MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 1

Page 1 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 2
Text on page 2

TM

GoCrease

AutoAir

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 2 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 3
Text on page 3
  1. Introduction We are presenting you with Operating Instructions that contain machine technical data and instructions necessary for the correct setting, start-up, operation and maintenance of the machine.

The Operating Instructions are intended for machine operators as well as for service engineers. The individuals manipulating, installing and operating the machine should familiarise themselves with the instructions before they start. We would like to emphasise that service operations may only be executed by authorised individuals with proper qualification. They should be thoroughly familiar with the control and all functions of the machine. Any repair done without authorisation may render the warranty null and void. Reference is made to Section 2.2 – Work Safety and Health Protection providing basic information about safe use of the machine and operator's health protection. Please pay due attention to this section. Be aware that the final responsibility lies with the individuals working with the machine.

The machine construction complies with Directive 98/37/EC of the European Parliament and of the Council. If all the instructions in this document are respected, the machine will render satisfactory and precise performance.

We can assure you that the machine has received maximum care. Thoroughness of control ensures machine precision within the scope of the acceptance standards applicable to this machine. We believe these Operating Instructions will be a valuable guide for you.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 3 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 4
Text on page 4
  1. SAFETY RISKS

2.1 Warning

When using GoCrease AutoAir all safety rules and procedures as well as all warnings regarding work safety and health protection listed in this document must be observed. Otherwise, considering the bellow listed factors, a serious injury of a person, damage or destruction of the machine, its parts or accessories could occur.

Factors increasing risk:

  • Rotating pulleys and moving belts
  • Noise made during processing
  • Moving parts of the machine and equipment
  • Sharp edges created during processing
  • Dust created during processing

2.2 General Work Safety and Health Protection

This section provides the user with basic information about work safety and health protection of the operator and any other individuals who come into contact with the machine.

If the GoCrease AutoAir is used correctly, it is a very safe machine. However, if used incorrectly, it can be dangerous. When operating the machine, the operator is responsible for their own personal safety. The manufacturer may not be held liable for any personal injury or damage to the machine caused by use or operation at variance with these Operating Instructions. The owner of the machine is responsible for the machine being operated, maintained and serviced only by qualified personnel.

The machine design is in compliance with international standards and regulations for construction of machine tools. For the machines exported to the European Economic Area (EEA), the customer will obtain a "Declaration of Conformity" together with the accompanying technical documentation for the machine - Operating Instructions. Also, the machine bears the CE marking.

The CE marking on the machinery signifies that the product complies with the technical requirements specified in all the legal regulations that apply to the machinery and that require or allow this marking. This marking also signifies that a specified procedure was followed during the assessment of the stated conformity.

The manufacturer certifies by means of the “Declaration of Conformity” that the machinery concerned complies with the requirements of Directive 98/37/CE of the European Parliament and of the Council and those of the harmonised technical standards. Directive 98/37/CE of the European Parliament and of the Council is a document defining the generally applicable basic requirements for health protection and safety of machinery operated at the user’s facility within the EEA.

Page 4 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 5
Text on page 5

Directive 98/37/CE of the European Parliament and of the Council does not apply to the machinery exported to countries outside the EEA.

The customer will receive the accompanying technical documentation for the machine – Operating Instructions. The manufacturer hereby requests that the user trains its staff accordingly in order to ensure comprehensive safety as directed by the relevant laws, standards and regulations, these Operating Instructions and other documents.

The machine is intended for work in automatic cycles.

The machine operator monitors the process and the operating mode of the machine, replacing material and checking the dimensions. The Operator's position by the machine is not defined.

  1. WARNINGS

Only sheets of the size listed in the parameters can be creased and perforated in the creasing and perforating machine.

  1. Do not crease and perforate foils, sheet metal or other similar materials.
  2. The machine can be only used in enclosed spaces (e.g. offices, shops).
  3. Do not use the machine when the electric cord is damaged.
  4. It is not suggested to use the machine if it makes strange sounds.
  5. Do not connect the machine to voltage different from that indicated on the manufacturer’s identification plate.

