.

Caution This symbol stands for an endangering situation that may occur. Disregarding these instructions may lead to slight injuries or damage to property.

Note This symbol stands for notes, operational hints, and other useful information. They are convenient for exploiting the machine’s functional abilities.

SAFETY INSTRUCTIONS

Explanations of the illustrations used in the Safety Instructions are given as follows:

Danger

1. Don't open the cover of the equipment.

There is a danger of receiving an injury

2. Turn off the power supply beforehand when attaching or detaching the

There is a danger of receiving an injury.

3. Don't touch any rotating part.

There is a danger of receiving an injury.

Caution

1. Don't put a hand into the cover or a clearance between parts. There is a danger of receiving an injury.
2. Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of the machine. There is a danger of receiving an injury.
3. Don't touch the blade point of the cutter. There is a danger of receiving an injury.
4. Don't touch the blade point of the perforating blade. There is a danger of receiving an injury.
5. Turn off the power supply beforehand when setting the feed table.

There is a danger of receiving an injury.

6. Turn off the power supply beforehand when setting the stacker. There is a danger of receiving an injury.
7. Turn off the power supply beforehand when setting the waste bin. There is a danger of receiving an injury.
8. Turn off the power supply beforehand when removing paper scraps. There is a danger of receiving an injury.
9. Avoid the combined use of the creaser and the perforator, as it may cause a paper jam or a mechanical failure.
10. For the perforator, papers of weight 65 lbs (Cover stock) [176 g/㎡] or less is to be used. Using heavier paper may cause a paper jam or mechanical failure.
11. Do not exceed the MAX level when stacking the paper. Exceeding it may cause a mechanical failure.
12. Turn off the power supply beforehand when starting maintenance or inspection. There is a danger of receiving an injury.
13. When you install a machine, please install to a place with no dust, and the place which is not influenced with a liquid. It becomes the cause of failure if the installation method is mistaken.
14. When you put a machine into operation, please change into the state where all covers were closed. If it works where a cover is opened, there is fear of an injury.

Read this "Operation Manual" carefully before use. In particular, be sure to read "Safety Instructions" (page 2 to page 3) to ensure that the machine will be used properly.

Keep the manual at an appointed place with care so that it may be accessible whenever necessary.

The specifications of this product are subject to change for improvement. Therefore, don't mistake the "Operation Manual" of one product of the same model for that of another because descriptions in the "Operation Manual" of products of the same model may differ.

Contents

1. Before use........................................................................................................................................ ６

(1) Description and quantities of accessories ................................................................................... ６

(2) Exterior features .......................................................................................................................... ７

(3) Installation ................................................................................................................................... ９

2. Operating instructions ...................................................................................................................１１

(1) Checks before use ...................................................................................................................１１

(2) Setting of stacker......................................................................................................................１１

(3) Waste box setting .....................................................................................................................１２

(4) How to attach the business card stacker. .................................................................................１２

(5) Paper setting ............................................................................................................................１３

(6) Paper slant adjustment.............................................................................................................１４

(7) Crease depth adjustment .........................................................................................................１４

(8) How to attach the perforator .....................................................................................................１５

(9) How to adjust the perforation location ......................................................................................１６

(10)How to adjust the depth of perforation.....................................................................................１７

(2) Slitter initial location movement ................................................................................................１８

(4) Free entry .................................................................................................................................２１

(5) User program retrieval..............................................................................................................２１

(6) User program registration.........................................................................................................２２

(7) Setting of slitter and feed table .................................................................................................２３

(8) Operation number cancellation.................................................................................................２３

(10) Speed change ........................................................................................................................２５

(11) Cut mark on/off selection ........................................................................................................２６

4. Instructions for use ........................................................................................................................２７

(1) If the machine stops during operation ......................................................................................２７

(2) If Paper scrap remains on the machine....................................................................................２８

(3) Details concerning errors..........................................................................................................２９

(4) If the cut measurement does not match the input value ...........................................................３４

5. Product specifications ...................................................................................................................３５

6. Equipment, Electric circuit and parts .............................................................................................３７

7. Ordering consumables, etc. ..........................................................................................................４０

1. Before use

(1) Description and quantities of accessories

(2) Exterior features

1. Name of parts

3. Crease Depth Adjustment Dial

8. Slant Adjustment Dial

2. Electric-power-related points The electric power switch and the inlet are located inside the machine, below the feed table.

