

Page 1 of 5

Page 2 of 5

Text on page 3
CONTENTS:
1) Warning
2) Parameters
3) Machine description
4) Installation and adjustment
5) Troubleshooting
6) Cover removal
7) Disposal
1) Warning
a) Creasing and perforating machine is suited for creasing and perforating paper of set parameters only.
b) It is not allowed to groove or perforate other material than paper.
c) Do not use this machine when the electrical cord has been damaged.
d) Do not plug the machine into other voltage, than the one appointed on a manufacturer’s label.
e) All the instructions should be read before you start using the machine.
f) To decrease risk, it is necessary to check that the machine is not being used within the reach of children.
g) Do not put fingers in the machine after it has been plugged in.
h) After the stoppage, the machine has to be unplugged first, and then the clearing process can start. i) Do not replace a faulty safety fuse with a different type of fuse, or a fuse with different electric output. The machine has to be unplugged when changing safety fuse.
2) Parameters
a) paper size
d) total weight
e) voltage
5.8” x 8.3”, 8.3” x 11.7”, 11.7” x 16.5”, max. width 17.7” operating position: length = 28” width = 21.25” height = 11.4” shipping dimensions: length = 25.6” width = 25.2” height = 15.7” perforation: 80 – 250 g / m² creasing: 80 – 400g/ m² : 84 lbs. 120 V / 60Hz
- Machine description Electrical creasing and perforating machine is suited for final processing of graphical material up to 17.7” width. Creasing enables easy folding of paper. Perforating can be done simply by a blade change, and turning the square (7) head without further adjustment. Wasteless perforation allows easy paper separation. Millimeter scales, which are used to adjust paper stops, are placed on the sides of the table. The machine is controlled, either by a handoperated switch on the cover, or by a foot pedal. (2)
Page 3 of 5

Text on page 4
- Installation and adjustment When the machine is unpacked, it is placed on a solid flat surface. First the back table has to be fixed, and also the food pedal if needed. (2) Then, after the machine has been plugged in, it is set in a working order and the control diode beams constantly (5).
Standard creasing has been preset by manufacturer.
For perforating, it is necessary to replace the creasing tool with a perforating tool, which is enclosed. Further, the square bar has to be adjusted - smooth surface up (7). First the machine has to be unplugged, then remove the back table (4). Open the cover (1). There are five screws and (6) clips (8) which have to be dismounted. Screws should not be tightened completely after insertion of perforating tool until
Page 4 of 5

Text on page 5
the check test is carried out, which secures that the square bar is parallel to the perforating tool. Then all the screws are tightened completely.
In case of poor quality of perforating, or when having trouble with separation of the paper after perforating is completed, it is necessary to adjust the upper bar. (10)
The upper bar (10) with perforating (creasing) tool can be moved down by the help of both adjusting screws. The screws should be loosened in gradually by 1/6 th revolution to the left approx. 60˚. (the bar moves down) and then it has to be fastened by a nut. After each 60˚ turn it is necessary to check, whether perforating (creasing) quality is sufficient. When the upper is set-up correctly (10) it is not needed to readjust it with each change of function (perforating, creasing).
- the diode flickers approx. 1x /sec : options - the upper cover (1) is open, the back table (4) is pushed out
- the diode flickers approx. 2x /sec : the upper bar travel mechanism has been blocked, it is necessary to unplug the machine and then turn the adjusting studs (9) to the right (approx. 2 turns) and then the upper bar moves up. After the machine is turned back on, the unfinished travel cycle will finish automatically. It is necessary to readjust the upper bar. (10)
- defective fuse replacement: from service manual
Cover removal (disassembly) can be conducted by a specialized person only, and only after the machine has been switched off and unplugged.
At the end of its operating life, it is not allowed to place this machine among general mixed municipal waste. It should be taken into metal, non-metal, plastic, rubber and electric parts. These will be committed to appropriate collection places for further processing. Some part of the machine may contain dangerous substances, which may be health and environment dangerous.
Page 5 of 5 ยท End of manual
Quick start
- Read first: Read all instructions before you use the machine. Use it only for paper that fits the listed parameters.
- Place the machine: After unpacking, put it on a solid flat surface.
- Fit the parts: Fix the back table. Attach the foot pedal if you want to use it.
- Plug in: Plug the machine in only to the voltage on the manufacturer label. The control diode shines steadily when the machine is ready.
- Crease: Standard creasing is preset by the manufacturer. Control the machine with the hand switch on the cover or with the foot pedal.
- Switch to perforating: Unplug the machine and remove the back table. Open the cover and swap in the supplied perforating tool. Set the square bar smooth surface up.
- Adjust the upper bar: If perforating is poor or paper will not separate, lower the upper bar with both adjusting screws in small turns. Check quality after each turn.
Troubleshooting
| Problem | Likely cause | Fix (from the manual) |
|---|---|---|
| Diode flickers about once per second | The upper cover is open or the back table is pushed out. | Close the upper cover and set the back table in place. Page 5 |
| Diode flickers about twice per second | The upper bar travel mechanism is blocked. | Unplug the machine. Turn the adjusting studs to the right about 2 turns so the upper bar moves up. After you turn the machine back on, the unfinished cycle finishes on its own. Then readjust the upper bar. Page 5 |
| Poor perforating or paper will not separate after perforating | The upper bar needs adjusting. | Loosen both adjusting screws gradually, about 1/6 turn (approx. 60 degrees) at a time, to move the bar down. Fasten with the nut and check quality after each turn. Page 5 |
| Machine stops working or paper stoppage | Paper is stuck in the machine. | Unplug the machine first. Only then start clearing the stoppage. Do not put fingers in the machine when it is plugged in. Page 3 |
| Perforating tool installed but not working well | The square bar may not be parallel to the perforating tool. | Do not fully tighten the screws until the check test confirms the square bar is parallel to the tool. Then tighten all screws completely. Page 5 |
Frequently asked questions
What paper sizes does the GoCrease 4000 handle?
The manual lists 5.8 x 8.3, 8.3 x 11.7 and 11.7 x 16.5 inches, with a maximum width of 17.7 inches. See page 3.
What paper weights can it perforate and crease?
Perforation is rated for 80 to 250 g/m2. Creasing is rated for 80 to 400 g/m2. See page 3.
How do I switch from creasing to perforating?
Unplug the machine, remove the back table and open the cover. Replace the creasing tool with the supplied perforating tool and set the square bar smooth surface up. See page 4.
How do I run the machine?
Use the hand switch on the cover or a foot pedal. See page 3.
What power does it need?
The manual lists 120 V / 60 Hz. Do not plug it into other voltage than the one on the manufacturer label. See page 3.
