

Page 1 of 9

Page 2 of 9

Text on page 3
CONTENTS:
Prohibited activities ................................................................................................................ 3
Main machine parts ................................................................................................................ 4
OPERATING INSTRUCTIONS .............................................................................................. 4
Preparing the machine for operation after unwrapping ................................................... 4
Machine operation .......................................................................................................... 5
Turning the perpendicular guiding of stops ............................................................. 5
Perforation and creasing tool replacement .............................................................. 6
Lower creasing bar positions ................................................................................... 7
Machine maintenance ............................................................................................................ 8
Machine and transport packaging disposal ............................................................................ 8
CREASING PRESSURE AND ADJUSTMENT ...................................................................... 8
Cover dismounting .......................................................................................................... 8
Adjusting the pressure of the upper creasing bar ........................................................... 8
2 Creasing and perforating machine GoCrease
Page 3 of 9

Text on page 4
1 Identification
Type marking: Manufacturer:
GoCrease TM 3000 MBM Corporation www.mbmcorp.com
2 Specification
The machine is designed for the treatment of common office paper or of paper with similar physicalchemical properties. The size of sheets is up to 12.6” x 17.7”, the maximum table width is 12.6” and the maximum basis weight of the processed paper is up to 400g/m 2 .
3 Parameters
- Max. machine working width
- Front table Max. distance of stop from creasing/perf. tool Min. distance of stop from creasing/perf. tool
- Back table Max. distance of stop from creasing/perf. tool Min. distance of stop from creasing/perf. tool
- Crease width
- Built-up area
6.3” 1.1” 0.03” / 0.04” / 0.05” l = 18.5” w = 14.6” h = 14.2” (The lever at the top dead center)
- Transportation size l = 18.5” w = 14.6” h = 6.3” (The lever at the bottom dead center)
- Basis weight 80 – 400 g/m² (creasing) 80 – 250 g/m² (perforating) i) Machine weight 24 lbs.
Note: The use of the machine requires that the extension size (see point f) be extended by a working area necessary for handling the machine.
4 Prohibited activities
The machine is designed only for the creasing of paper with the above set parameters. The machine can be operated only in protected, enclosed and covered areas (offices, workshops). It is prohibited to operate the machine if its operation is not continuous; e.g. when it gets jammed or is damaged. During operation the machine must be covered, complete and in perfect condition.
Page 4 of 9

Text on page 5
5 Main machine parts
Machine base Stop guide way Stop Lever Upper bar Lower bar Cover
6 OPERATING INSTRUCTIONS
6.1 Preparing the machine for operation after unwrapping
Remove both the machine and the lever from its packaging. Stabilize the machine on a firm, even surface. Screw the lever into the opening (10) with a cam shaft thread in the cover hole.
Page 5 of 9

Text on page 6
6.2 Machine operation
The creaser has two sliding stops (3) with tilting stop discs that are adjusted to a required crease and perforation position according to a millimeter scale. The set position of the stops (3) is secured with arresting bolts (9). When the minimum or maximum distance of the crease from the paper edge is required the stops (3) can be exchanged. The lower creasing bar (6) is finished with longitudinal grooves - 0.03” / 0.04” / 0.05” wide – on either side. Depending on the weight of the processed paper the crease width is selected according to Article 6.2.3.
6.2.1 Turning the perpendicular guiding of stops
Loosen the screws (13) by approx. half turn and using the rotating handrail (12) select a required guiding angle. Then tighten the screws (13).
Note: The correct initial position of the guiding line and a 90° angle are set when the crease axis (b) of the guiding line is identical (collinear) with an opening in the table (a).
Page 6 of 9

Text on page 7
6.2.2 Perforation and creasing tool replacement
Unscrew the lever (15), loosen the screws (16) and disengage the cover (7). Loosen the screws (17), disengage the T-square (18) and the perforating tool (19). Replace it with the creasing tool
- held in the magnetic holder in the rear part of the cover.
When inserting a new tool proceed in the opposite sequence; before the final tightening of the screws (17) force the lever (15) gently to push the tool on the contact surface of the lower bar in position D. Then tighten the screws.
Page 7 of 9

Text on page 8
6.2.3 Lower creasing bar positions
- 0.03” crease position
- 0.04” crease position
- 0.06” crease position
- Perforation position
80-120g/mm 2 120-200g/mm 2 200-400g/mm 2 80-250g/mm 2
Page 8 of 9