① When it is set at “I”, the power is turned on. ② When it is set at “O”, the power is turned off.

Plug in the electric power cord here.

Electric Power Plug this to the inlet. Cord

1. The machine installation method

Please be sure to LOCK a caster brake after making it move to the target position, when

Caution

When you install a machine, please install to a place with no dust, and the place which is not influenced with a liquid. It becomes the cause of failure if the installation method is mistaken.

2. Setting of feed table

Insert the feed table to the paper feeder, and set the feed table’s slotted holes onto the

protruding bolts on the machine. Install the 2 screws as shown below.

3. How to remove accessories

① Remove the chute screws.

② Lift the chute and take out the waste box.

③ The accessory case is inside the waste box.

Caution

Power it off. Otherwise, Injury could occur.

2. Operating instructions

(1) Checks before use

Check the following before operation.

① Is the electric power turned off?

② Is the feed table set?

③ Is the stacker set？

④ Is the electric power cord plugged in?

⑤ Is the waste box set?

2. Setting of stacker

① Open the stacker and set the stays in the indentation of the back of the stacker at an

appropriate angle to allow smooth paper ejection.

② Adjust the large paper guide according to the paper size.

Caution

Power it off. Otherwise, Injury could occur.

3. Waste box setting

① Set the waste box under the stacker.

Caution

Power it off. Otherwise, Injury could occur.

4. How to attach the business card stacker.

① Hang the business card stacker on Paper ejection port of Stacker panel.

② Find the V- notch to see where to put the business card stacker.

5. Paper setting

Press SET to lower the feed table.

Separate the sheets of paper well and place them on the feed table.

Fix the paper with the small paper guides.

Make sure that the paper stack does not exceed the MAX label.

Caution

Ensure that the paper stack does not exceed the MAX label, as it may cause a mechanical failure. Separate the sheets of paper well, as it may cause a paper jam.

6. Paper slant adjustment

When the printing is tilted, turn the dial as shown in the drawing below to make it straight.

Turning the dial counter-clockwise will tilt the paper to the right, whereas turning it

clockwise will tilt the paper to the left.

7. Crease depth adjustment

The sign shown in the drawing below will be displayed when using the creaser.

Turn the dial shown in the drawing below to adjust the crease depth.

The depth will become the most shallow by choosing Level 1 and the deepest by

When selecting Levels 4 and 5, be careful of the paper thickness. Placing the crease too

deep may cause a paper jam or a mechanical failure when the paper is thick.

Caution

Avoid the combined use of the creaser and the perforator, as it may cause a paper jam or a machine failure.

When selecting Levels 4 and 5, be careful of the paper thickness. Placing the paper too deep may cause a paper jam or a machine failure when the paper is thick.

8. How to attach the perforator

① Power it off.

② The perforator is stowed below the feed table.

③ Detach the gear cover located at the paper exit and attach the perforator.

④ The gear cover can be attached where the perforator was initially placed.

⑤ The target paper weight for the perforator is 65 lbs (Cover stock) [176 g/㎡]or less.

⑥ The combined use of the perforator and the creaser on the same paper may cause a paper

jam or a mechanical failure.

Caution ： Be sure to install Gear cover or Perforator unit !

For safety reason, machine doesn't work with cover open, or if these parts are not in

Caution

Power it off. Otherwise, Injury could occur. The maximum paper weight for use is 65 lbs (Cover stock) [176 g/㎡] for the perforator. Using a heavier paper may cause a paper jam or a mechanical failure. Combined use of the perforator and creaser may cause a paper jam or a mechanical failure Attach the gear cover when the perforator is not in use, as it may cause injury.

9. How to adjust the perforation location

① When using the perforator, the screen will display where to fix the perforator, as shown

② Set the lower blade to the right end of your desired scale and fix it.

③ Set the upper blade lightly against the lower blade and fix it.

④ Adjust the rest of the aid rollers according to the paper size so that the paper feeding will go

Caution

Avoid the combined use of the creaser and the perforator, as it may cause a paper jam or a mechanical failure. Avoid contacting the cutting edge of the perforating blade. Otherwise, injury could occur.