Read all instructions before using the machine.

  1. Keep the children away from the machine.
  2. Do not to put fingers or hands into the machine when the electric cord is plugged in.

When the machine is jammed, unplug it then conduct troubleshooting.

Do not replace faulty electrical components with components of different type or different capacity. When replacing a component, the electric cord must be unplugged.

The operator must pay special attention during manipulation with rotary parts of the machine – see yellow Warning Sign (Pos. 40, page 9).

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 5 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 6
Text on page 6
  1. TECHNICAL PARAMETERS

80 – 400 g/m² (creasing, punching) 80 – 250 g/m² (perforating)

CITO 0.04” – paper thickness < 0.01” (recommended grammage 80 – 200 g/m²) “Iron Channel” 0.07” – paper thickness 0.01”

  • 0.02” (recommended grammage 200 – 400 g/m²)

Min./max. number of creases per sheet

Max. number of perforating wheels

13 (for more info refer to Appendix 3)

Min./max. distance between creases

Min. distance of crease from front edge

3,000 sheets LTR/h (with single crease) 4,300 sheets LTR/h (0 crease, only rotary perf./cutting)

52” x 30” x 18.7” 52” x 30” x 48.3” (including table)

net 309 lbs., gross 416 lbs. (including mobile table)

120 V / 60 Hz

  • Note: Respect the recommended width of creasing channel for different paper thickness. If use inappropriate width of crease is used (usually narrow creasing channel for thick paper), inaccuracies in the position of crease may appear, resulting in the crease being placed at a distance different from what was set on the touch screen. If thick paper is used in combination with a narrow crease, it will result in the paper being pressed into the creasing channel, and the rollers starting to slip in an attempt to release the paper. Use wider crease channel in such case.

Page 6 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 7
Text on page 7
  1. MACHINE DESCRIPTION

5.1. Introduction

The electric automatic creasing and perforating machine serves for the processing of graphic material of up

to 17.7” in width. The creasing allows for easy folding of the paper, thereby making the machine convenient

for use in combination with a folding module. Waste-free perforation allows you to tear off the paper easily.

Fig. 1: View of the Machine

1 – Waste drawer

14 – Levelling strip

2 – STOP button

15 – Touch screen

3 – Separator position regulation screw

16 – Front stop (Fig. 8)

4 – Electric switch

17 – Exchangeable tool

5 – Back stop

18 – Front cover

6 – Rear side guide

19 – Plug socket (Fig. 2)

7 – Delivery table

20 – Tool thrust regulation screw (Fig. 2)

8 – Table position regulation screw

21 – Needle bearing

9 – Side guide lock

22 – Safety ring

10 – Side guides turning screw

23 – Top bar (Fig. 1)

11 – Front table

24 – Top bar bearing

12 – Side guide

25 – Guiding, perforating pulley

13 – Front auxiliary table

26 – Thrust pulley

Page 7 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 8
Text on page 8

27 – Rear upper cover

30 – Perforating (Cutting) kit

29 – Fixing sleeve

40 – Warning Sign

Fig. 2: Rear View of the Machine

5.2 Exchangeable tools

In standard equipment, the machine is supplied with the three exchangeable tools described below. Special

tools, such as calendar semi-circle, are available as additional optional accessories (see Appendix 3).

The default setting has been done for all types of tools. A change of the machine function requires the tool

to be replaced (placed by the manufacturer into the waste drawer – 1). Use the electric switch (4) to switch

off the machine, slide out the tool (17) and put in the tool you wish to use.

Loosen the tool screws (31, 32, 33, 34) in order to replace the knives in the tools. Replace the knife and fit

the tool back. Tighten the tool screws (33, 34). Do not overtighten the tool screws (31, 32). Then place the

tool into the machine and perform a trial stroke (see Section 7.5) to ensure the knife and the tool base are

parallel (35). Re-tighten the screws (31, 32). Now the tool is ready for use.

Page 8 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 9
Text on page 9

Fig. 3: Perforating tool 2:1- 9 TPI (571 40 465a) – standard equipment. Micro-perforating tool (571 40 464) as optional accessory.