Text on page 9
7 Machine maintenance
Once in 6 months check the friction points of the upper bar and side guide ways and lubricate them if necessary.
8 Machine and transport packaging disposal
Pursuant to the Decree of the Ministry of the Environment No. 381/2001 Sb. as annotated through Decree No. 503/2004 Sb., and pursuant to the Decree of the Ministry of the Environment and of the Ministry of Health No. 376/2001 Sb. on the evaluation of the dangerous properties of waste and pursuant to Act No. 185/2001 Sb on waste. When the machine completes its service life it can be liquidated together with communal waste. It has to be dismounted and its parts are sorted to metal and non-metal parts, plastics or rubber components. These components are then taken to appropriate collecting yards for recycling. Machine parts are not made from dangerous materials and therefore are handled as communal waste that does not require special treatment of a professional company.
9 CREASING PRESSURE ADJUSTMENT
9.1 Cover dismounting
Unscrew the lever (15), loosen both screws on the cover (16) and stick the cover out (7) in the upward direction.
9.2 Adjusting the pressure of the upper creasing bar
Complete this adjustment by means of 3 arrestment bolts. Loosen the nuts (21) and the screw (22). Stabilize all arrestment bolts in such a position so that the perforating knife evenly touches the lower bar (6) (position D) along the entire contact surface once the machine has been pressed, Maximum press power shouldn’t exceed 100 N (22 lbs.). After completing the required settings tighten the nuts (21). This procedure is applicable for both, creasing and perforating.
Page 9 of 9 ยท End of manual
Quick start
- Unpack: Remove the machine and the lever from the packaging.
- Place it: Stabilize the machine on a firm, even surface.
- Fit the lever: Screw the lever into the opening with the cam shaft thread in the cover hole.
- Set the stops: Adjust the two sliding stops to the crease or perforation position using the millimeter scale. Secure each position with its arresting bolt.
- Choose the crease width: Select the lower creasing bar position by paper weight. Position 0.03 is for 80 to 120 g/m2, 0.04 for 120 to 200 g/m2, 0.06 for 200 to 400 g/m2. The perforation position is for 80 to 250 g/m2.
- Use within limits: Use office paper up to 12.6 x 17.7 inches, in an enclosed, covered area. Stop and do not run the machine if it jams or is damaged.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Machine jams or is damaged | The machine must run continuously and be in perfect condition. | Do not operate the machine when it jams or is damaged. During operation it must be covered and complete. Page 4 |
| Crease does not suit the paper weight | The lower creasing bar is in the wrong position for the paper. | Select the creasing bar position by paper weight, as listed in Article 6.2.3. Page 8 |
| Creasing or perforating is uneven | Pressure of the upper creasing bar needs adjusting. | Remove the cover. Loosen the nuts (21) and the screw (22). Set the 3 arrestment bolts so the perforating knife touches the lower bar evenly along the whole surface. Maximum press power should not exceed 100 N (22 lbs). Tighten the nuts. Page 9 |
| Stops do not guide paper at a right angle | The guiding angle of the stops is off. | Loosen the screws (13) about half a turn, set the angle with the rotating handrail (12), then tighten. The correct 90 degree position is when the crease axis lines up with the opening in the table. Page 6 |
| Perforating or creasing tool needs replacing | The tool must be swapped for the job. | Unscrew the lever, loosen the screws (16) and remove the cover. Loosen the screws (17), remove the T-square and the tool. Fit the new tool in the opposite order, then tighten the screws. Page 7 |
| Moving parts feel stiff | Friction points need lubrication. | Every 6 months, check the friction points of the upper bar and side guide ways, and lubricate them if needed. Page 9 |
Frequently asked questions
What paper size can the GoCrease 3000 handle?
Sheets up to 12.6 x 17.7 inches. The maximum table width is 12.6 inches. See page 4.
What paper weight can it crease and perforate?
Creasing is 80 to 400 g/m2. Perforating is 80 to 250 g/m2. See page 4.
Where can I use it?
Only in protected, enclosed and covered areas such as offices and workshops. See page 4.
How do I set the crease position?
Adjust the two sliding stops using the millimeter scale. Secure the position with the arresting bolts. See page 6.
How often does it need maintenance?
Once every 6 months, check the friction points of the upper bar and side guide ways and lubricate them if necessary. See page 9.