(10)How to adjust the depth of perforation

① Change in the paper thickness, recommend you adjust the depth of Perforation.

② Loosen both lock levers, move adjustment levers;

③ Lock position by tightening lock lever.

Caution

Avoid contacting the cutting edge of the perforating blade. Otherwise, injury could occur.

3. Operational method

① Turning the power on.

② Slitter initial location movement (When turning the power on initially and after adjusting

③ Format selection/free entry, user program retrieval, etc.

④ Slitter and table setting

⑤ Creaser adjustment (when using the creaser)

⑥ Perforator adjustment (when using the perforator)

⑨ Input value correction and size correction

⑩ Start of operation

2. Slitter initial location movement (When initially turning the power on and after adjusting the head location)

① Turn the power on.

② Press INITIAL POSITION from the operation screen.

③ The slitter will move to the initial position.

④ The INITIAL POSITION sign will change to SET upon completion.

3. Format selection

② Select the paper type to be used.

Return to Operation Screen

③ Select the cutting pattern.

Move to Cutting Pattern Confirmation Screen

Confirm cutting pattern and move to Operation Screen

Return to Paper Selection Screen

④ Cutting pattern content confirmation and partial correction

Press A through N to make corrections. O,P and M are automatic calculations. It is

possible to enter in inches up to the 3rd decimal place.

Number of pieces in the depth direction

Number of pieces in the feeding direction

Confirm cutting pattern and move to Operation Screen

Return to Cutting Pattern Selection Screen

Please use as a calculator

Cancel input value and return

Confirm input value and return

Touch it when you do not want to make any crease. I,J,K,L will be 0.000”.

Return to Cutting Pattern Confirmation Screen

Creasing can be performed up to four

times per piece. It is not to be used in

combination with the perforator.

perforator is 65 lbs (Cover stock) [176 g/㎡].

It is not to be used in combination with the

4. Free entry

② The operation is almost the same as (3)-④.

Move to User Program Retrieval Screen

Move to User Program Save Screen

Confirm cutting pattern and move to Operation Screen

It turns automatically into CREASE ON when you input the measure of any crease pos.

Line is the number of crease you make on a sheet.

Return to Operation Screen

5. User program retrieval

① 50 user program can be registered.

② Press the button of the name you wish to retrieve.

Move to the previous 10 program

Move to the next 10 program

Return to Cutting Pattern Correction Screen

③ Confirm the details of the program for retrieval.

Move to the previous program Enter the number to jump to it

Move to the next program

Retrieve user program and go to Operation Screen

Return to User Program Selection Screen

6. User program registration

① 50 user program can be registered.

② Press the button in which you wish to make a registration.

Move to the previous 10 program

Move to the next 10 program

Return to Cutting Pattern Correction Screen

③ Confirm the program stored in the selected place.

Currently registered name Double Click to make a copy of input name. Move to the previous program

Enter the name for registration

Enter the number to jump to it Move to the next program

Return to User Program Selection Screen

Uppercase/lowercase switching

Cancel the entry and return

Finalize the registration name

Change to number entry

For overwriting and move to Cutting Pattern Correction Screen

Return to User Program Detail Screen

Press here to select the following symbols which will be displayed one by one: ､｡･!?:;^"'~|｢｣[]{}<>$%&¥#+-*/=()

Delete and move to User Program Detail Screen

Return to User Program Detail Screen

7. Setting of slitter and feed table

① By pressing SET, the feed table will be lowered to the bottom dead point and the slitter will

move to the operating position.

② The display will change from SET to START upon completion.

8. Operation number cancellation

① The total number of processed sheets are counted. Press CLR and hold to clear the

number. You can change the Total number.

Total number of operated sheets

You can make a little adjustment on Total number.

9. Manual operation

②Use it when operating manually.

The feeder will rotate.

The feeder will rotate in reverse

Feeder speed Fast/Slow switching

The guillotine will operate once.

The creaser will operate once.

Return to Operation Screen

Move to Adjust Screen

☞ 4-(4) If the cut measurement does not match the input value

10. Speed change

① Press SPEED from the Operation Screen.

② There are eight feeding speed levels. The currently selected speed level is inverted to

black. Thick paper should not be fed at higher speeds.

Please slow the speed down if

sheet stops with noise associated.