Fig. 4: Creasing tool CITO 0.04” (571 40 467) – standard equipment. Creasing tool CITO 0.05” (571 40 468) as optional accessory.

Fig. 5: Creasing tool – iron channel 0.07” for heavy grammage (570 40 466)

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 9 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 10
Text on page 10
  1. MACHINE INSTALLATION

Unpack the machine, take it out of the box and remove the four transport bolts at the base of the machine.

Put the machine on the table (refer to Appendix 2 for the table assembly instructions) and use the screws

  1. to attach it to the table. Once the machine is secured, mount the front auxiliary table (13) and the

delivery table (7). When plugged in, the machine is ready to operate. When the electric switch (4) is

switched on, the touch screen (15) will light up. Setting the machine by means of the touch screen is

described in detail in Section 8.

Fig. 6: Machine installation on the table

  1. SETTING THE MACHINE

7.1 Setting the Table

Use the side guides turning screw (10) to set the side guides (12) perpendicularly with the tool. The side

guides are set in the initial position (perpendicular to the tool) if the rear edge of the right side guide aligns

with the feeding table line (fig. 7).

Note: It is recommended to set the side guide perpendicularly in the position as shown in Fig. 7. Besides

the line parallel to the tools, the A2 position line may also be of assistance when identifying the correct side

guide position (the A2 position line must be parallel to the side guide).

Page 10 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 11
Text on page 11

Fig. 7: Setting the Side Guides

Loosen the side guide lock (9). Set the side guides (12) approximately for the paper format size so that the

position of the sheet is symmetrical with the centre of the table. The rulers on the feeding table serve for

exact setting of the side guides (12). Place the levelling strips (14) on the feeding table between the front

side guides (12) – two or four strips according to the paper format.

Front stops (16) must be placed on the feeding table behind the paper for the feeding to run properly (Fig.

Fig. 8: Levelling Strips and Front Stops

Page 11 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 12
Text on page 12

7.1.1 Setting the Table Upper Position

Use the table position regulation screw (8) to set the table upper position. With default settings, the gauge

  1. is approximately in the centre of the hole (Fig. 9). The table upper position may need to be changed

when paper wave needs to be eliminated. Also, change the setting when you change paper thickness. For

thicker paper the table upper position will be closer to the feeding head. Consequently, use the regulation

screw to move the gauge in the direction of the UP position.

Fig. 9: Setting the Table Upper Position

7.2 Setting the Separator

Set the separator position regulation screw (3) in the maximum position (open gap). Put a sample of the

paper you wish to process in the gap between the separator (39) and the feeding head strips (38). Use your

hand to move the sample to and fro and, at the same time, use your other hand to tighten the separator

position regulation screw until the paper can no longer move freely and light resistance is felt. Now carefully

turn the screw back so that the paper can again move freely. This sets the optimum gap between the

separator and the feeding head strip. You may want to move the feeding table to the lower position to get

better access to the separator.

Fig. 10a: Separator Position Regulation Screw

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 12 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 13
Text on page 13

Fig. 10b: Setting the Separator

7.3 Setting Rotary Perforating (Cutting) and Guiding Pulleys

Lift the rear upper cover (27) and use an Allen key to loosen the perforation pulley screws (25) in order to

adjust the perforating or cutting wheels (30). Set the pulleys on the lower shaft in the required position and

tighten up the screws. Then place the perforating wheel (30) in the required position and tighten up with the

Alternatively, you may remove the whole shaft (28) and add or remove pulleys as required. In order to

remove the shaft, use an Allen key to loosen the screw on the fixing sleeve (29 – Fig. 2) and push the

sleeve aside. Then move the whole shaft to the left (in the direction of the side of the machine) and remove

the shaft from the machine. Before you do so, make sure the perforating (cutting) wheels are placed in the

Fig. 11: Setting Rotary Perforating and Cutting

For the machine to operate properly, the thrust pulleys (26) must always be put on the shafts correctly.

