MBM BookletMaker Jr. Manual, page 1

Page 1 of 11

MBM BookletMaker Jr. Manual, page 2
Text on page 2

Operation Manual

FOR

BOOKLETMAKER Jr.

Keep this manual sot that it can be retrieved whenever needed

Page 2 of 11

MBM BookletMaker Jr. Manual, page 3
Text on page 3

CAUTION

When the machine is running, never put your hands near or under the rollers.

Do not remove the bottom lid, front and rear covers from the machine. The inside of the machine contains high voltage parts or hazardous moving parts, which may cause electric shock or personal injury.

A socket-outlet shall be installed near the equipment and shall be easily accessible.

Page 3 of 11

MBM BookletMaker Jr. Manual, page 4
Text on page 4

Warning

Warning: hazardous moving parts keep hands and other body parts away.

Warn: The surface of the , motor is hot. Be careful, Don t touch

Caution

Caution: For continued protection against risk of fire, replace only with the same type and rating of fuse.

Page 4 of 11

MBM BookletMaker Jr. Manual, page 5
Text on page 5

No.

Description

Qty

Warning Label 1

Cover Label

Brand Label

Model Label

Fuse Label

Caution Label

Warning Label 2

Warning Label 3

Page 5 of 11

MBM BookletMaker Jr. Manual, page 6
Text on page 6

(2) Back Cover

(3) Stapling Handle

(4) Side Guide (B)

(5) Sub Holding Shaft

(9) Table

(10) Side Guide (A)

(11) Front Cover

(12) On/Off Switch

(13) Rubber Feet

Page 6 of 11

MBM BookletMaker Jr. Manual, page 7
Text on page 7

Wa rning ha za rd o us m o ving p a rts ke e p ha nd s a nd o the rbodypa rts a wa y

Do not remove the cover Doing so may result in personal injury

M O D EL

BO O K LETM A K ER Jr.

N . Ch arle st o n , SC 2 9 4 1 8

Page 7 of 11

MBM BookletMaker Jr. Manual, page 8
Text on page 8

CA UTION:

Warn: The surface of the , motor is hot. Be careful, Don t touch

Warn: The surface of the , motor is hot. Be careful, Don t touch

Page 8 of 11

MBM BookletMaker Jr. Manual, page 9
Text on page 9

Operation Procedures

  1. B ef o r e Op er at i n g

1.1 Fit stapling handle:

First insert the end of the stapling handle at the main holding shaft then press in the sub-holding shaft.

1.3 Connect the power cable

2.1 Switch on the machine

2.2 Choose the correct staple position according to the sheet size.

2.3 Set the paper guides; place the sheets under the rollers and align the sheets to side guide (A).

2.4 Set the paper guides to hold the sheets in position.

2.5 Press down the stapling handle to complete the stapling.

2.6 Lift up the stapling handle and firmly press down to the other side and hold. The stapled sheets will be fed up through the fold rollers to complete the booklet.

2.7 Repeat steps 2.3-2.6 for further booklets.

2.8 Switch off the machines after finishing.

Page 9 of 11

MBM BookletMaker Jr. Manual, page 10
Text on page 10
  1. Si d e St ap ling

3.1 Choose and fix the staple position according to the sheet size.

3.2 Place the sheets under the rollers.

3.3 Depending on the stapling position, align the sheets to side guide (A)or side guide (B)

3.4 Set the side distance and hold the sheets.

3.5 Press down the stapling handle for stapling.

3.6 Repeat steps 3.2-3.5 for further side stapling.

  1. Rep ai r & Mai n t en an c e

4.1 Always clean up machine after used.

Page 10 of 11

MBM BookletMaker Jr. Manual, page 11
Text on page 11

Sp ec ific at ions

Min.197mmx273mm (7.8 x 10.8 ) Max. 297mmx420mm ( 11.7 x 16.5 )

Max. Stapling Amount 10 sheets of 70gsm Bond paper*

( 20 lbs. paper)

10 sheets of 70gsm Bond paper * [40 pages booklet] (20 lbs. paper)

AC 110V 0.8A 60Hz

500mmx235mmx395mm (19.7 x 9.3 x 15.6 )

15Kg ( 33lbs.)

  • This may vary depending upon paper quality

Page 11 of 11 ยท End of manual

Quick start

  1. Fit the handle: Insert the end of the stapling handle at the main holding shaft, then press in the sub-holding shaft.
  2. Power: Connect the power cable and switch on the machine.
  3. Set staple position: Choose the correct staple position for the sheet size.
  4. Set the guides: Place the sheets under the rollers and align them to side guide (A). Set the paper guides to hold the sheets.
  5. Staple: Press down the stapling handle to staple.
  6. Fold: Lift the handle, then firmly press it down to the other side and hold. The sheets feed through the fold rollers to make the booklet.
  7. Finish: Repeat for more booklets. Switch off the machine when done.

Troubleshooting

ProblemLikely causeFix (from the manual)
Risk of injury at the rollersHands were near or under the rollers while running.Never put your hands near or under the rollers when the machine is running. Page 3
Risk of shock or injury inside the machineCovers were removed.Do not remove the bottom lid, front cover, or rear cover. The inside has high voltage and moving parts. Page 3
Motor surface is hotThe motor gets hot in use.Do not touch the motor surface. Page 4
Fuse needs replacingFuse has failed.Replace it only with the same type and rating of fuse. Page 4
Stapling fails on a large stackThe stack is over the stapling limit.Staple no more than 10 sheets of 70gsm (20 lb) bond paper. This may vary with paper quality. Page 11
Machine is dirty after useNo cleaning after use.Always clean up the machine after use. Page 10

Frequently asked questions

How many sheets can the BookletMaker Jr. staple?

Up to 10 sheets of 70gsm (20 lb) bond paper, which makes a 40 page booklet. This may vary with paper quality. See page 11.

What paper sizes does it take?

The minimum is 197 mm x 273 mm (7.8 x 10.8 in) and the maximum is 297 mm x 420 mm (11.7 x 16.5 in). See page 11.

Can it do side stapling?

Yes. Choose the staple position, place the sheets under the rollers, align them to side guide (A) or (B), then press down the stapling handle. See page 10.

What power does it need?

AC 110V, 0.8A, 60Hz. See page 11.

How much does it weigh?

It weighs 15 kg (33 lbs). See page 11.