③ To avoid double feed or skew feed, adjust PAPER FEED WORK TIME and volume of AIR

BLOW.

PAPER FEED

WORK TIME

SHORT

Double feed: more likely to occur Skew feed: less likely to occur

LONG Double feed: less likely to occur Skew Feed: more likely to occur

BLOW OFF

SHORT BLOW LONG BLOW Double feed: Double feed: more likely to occur less likely to occur AIR BLOW Skew feed: Skew feed: less likely to occur more likely to occur As a recommended default setting, PAPER FEED WORK TIME should be 3.0 seconds

and AIR BLOW should be LONG BLOW.

Return to Operation Screen

The value is for easy double feed detection. The operation will become an error and stop if a longer sheet of paper than the input value of the first sheet is fed. Enter 0 when you do not use the function.

11. Cut mark on/off selection

Select C/MARK ON to use cut marks. Select C/MARK OFF for not using cut marks.

12. Automatic operation

① Set the number of sheets for operation. The machine will automatically stop on reaching

the set number. Enter “0” for continuous operations.

User program Job Number you have retrieved is displayed.

Enter the number of sheets for operation. (Batch Counter) Enter “0” for continuous operations.

② Press START to start an automatic operation. The display will change to RUNNING.

③ Press STOP and the machine will make an EMERGENCY stop even if the operation is

④ Press END if you wish to stop the machine when the current sheet is completed. The END

sign will blink and the machine will automatically stop upon completion of the work.

Number of sheets completed

4. Instructions for use

(1) If the machine stops during operation

① If the machine stops during operation due to an error such as a paper jam and

overloading, paper may still be left in the machine.

② In such a case, the paper must be removed by manual operation, as continuing to operate

it may cause a mechanical failure

③ Press MANUAL from the Operation Screen, and then press ＜ or ＞ from the screen, or

press ＜ or ＞ from the error screens as shown above to move the feeder for paper

Caution

Avoid contacting any rotating object. Otherwise, injury could occur. Don't bring a hand, face, hair, sleeves of clothes and the like close to the rotating parts of the machine. There is a danger of receiving an injury.

2. If Paper scrap remains on the machine

① If paper scrap remains behind Stacker panel.

If paper scraps remain in the Crease part of machinery, turn off the machine and open the

stacker panel by removing thumb screw on both sides of the Stacker Panel.

scraps with Tweezers and take them away.

② If the paper scrap remains under cutter cover.

If Paper scrap remains under the Cutter cover of the machine, turn off the machine and take

off thumb screw to remove the anti-static brush setting plate. After removing plate there will

Push the paper scrap down with Waste ejector, which comes with machine.

Thumb screws Anti-static Brush Setting Plate

Caution

Power it off. Otherwise, Injury could occur.

3. Details concerning errors

① Paper size error

Correct the paper size to fit in the value range below.

② Final cutting measurement error

Correct the final cutting measurement to exceed the value specified below.

③ Cutting measurement error

Correct the cutting measurement to fit in the value range below. The maximum value is

subject to change depending on the entered paper size.

④ Cut piece number error

Correct the number of cut pieces to be in the value range below. The maximum number of

pieces is subject to change depending on the operation.

⑤ Bottom margin error

Correct the bottom margin to fit in the value range below.

⑥ Top margin error

Correct the top margin to fit in the value range below.

⑦ Back margin error

Correct the back margin to fit in the value specified below.

⑧ Perforation location error

Correct the paper size to fit in the value range below.

⑨ Crease front margin error

Correct the crease front margin to exceed the value specified below.

⑩ Crease back margin error

Correct the crease back margin to exceed the value specified below.

⑪ Perforation location warning

Correct the perforation location to fit in the value range below. The maximum value is

subject to change depending on the entered paper size.

⑫ Leading edge margin and cut mark margin warning

Correct the measurement so that the leading margin becomes larger than the cut mark

⑬ Cover open error

Safety cover or Stacker panel might be open, Gear cover or Perforator might not be

Make sure to close the Safety cover and Stacker Panel is closed and Gear cover or

Perforator is mounted correctly.

⑭ Paper jam error

Paper remains inside the machine. Remove the paper.

⑮ Timeout error 1

Paper was not fed within a set time period. Check the paper feeder.