Once the setting is finished, tilt the cover (27) down because it operates as a stripper!

Page 13 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 14
Text on page 14

7.3.1 Setting Perforation or Cutting Thrust

Use an Allen key to turn the regulation screw of the perforating kit (30) to set perforation thrust.

Turn in the direction of + for higher thrust. Turn in the direction of - for lower thrust. It is recommended to set

the lowest possible thrust as this will prolong the service life of the perforating pulley.

7.4 Setting Delivery Table

The delivery table (7) is telescopic and can be set in three heights, or removed from the machine.

Fig. 12: Setting Delivery Table

7.5 Adjustment of Top Bar Stroke

Unless the depth of a crease on both sides of the sheet is identical or unless the sheet is torn away evenly

after perforation, the top bar (23) can be moved down using the tool thrust regulation screws (20). It is

necessary to turn the screws gradually by 1/12 of the revolution (30°) to the left (the bar moves downwards)

and then secure them with a nut. Try the quality of perforation after each turn of the screw by 30° and, if

satisfactory, do not turn the screws any more. When adjustment of perforation is finished, the machine is

also to be adjusted for creasing. If the perforating/creasing force exceeds the limit (engine output is

exceeded) and the top bar (23) remains in the lower position, use the electric switch (2) to switch the

machine off and then wait for 20 seconds before you re-start the machine. Press

(tool backwards) under the field UPPER TOOL. The tool is now unlocked and the

thrust can be adjusted using the tool thrust regulation screws (20). Activate

(tool forwards) to make a

  1. SETTING THE MACHINE USING TOUCH SCREEN

Page 14 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 15
Text on page 15

8.1 Touch Screen Preview

When the electric switch (4) is turned on, the Start-up Screen displays on the touch screen showing the machine’s name and picture. After a few seconds this screen automatically changes to the “SETTING” screen.

Fig. 14: “SETTING” Screen

8.2 Overview of Touch Screen Function Icons

to turn on/off the sound signal for key pressing. If the sound is on, there will be a beep when the

active areas on the touch screen are pressed. If the sound is off,

to display the manual control screen, see Section 8.10.

to display the information screen. The data are approximate. Press OK to go back to the

to display the language selection screen and choose the language.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 15 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 16
Text on page 16

Fig. 16: “LANGUAGES” Screen

to display the “SERVICE MENU” screen. This menu is password-protected and accessible only to

the manufacturer’s (distributor’s) service engineers. If you do not know the password, press

the “SETTING” screen (Fig. 17a). Entering the correct password and confirming by OK displays the

“SERVICE MENU” screen. Press OK to go back to the “SETTING” screen.

Fig. 17a: “SERVICE MENU” Screen – Password

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 16 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 17
Text on page 17

Fig. 17b: “SERVICE MENU” Screen

Note: Description of service screen is not part of this document because this screen is not accessible to end user.

8.3 Setting the Feed

Press FEEDING on the “SETTING” screen (Fig. 14) to display the following menu.

Fig. 18: “FEEDING” Screen

Press the number icon next to GRAMMAGE to display a numerical keypad in order to enter the paper

grammage; press ENTER to confirm. Then select FORMAT. This sets and displays the corresponding

values in the SHEET LIFTING and SHEET FANNING fields. If you process an atypical format, select the

format closest in dimensions to the atypical format and adjust the values in the SHEET LIFTING and

Page 17 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 18
Text on page 18

SHEET FANNING fields manually. Now the machine is ready for test paper feed. Press LOAD PAPER

(functions: press – table moves to the lower position; hold – table moves as long as you hold). Then start

the test by pressing

. Use the numeric field over

to enter the number of test sheets if required; the

default value is 1. During the test the screen shows the sheets yet to be processed in the test. Multiple-

sheet test is recommended.

If paper feed is set incorrectly, the machine switches off automatically during the test and the touch screen

displays a red warning INCORRECT FEEDING. Then you need to set the separator (see Section 7.2) or

use the + and - function keys to adjust SHEET LIFTING and SHEET FANNING manually.

8.4 Setting the Number and Position of Creases/Perforations

Press CREASE POSITION on the “SETTING” screen (Fig. 14) to display the following menu.

Fig. 19: “CREASE POSITION” Screen

8.4.1 Most Common Folds

The most commonly used folds are created by placing the crease at exactly defined relative distances of

1/2, 1/3 or 1/4 of the paper. The most common creases are easily set by pressing the corresponding button.

First, place the required sheet of paper to be creased on the feeding table. Then press 1/2 (proceed

Page 18 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 19
Text on page 19

similarly for other types of fold). A single sheet is run through the machine without creasing; the machine

measures the sheet and saves the sheet length in the memory. Values are displayed in their respective

fields when the sheet has passed through. Then start the test by pressing

. Use the field over

the number of test sheets if required; the default value is 1. During the test the screen shows the sheets yet

to be processed in the test. Once the test is completed, it is recommended to check the measured length

before processing the rest of the batch. If the crease is not precisely at the required distance, correct the

distance manually. Then press OK to return to the “SETTING” screen (Fig. 14) and press START

8.4.2 Setting the Number of Segments

Press the numeric icon next to the NO. OF CREASES field on the touch screen to display the numeric

keypad (Fig. 20). By pressing the relevant digit, the number of crease/perforation/punch lines (segments) is

set. You can set as many as 0 – 15 segments. Setting 0 makes the paper just pass through the machine.

This may be suitable if you wish to use only rotary tools (perforating or cutting), see Section 8.4.4. Selection

of the number of segments is ended by pressing the ENTER key. The number of segments is now set.

Fig. 20: Numeric Keypad Screen

8.4.3 Setting the Position of Segments

The position of the first segment is set as the distance from the edge of the sheet. The position of each

following segment is defined as its distance from the previous segment. Use the + and - keys to choose the

required segment. Select 1 in the numeric field next to CREASE NO. and this activates the DISTANCE

numeric icon. A numeric keypad is now displayed. Use the numeric keypad to set the distance from the

edge of the sheet and press ENTER. The position of the first segment is set. Using the + key choose

Page 19 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 20
Text on page 20

segment number 2 and then press the numeric icon under DISTANCE again. Use the numeric keypad to

set the distance from the first segment and press ENTER. The second segment is set. Set all the remaining

segments in the same way. Press

to run a test after you have set all segments.

8.4.4 Rotary Perforating, Cutting

Press ROTARY PERF SETUP to feed paper up to the perforating wheels; the key changes to PAPER

OUT. The screen is inactive while the paper is being fed up to the perforating wheels. The key becomes

active for pressing when the paper has stopped. However, first you need to set the pulleys on the shaft and

perforating/cutting knives (30) into the required position as shown by the graphics on the paper you

process, see Section 7.3. Then press PAPER OUT, the paper is moved out onto the delivery table and the

key changes back to ROTARY PERF SETUP.

If you wish to run only the rotary perforating (cutting), enter 0 next to NO. OF CREASES. For setting the

rotary tools please refer to Section 7.3.

8.5 Setting the Speed of Processing

Press SPEED OF PROCESSING on the “SETTING” screen (Fig. 14) to display the following menu.

Fig. 21: “SPEED OF PROCESSING” Screen

Change speed by using the + and - keys. Minimum and maximum values: 50 and 100, respectively. The

default value is 100, which means 100% speed of the machine (3,000 A4 sheets per hour). The maximum

speed can be reduced by half. Low speeds are suitable for processing papers complicated to feed or using

multiple rotary tools on the shaft. When you have finished the setting, press OK to confirm.

Page 20 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 21
Text on page 21

8.6 Loading Paper

To load paper press LOAD PAPER (functions: press – table moves to the lower position; hold – table

moves as long as you hold).