⑯ Timeout error 2

Paper did not pass through within a set time period. Remove the paper remaining inside

⑰ Overload error 1

Cutting or creasing did not complete within a set time period. Remove the paper

remaining inside the machine.

⑱ Overload error 2

An overloading error occurred at the feed table. Check the feed table.

⑲ Overload error 3

An overloading error occurred at the slitter. Check the blinking slitter.

⑳ Cut mark detection error

Cut mark was unable to be detected. Check the cut mark. Eject the paper inside the

Paper length variation or double feed detection error

Paper lengths vary. Check the paper.

Slitter units positioning error

Slitter position is out of valid range. Check paper size and input data.

Communication with the touch panel is not possible. Turn off the power, and turn it on

again after 5 seconds or longer.

4. If the cut measurement does not match the input value

① If Measurement A is different: When the input value is 0.200” and the actual cut

measurement is 0.175”, input +0.025”; input -0.040” when the actual cut measurement is

② If Measurements B, C, or D are different: When the input value is 3.500” and the actual

cut measurement is 3.560”, input -0.060”; input +0.080” when the actual cut measurement

③ If Measurement E is different: When the input value is 0.600” and the actual cut

measurement is 0.620”, input -0.020”; input +0.050” when the actual cut measurement is

0.550”. （You can input ±0.400” at the most）

④ If Measurement F (crease location) is different: When the input value is 2.000” and the

actual crease measurement is 2.250”, input -0.250”; input +0.100” when the actual crease

measurement is 1.900”. （You can input ±0.400” at the most）

⑤ If Measurement G is different: When the input value is 0.400” and the actual cut

measurement is 0.450”, input –0.050”; input +0.100” when the actual cut measurement is

0.300”. （You can input ±0.400” at the most）

⑥ Use H and I for magnificent adjustment.

If the printed image is bigger or smaller than the

one you designate, you can adjust cutting length to fit the printed measurement with this

magnificent adjustment.： When the input value is 4.000” and the actual cut measurement is

4.080”, input 0.980 (4.000” ÷ 4.080”); input 1.010 (4.000” ÷ 3.960”) when the actual

cut measurement is 3.960”. When this measurement is corrected, Measurements E, F

and G will need to be corrected as well. Refer to ③–⑤above and make corrections. （H

must be from 0.500 times to 2.000 times and I must be from0.800 times to 1.200times）

※：If you press OK after you input values into A, B, C and D, those values will be added to

each total measurements which are circled on the image below. Then, A, B, C and D will

be reset to 0.000. You can change the measurement by 0.002”. Each adjustment should

be within±0.080” at one time.

If the gap is more than±0.080”, repeat the process until

the desired measurement is reached.

Total measurement that has been changed A, B, C, and D.

Correct the measurement and Return to Manual Operation Screen

Return to Manual Operation Screen without making corrections

5. Product specifications

4 sets (6 slitter blades)

1 set (5-level manual crease depth adjustment)

Number of guillotine or creasing

Paper size (depth direction)

8.25” (A4 short) ～14.375” (B3 short)

Paper size (feed direction)

8.25”(A4 short) ～20.500” (B3 long)

MIN1.97”W×2.165”D

32 lbs (Bond) – 130 lbs (Cover stock) [120-350g/㎡]

Maximum paper curl size

Offset, Coat, UVcoat, Glossy, Laminate

MAX2.35”

MAX 10 sheets per minute (in case of one cut from A4 to A5) 34.5” W ×28.1” D× 40.8” H (Occupancy area: 67.7” W×28.1” D×59.1” H )

Single phase 100-240VAC, 50/60Hz, 2.0A-0.8A

23 to 104°F (-5 to 40°C)

• 13 to 149°F (-25 to 60°C)

Category Ⅲ according to IEC60664-1

Degree 3 according to IEC60664-1

④Cut mark size and position

⑤Crease limitations （Max. four times）

7. Ordering consumables, etc.

When ordering consumables or parts, be sure to specify the machine model.

OPERATION MANUAL

Keep this “Operation Manual” at an appointed place with care so that it

may be available whenever required.

If this “Operation Manual” is stained or lost, make contact with the

distributor or our salesman or customer service section to ask for a new

operation manual after making sure of its contents.

UCHIDA YOKO CO., LTD.