8.7 Setting Batch

Press the numeric icon next to the field BATCH on the “SETTING” screen (Fig. 14) to display numeric

keypad (Fig. 22). Use the numeric keypad to set the batch (= the number of sheets to be processed by the

machine in a single cycle) and press ENTER to confirm. Enter 0 if you wish to switch the batch off. Batch

processing may be interrupted in three ways:

  1. The machine is stopped by pressing the STOP button

on the touch screen. The touch screen

shows both the total batch and the number of sheets already processed. When you restart the

machine by pressing the START button

, the machine goes on to process the remaining sheets in

  1. Press STOP (2) to stop the machine. The touch screen shows only the total batch and the value

showing the number sheets already processed in the batch is reset to zero. If you press the START

to restart the machine, the machine processes the batch from the beginning.

  1. The machine is switched off using the electric switch (4), or by disconnecting the power supply.

When the machine is switched on again, the batch is not displayed and must be entered anew.

Fig. 22: “BATCH SETTING” Screen

It is also possible to change the batch straight in the Working Screen (Section 8.9, Fig. 25).

8.8 Program Saving and Loading

The software allows saving 5 different programs. Both the values set on the “CREASE POSITION” screen

and those set on the “FEEDING” screen are saved under a program number. Once the feeding and crease

position values are set following the instructions in Sections 8.3 and 8.4, you can go on to save the

Page 21 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 22
Text on page 22

program. Press the numeric icon next to the field PROGRAM on the “SETTING” screen (Fig. 14). The

program saving and loading menu (Fig. 23) is displayed. Use the + and - keys to list values between 0 and

  1. You can save your jobs under 1–5; value 0 indicates no program is saved in the memory.

Fig. 23: “PROGRAM SAVING AND LOADING” Screen

Press SAVE if you have your job ready and wish to save it. In the JOB NAME field you may enter up to 24

characters to name the program you wish to save. The field changes along with the program number. Press

OK to go back to the “SETTING” screen. The program is saved and displayed on the “SETTING” screen.

Load the program in a similar manner. Use + and - to choose a saved program you wish to load. Press

LOAD. Press OK to go back to the “SETTING” screen. The number of the loaded program is displayed next

to the PROGRAM field. The machine is ready to operate according to this program.

Warning: The touch screen displays the number of the last program saved or loaded. For the sake of

effectiveness, the operator can change this program by a different program without saving it. In such case,

the number of the last program saved or loaded is still displayed, but the machine operates according to the

operator’s last setting, even though this setting has not been saved. If the machine is turned off and then

turned on again by the electric switch, the machine operates according to the program displayed on the

touch screen. The last unsaved setting is deleted.

8.9 Starting Working Cycle

Adjust the feeding table (11) according to the instructions in Section 7.1. There must be a minimum gap

between the side guides and the pile of paper. The machine’s design allows loading a pile of paper of up to

2.75” in height. Adjust the distance of the back stop (5) on the delivery table (7) according to the size of the

on the touch screen (Fig. 14). The machine starts running and the touch screen

switches to the “WORKING CYCLE” screen (Fig. 24). The STOP icon

and information about the

program, the batch and the number of processed sheets are displayed on the touch screen.

Page 22 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 23
Text on page 23

Fig. 24: “WORKING CYCLE” Screen

The feeding head starts feeding sheets of paper into the machine. Do not load another pile of paper onto

the feeding table until the machine has processed the last paper, which automatically ends the working

cycle and the “WORKING CYCLE” screen is displayed (Fig. 25). The working cycle can be interrupted

manually by pressing STOP

. In case of emergency the machine can be switched off with the big red

STOP button (2) on the left side of the touch screen.

Fig. 25: Working Screen

If the processing runs as you wish and you want to continue the job, press LOAD PAPER and replenish

paper on the front table. If you need to correct the job, press BACK TO SETTING.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 23 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 24
Text on page 24

8.10 Manual Control

Manual control is mostly used when replacing the tools or when loosening jammed paper from the machine.

(manual control) on the “SETTING” screen (Fig. 14) and the following menu is displayed (Fig. 26).

Press the move forward/backward icons

the arrow is held.

next to the MOVE ROLLERS field to set the machine’s

define the continuity of the run of the rollers.

  • rollers are turning only if
  • rollers start running and rotate until the icon is pressed again. The FEED BELTS

(feeding strips running) and FEEDING TABLE fields work similarly. Press SHEET LIFTING and SHEET

FANNING to run the respective functions. Use

(tool backwards) under the UPPER TOOL field if the

perforation/creasing force gets too high and the top bar (23) remains in the lower position. Press

unlock the tool and adjust the thrust by using the tool thrust regulation screws (20). Activate

forwards) to make a trial stroke. Refer to Section 7.5 for how to use the icons of the UPPER TOOL field.

Press OK to go back to the “SETTING” screen.

Fig. 26: “MANUAL CONTROL” Screen

  1. RECOMMENDED MACHINE MAINTENANCE

Clean dust from the machine after each job using, for example, compressed air. Grease the bearings (positions 21 and 24) with bearing grease annually.

Page 24 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 25
Text on page 25
  1. MACHINE DISPOSAL

After the end of the service life, it is forbidden to dispose of the machine in the municipal waste. The

machine must be disassembled, and metallic, non-metallic, plastic, rubber and electronic parts sorted.

These parts are disposed of at the relevant points of recycling. Some parts of the machine can contain

hazardous substances that are harmful to the environment and health.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 25 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 26
Text on page 26

APPENDIX 1: ACCESSORIES

Creasing Tool (CITO channel 0.04”)

Creasing Tool – “Iron Channel” 0.07”

A perforating tool (571 40 465a) is fitted in the machine for transit. Creasing Tool CITO 0.04” (571 40 467) and Creasing Tool – “Iron Channel” 0.07” (571 40 466) are kept in the waste drawer (1).

Note: The tools for GoCrease F-SPEED and GoCrease AutoAir are identical. As GoCrease AutoAir is wider, a small metal-sheet extension needs to be fitted on this tool; the extension is kept in the waste drawer, see the picture.

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 26 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 27
Text on page 27

Rear side guide (6)

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 27 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 28
Text on page 28

Allen key no. 2

Allen key no. 4

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 28 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 29
Text on page 29

APPENDIX 2: TABLE ASSEMBLING INSTRUCTIONS

POSITION

PCS

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

DESCRIPTION

BASE WHEEL WITH BRAKE BOTTOM BASE SCREW M10x25 NUT M10 WASHER 10.5 SPRING WASHER 10 STAND-FRAME ASSEMBLY SHELF ASSEMBLY SCREW M6x14

Page 29 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 30
Text on page 30

APPENDIX 3: OPTIONAL ACCESSORY

3.1 Punching Tools

  1. Punching tool for wire binding – square 4 x 4 mm, 3:1 (571 40 462)
  2. Punching tool for wire binding – square 5 x 5 mm, 2:1 (571 40 529)
  3. Punching tool for wire binding – round, diameter 4 mm, 3:1 (571 40 475)
  4. Punching tool with calendar semi-circle – square 4 x 4, 3:1 (571 40 463)
  5. Punching tool with calendar semi-circle – round, diameter 4 mm, 3:1 (571 40 476)
  6. Euro Punch tool (571 40 506)

MyBinding.com 5500 NE Moore Court Hillsboro, OR 97124 Toll Free: 1-800-944-4573 Local: 503-640-5920

Page 30 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 31
Text on page 31

3.1.1 Removing Punching Tool Pins

Except for the Euro Punch, all the punching tools specified above have removable pins. To remove the

pins, loosen the 10 screws on the upper edge of the tool and remove the bar under the screws. After you

have removed the bar, use pliers to take each pin out. Then put the bar back in the original position and

Note: For technological reasons, each machine tool features two pin types of different lengths (the approximate length difference is 0.02”). When you have removed the pins, make sure you mark which pin is fitted in which hole so that you can fit the pins back in the correct holes. If you fit a pin in the wrong hole, the passage of the pin through the paper may become impaired.

3.2 Rotary Tools

You can fit as many as 13 rotary tools on the shaft (28) at the machine output.

572 59 270 Complete perforating kit

572 59 271 Complete cutting kit

Note: 1x complete perforating kit (572 59 570) and 1x cutting wheel (572 75 916) comes as part of the standard equipment.

Page 31 of 32

MBM GoCrease AutoAir Creasing/Perforating/Punching Machine User Manual, page 32
Text on page 32

10 perforating kits fitted (max 13)

APPENDIX 4: THE MOST COMMON FAULTS (TROUBLESHOOTING)

  1. The START key

There is no paper on the feeding table or the paper is not pushed close to the stainless steel plate and the feeding table sensor cannot sense paper.

  1. Paper jammed inside the machine

Paper can be released using the “Forward” and “Backward” manual control functions – Section 8.10. If this does not help, take out the exchangeable tool (17) and try to release the paper again using the "Forward" and "Backward" functions.

  1. Uneven perforation (creasing)

See Section 7.5 Adjustment of top bar stroke.

  1. Keys on the touch screen unit not working

Reset the machine (turn it off and then on again).

  1. If START key does not respond and nothing happens while black or dark paper is being processed, it is very likely that the feeding table sensor struggles to detect the paper. Placing one sheet of white or light paper on the top of the pile will resolve the issue.
  2. Machine does not feed paper or feeds multiple sheets
  • Check the separator setting (Section 7.2).
  • Check the SHEET LIFTING and SHEET FANNING settings.
  • This fault may be caused by a static charge, which keeps the sheets stuck together. Fan out the sheet pile properly (ideally using an air hose).

If the problem persists, please ask you dealer for assistance.

Page 32 of 32 ยท End of manual

Quick start

  1. Punching tool for wire binding – square 4 x 4 mm, 3:1 (571 40 462)
  2. Punching tool for wire binding – square 5 x 5 mm, 2:1 (571 40 529)
  3. Punching tool for wire binding – round, diameter 4 mm, 3:1 (571 40 475)
  4. Punching tool with calendar semi-circle – square 4 x 4, 3:1 (571 40 463)
  5. Punching tool with calendar semi-circle – round, diameter 4 mm, 3:1 (571 40 476)
  6. Euro Punch tool (571 40 506)

Troubleshooting

ProblemLikely causeFix (from the manual)
START key does not workThere is no paper on the feeding table, or the paper is not pushed close to the stainless steel plate, so the sensor cannot sense it.Load paper and push it close to the stainless steel plate. Page 32
START key does not respond with black or dark paperThe feeding table sensor has trouble detecting dark paper.Place one sheet of white or light paper on top of the pile. Page 32
Paper is jammed inside the machinePaper stuck in the machine.Release it with the Forward and Backward manual controls. If that fails, take out the exchangeable tool and try again. Unplug the machine before troubleshooting a jam. Page 32
Uneven perforation or creasingThe top bar stroke needs adjusting.See Section 7.5, Adjustment of top bar stroke. Page 32
Touch screen keys do not workThe screen needs a reset.Turn the machine off and then on again. Page 32
Machine does not feed paper or feeds multiple sheetsThe separator or sheet lifting and fanning settings may be off, or static is keeping sheets stuck together.Check the separator setting (Section 7.2) and the SHEET LIFTING and SHEET FANNING settings. Fan out the pile well, ideally with an air hose. If it continues, ask your dealer. Page 32

Frequently asked questions

How many programs can I save on the GoCrease AutoAir?

You can save jobs under programs 1 to 5. Value 0 means nothing is saved. You can name a program with up to 24 characters. See page 22.

How tall a pile of paper can I load?

The machine can take a pile up to 2.75 inches high. Keep a minimum gap between the side guides and the pile. See page 22.

What should I do if paper jams?

Unplug the machine first. Then use the Forward and Backward manual controls to release the paper. If that does not work, take out the exchangeable tool and try again. See page 32.

Why does the machine feed several sheets at once?

Static charge can keep sheets stuck together. Fan out the pile properly, ideally with an air hose, and check the separator and sheet lifting and fanning settings. See page 32.

Can I crease foil or sheet metal?

No. Do not crease or perforate foils, sheet metal or similar materials. Only sheet sizes listed in the machine parameters can be creased and perforated. See page 5.